| 1. |
- Alkadir Abdulahi, Birhan, 1985, et al.
(författare)
-
Open-Circuit Voltage Modulations on All-Polymer Solar Cells by Side Chain Engineering on 4,8-Di(thiophen-2-yl)benzo[1,2- b:4,5- b′]dithiophene-Based Donor Polymers
- 2018
-
Ingår i: ACS Applied Energy Materials. - : American Chemical Society (ACS). - 2574-0962. ; 1:6, s. 2918-2926
-
Tidskriftsartikel (refereegranskat)abstract
- In recent years, all-polymer solar cells (all-PSCs), incorporating active layers based on blends of electron-donor (D) and acceptor (A) polymers, have drawn attention because of the advantages they hold in the flexibility of choosing the D:A combinations to modulate their energy levels and to improve their overall open-circuit voltages (V oc ) and power conversion efficiencies (PCE)s. V oc is one of the key parameters for the determination of the PCEs of PSCs. In this work, we synthesized six donor polymers with three different side chains appended to the 4,8-di(thiophen-2-yl)benzo[1,2-b:4,5-b′]dithiophene (BDT) units. By substituting carbon with sulfur and silicon atoms at the 5-position of the thiophenes attached to the BDT units, the highest occupied molecular orbital (HOMO) levels of the donor polymers could be successfully lowered. As anticipated, the V oc values of the resulting all-PSCs increased along with the lowering of the HOMO levels of the donor polymers. Among the six all-PSCs, the PBDT-BDD:PNDI-T10 all-PSC realized a balance between the photovoltage and photocurrent, where a decent PCE of 5.6% was obtained with a V oc of 0.9 V and a photocurrent of 10.5 mA/cm 2 .
|
|
| 2. |
|
|
| 3. |
- Alkadir Abdulahi, Birhan, 1985, et al.
(författare)
-
Structural engineering of pyrrolo[3,4-: F] benzotriazole-5,7(2 H,6 H)-dione-based polymers for non-fullerene organic solar cells with an efficiency over 12%
- 2019
-
Ingår i: Journal of Materials Chemistry A. - : Royal Society of Chemistry (RSC). - 2050-7488 .- 2050-7496. ; 7:33, s. 19522-19530
-
Tidskriftsartikel (refereegranskat)abstract
- In this work, we have synthesized two wide band gap donor polymers based on benzo[1,2-b:4,5-b′]dithiophene (BDT) and pyrrolo[3,4-f]benzotriazole-5,7(2H,6H)-dione (TzBI), namely, PBDT-TzBI and PBDT-F-TzBI and studied their photovoltaic properties by blending them with ITIC as an acceptor. Polymer solar cell devices made from PBDT-TzBI:ITIC and PBDT-F-TzBI:ITIC exhibited power conversion efficiencies (PCEs) of 9.22% and 11.02% and while annealing at 160 °C, improved the device performances to 10.24% and 11.98%, respectively. Upon solvent annealing with diphenyl ether (DPE) (0.5%) and chlorobenzene (CB), the PCE of the PBDT-F-TzBI-based device increased to 12.12%. The introduction of the fluorinated benzodithiophene (BDT-F) moiety on the backbone of PBDT-F-TzBI improved the open circuit voltage, short circuit current and fill factor simultaneously. The high PCEs of the PBDT-F-TzBI:ITIC-based devices were supported by comparison and analysis of the optical and electronic properties, the charge carrier mobilities, exciton dissociation probabilities, and charge recombination behaviors of the devices.
|
|
| 4. |
- Gedefaw, Desta Antenehe, 1971, et al.
