| 1. |
|
|
| 2. |
|
|
| 3. |
|
|
| 4. |
|
|
| 5. |
- Fenstermacher, M.E., et al.
(författare)
-
DIII-D research advancing the physics basis for optimizing the tokamak approach to fusion energy
- 2022
-
Ingår i: Nuclear Fusion. - : IOP Publishing. - 0029-5515 .- 1741-4326. ; 62:4
-
Tidskriftsartikel (refereegranskat)abstract
- DIII-D physics research addresses critical challenges for the operation of ITER and the next generation of fusion energy devices. This is done through a focus on innovations to provide solutions for high performance long pulse operation, coupled with fundamental plasma physics understanding and model validation, to drive scenario development by integrating high performance core and boundary plasmas. Substantial increases in off-axis current drive efficiency from an innovative top launch system for EC power, and in pressure broadening for Alfven eigenmode control from a co-/counter-I p steerable off-axis neutral beam, all improve the prospects for optimization of future long pulse/steady state high performance tokamak operation. Fundamental studies into the modes that drive the evolution of the pedestal pressure profile and electron vs ion heat flux validate predictive models of pedestal recovery after ELMs. Understanding the physics mechanisms of ELM control and density pumpout by 3D magnetic perturbation fields leads to confident predictions for ITER and future devices. Validated modeling of high-Z shattered pellet injection for disruption mitigation, runaway electron dissipation, and techniques for disruption prediction and avoidance including machine learning, give confidence in handling disruptivity for future devices. For the non-nuclear phase of ITER, two actuators are identified to lower the L-H threshold power in hydrogen plasmas. With this physics understanding and suite of capabilities, a high poloidal beta optimized-core scenario with an internal transport barrier that projects nearly to Q = 10 in ITER at ∼8 MA was coupled to a detached divertor, and a near super H-mode optimized-pedestal scenario with co-I p beam injection was coupled to a radiative divertor. The hybrid core scenario was achieved directly, without the need for anomalous current diffusion, using off-axis current drive actuators. Also, a controller to assess proximity to stability limits and regulate β N in the ITER baseline scenario, based on plasma response to probing 3D fields, was demonstrated. Finally, innovative tokamak operation using a negative triangularity shape showed many attractive features for future pilot plant operation.
|
|
| 6. |
- Poley, L., et al.
(författare)
-
The ABC130 barrel module prototyping programme for the ATLAS strip tracker
- 2020
-
Ingår i: Journal of Instrumentation. - : IOP PUBLISHING LTD. - 1748-0221 .- 1748-0221. ; 15:9
-
Tidskriftsartikel (refereegranskat)abstract
- For the Phase-II Upgrade of the ATLAS Detector [1], its Inner Detector, consisting of silicon pixel, silicon strip and transition radiation sub-detectors, will be replaced with an all new 100% silicon tracker, composed of a pixel tracker at inner radii and a strip tracker at outer radii. The future ATLAS strip tracker will include 11,000 silicon sensor modules in the central region (barrel) and 7,000 modules in the forward region (end-caps), which are foreseen to be constructed over a period of 3.5 years. The construction of each module consists of a series of assembly and quality control steps, which were engineered to be identical for all production sites. In order to develop the tooling and procedures for assembly and testing of these modules, two series of major prototyping programs were conducted: an early program using readout chips designed using a 250 nm fabrication process (ABCN-250) [2, 3] and a subsequent program using a follow-up chip set made using 130 nm processing (ABC130 and HCC130 chips). This second generation of readout chips was used for an extensive prototyping program that produced around 100 barrel-type modules and contributed significantly to the development of the final module layout. This paper gives an overview of the components used in ABC130 barrel modules, their assembly procedure and findings resulting from their tests.
|
|
| 7. |
|
|
| 8. |
- Guha, N, et al.
(författare)
-
Lung cancer risk in painters: results from the SYNERGY pooled case-control study consortium
- 2021
-
Ingår i: Occupational and environmental medicine. - : BMJ. - 1470-7926 .- 1351-0711. ; 78:4, s. 269-278
-
Tidskriftsartikel (refereegranskat)abstract
- We evaluated the risk of lung cancer associated with ever working as a painter, duration of employment and type of painter by histological subtype as well as joint effects with smoking, within the SYNERGY project.MethodsData were pooled from 16 participating case–control studies conducted internationally. Detailed individual occupational and smoking histories were available for 19 369 lung cancer cases (684 ever employed as painters) and 23 674 age-matched and sex-matched controls (532 painters). Multivariable unconditional logistic regression models were adjusted for age, sex, centre, cigarette pack-years, time-since-smoking cessation and lifetime work in other jobs that entailed exposure to lung carcinogens.ResultsEver having worked as a painter was associated with an increased risk of lung cancer in men (OR 1.30; 95% CI 1.13 to 1.50). The association was strongest for construction and repair painters and the risk was elevated for all histological subtypes, although more evident for small cell and squamous cell lung cancer than for adenocarcinoma and large cell carcinoma. There was evidence of interaction on the additive scale between smoking and employment as a painter (relative excess risk due to interaction >0).ConclusionsOur results by type/industry of painter may aid future identification of causative agents or exposure scenarios to develop evidence-based practices for reducing harmful exposures in painters.
|
|
| 9. |
|
|
| 10. |
|
|