(författare)
-
An alternating copolymer of fluorene donor and quinoxaline acceptor versus a terpolymer consisting of fluorene, quinoxaline and benzothiadiazole building units: synthesis and characterization
- 2016
-
Ingår i: Polymer Bulletin. - : Springer Science and Business Media LLC. - 0170-0839 .- 1436-2449. ; 73:4, s. 1167-1183
-
Tidskriftsartikel (refereegranskat)abstract
- An alternating polyfluorene copolymer based on fluorene donor and quinoxaline acceptor (P1) and an alternating terpolymer (P2) with fluorene (50 %) donor and quinoxaline (25 %) and benzothiadiazole (25 %) acceptor units were designed and synthesized for use as photoactive materials in solar cells. The presence of benzothiadiazole unit in P2 increased the optical absorption coverage in the range of 350-600 nm, which is an interesting property and a big potential for achieving improved photovoltaic performances with judicious optimization of the devices. Solar cells were fabricated from 1:4 blends of polymers-PCBM[70] using o-dichlorobenzene (o-DCB) as processing solvent, and P1 showed a power conversion efficiency (PCE) of 3.18 %, with a short-circuit current density (J (SC)) of 7.78 mA/cm(2), an open-circuit voltage (V (OC)) of 0.82 V, and a fill factor (FF) of 50 % while P2 showed an overall PCE of 2.14 % with corresponding J (SC) of 5.97 mA/cm(2), V (OC) of 0.84 V and FF of 42 %. In general, P2 gave lower J (SC) and FF presumably due to the fine domain sizes of the polymer-PCBM[70] blend as seen from the atomic force microscopy (AFM) image which might have affected the charge carrier transport. Alternating (P1) and ternary (P2) conjugated polymers were designed, synthesized and used for fabrication of photovoltaic devices.
|
|
| 5. |
- Genene, Zewdneh, 1983, et al.
(författare)
-
A comparative study of the photovoltaic performances of terpolymers and ternary systems
- 2017
-
Ingår i: RSC Advances. - : Royal Society of Chemistry (RSC). - 2046-2069. ; 7:29, s. 17959-17967
-
Tidskriftsartikel (refereegranskat)abstract
- Random terpolymers were synthesized from the electron-rich unit thiophene as the donor and two electron-deficient units with complementary absorption as the acceptor. Polymer solar cells (PSCs) fabricated from these terpolymers were compared with those fabricated from the ternary blends of two alternating polymers to explore the best strategy for extending the light absorption range. The two approaches showed similar open-circuit voltages (Voc) but different short-circuit current densities (Jsc). The terpolymer strategy broadened the light absorption range and provided a high power conversion efficiency (PCE) of 5.8%. This is due to a high Jsc and high hole mobility. The device fabricated from the ternary blend exhibited a lower PCE (3.5%) compared to those fabricated from the terpolymers and alternating polymer blends due to the morphological incompatibility of the donor polymers. Our results illustrate the potential of the terpolymer systems as a promising strategy to effectively increase the light absorption and thereby performance of PSCs by combining two morphologically incompatible polymers.
|
|
| 6. |
- Genene, Zewdneh, 1983, et al.
(författare)
-
Recent Advances in n-Type Polymers for All-Polymer Solar Cells
- 2019
-
Ingår i: Advanced Materials. - : Wiley. - 0935-9648 .- 1521-4095. ; 31:22
-
Forskningsöversikt (refereegranskat)abstract
- © 2019 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim All-polymer solar cells (all-PSCs) based on n- and p-type polymers have emerged as promising alternatives to fullerene-based solar cells due to their unique advantages such as good chemical and electronic adjustability, and better thermal and photochemical stabilities. Rapid advances have been made in the development of n-type polymers consisting of various electron acceptor units for all-PSCs. So far, more than 200 n-type polymer acceptors have been reported. In the last seven years, the power conversion efficiency (PCE) of all-PSCs rapidly increased and has now surpassed 10%, meaning they are approaching the performance of state-of-the-art solar cells using fullerene derivatives as acceptors. This review discusses the design criteria, synthesis, and structure–property relationships of n-type polymers that have been used in all-PSCs. Additionally, it highlights the recent progress toward photovoltaic performance enhancement of binary, ternary, and tandem all-PSCs. Finally, the challenges and prospects for further development of all-PSCs are briefly considered.
|
|
| 7. |
- Haigh, Paul Anthony, et al.
(författare)
-
Experimental demonstration of staggered cap modulation for low bandwidth red-emitting polymer-LED based visible light communications
- 2019
-
Ingår i: 2019 IEEE International Conference on Communications Workshops, ICC Workshops 2019 - Proceedings.
-
Konferensbidrag (refereegranskat)abstract
- © 2019 IEEE. In this paper we experimentally demonstrate, for the first time, staggered carrier-less amplitude and phase (sCAP) modulation for visible light communication systems based on polymer light-emitting diodes emitting at ∼639 nm. The key advantage offered by sCAP in comparison to conventional multiband CAP is its full use of the available spectrum. In this work, we compare sCAP, which utilises four orthogonal filters to generate the signal, with a conventional 4-band multi-CAP system and on-off keying (OOK). We transmit each modulation format with equal energy and present a record un-coded transmission speed of ∼6 Mb/s. This represents gains of 25% and 65% over the achievable rate using 4-CAP and OOK, respectively.
|
|
| 8. |
- Murto, Petri Henrik, 1984, et al.
(författare)
-
High performance all-polymer photodetector comprising a donor-Acceptor-Acceptor structured indacenodithiophene-bithieno[3,4-c] pyrroletetrone copolymer
- 2018
-
Ingår i: ACS Macro Letters. - : American Chemical Society (ACS). - 2161-1653. ; 7:4, s. 395-400
-
Tidskriftsartikel (refereegranskat)abstract
- The synthesis of an acceptor polymer PIDT-2TPD, comprising indacenodithiophene (IDT) as the electron-rich unit and an interconnected bithieno[3,4-c]pyrrole-4,4′,6,6′-Tetrone (2TPD) as the electron-deficient unit, and its application for all-polymer photodetectors is reported. The optical, electrochemical, charge transport, and device properties of a blend of poly(3-hexylthiophene) and PIDT-2TPD are studied. The blend shows strong complementary absorption and balanced electron and hole mobility, which are desired properties for a photoactive layer. The device exhibits dark current density in the order of 10 -5 mA/cm 2 , external quantum efficiency broadly above 30%, and nearly planar detectivity over the entire visible spectral range (maximum of 1.1 × 10 12 Jones at 610 nm) under-5 V bias. These results indicate that PIDT-2TPD is a highly functional new type of acceptor and further motivate the use of 2TPD as a building block for other n-Type materials.
|
|
| 9. |
- Negash, Asfaw, et al.
(författare)
-
Diketopyrrolopyrrole-based terpolymers with tunable broad band absorption for fullerene and fullerene-free polymer solar cells
- 2019
-
Ingår i: Journal of Materials Chemistry C. - : Royal Society of Chemistry (RSC). - 2050-7534 .- 2050-7526. ; 7:11, s. 3375-3384
-
Tidskriftsartikel (refereegranskat)abstract
- A series of random terpolymers with donor-acceptor-donor-acceptor molecular configuration, comprising fluorinated benzotriazole (FTAZ) and thienothiophene-capped diketopyrrolopyrrole (TTDPP) as the first and second electron-accepting moieties and thienyl-substituted benzodithiophene (BDTT) as the electron-donating unit, are designed for polymer solar cells. By tuning the ratio of TTDPP and FTAZ, the optoelectronic properties of the terpolymers are systematically varied. All materials exhibit a broad absorption window spanning from 300 to 900 nm, illustrating the success of the terpolymer approach. Fullerene-based polymer solar cells fabricated from the terpolymer with the highest content of TTDPP afford a power conversion efficiency of 5.7%, with a short-circuit current density of 15.2 mA cm -2 . On the other hand, solar cell devices composed of the terpolymer with the lowest content of TTDPP and the narrow gap non-fullerene acceptor IEICO-4F exhibit a higher efficiency of 6.3%, with an enhanced short-circuit current density of 17.5 mA cm -2 , as a result of a better complementarity in the absorption of the donor and acceptor materials and well-balanced charge carrier mobilities. This efficiency represents the best value for fullerene-free polymer solar cells based on DPP-containing polymers to date.
|
|
| 10. |
- Negash, Asfaw, et al.
(författare)
-
Ladder-type high gap conjugated polymers based on indacenodithieno[3,2-b]thiophene and bithiazole for organic photovoltaics
- 2019
-
Ingår i: Organic Electronics: physics, materials, applications. - : Elsevier BV. - 1566-1199. ; 74, s. 211-217
-
Tidskriftsartikel (refereegranskat)abstract
- © 2019 Elsevier B.V. Two push-pull type conjugated polymers - PIDTT−BTz and PIDTT−DTBTz, based on the ladder-type donor unit indacenodithieno[3,2-b]thiophene (IDTT) and bithiazole (BTz) as acceptor component - are designed and synthesized for photovoltaic applications. The polymers exhibit relatively high optical gaps of ~2.0 eV with strong absorption in the range of 400–600 nm, rendering them of particular interest for the harvesting of indoor light and/or multijunction devices. Electrochemical investigations indicate a lower highest occupied molecular orbital energy level (−5.44 eV) for PIDTT−BTz as compared to PIDTT−DTBTz (−5.36 eV), enabling to achieve a higher open-circuit voltage. Under solar illumination, the best power conversion efficiency (5.1%) is achieved for the combination PIDTT−DTBTz:PC71BM (compared to 4.6% for PIDTT−BTz:PC71BM).
|
|
