| 1. |
|
|
| 2. |
- Ades, M., et al.
(författare)
-
Global Climate : in State of the climate in 2019
- 2020
-
Ingår i: Bulletin of The American Meteorological Society - (BAMS). - : American Meteorological Society. - 0003-0007 .- 1520-0477. ; 101:8, s. S17-S127
-
Tidskriftsartikel (refereegranskat)
|
|
| 3. |
- Ades, M., et al.
(författare)
-
GLOBAL CLIMATE
- 2020
-
Ingår i: BULLETIN OF THE AMERICAN METEOROLOGICAL SOCIETY. - 0003-0007 .- 1520-0477. ; 101:8
-
Tidskriftsartikel (refereegranskat)
|
|
| 4. |
|
|
| 5. |
- Fellinger, Joris, et al.
(författare)
-
Tungsten based divertor development for Wendelstein 7-X
- 2023
-
Ingår i: Nuclear Materials and Energy. - 2352-1791. ; 37
-
Tidskriftsartikel (refereegranskat)abstract
- Wendelstein 7-X, the world’s largest superconducting stellarator in Greifswald (Germany), started plasma experiments with a water-cooled plasma-facing wall in 2022, allowing for long pulse operation. In parallel, a project was launched in 2021 to develop a W based divertor, replacing the current CFC divertor, to demonstrate plasma performance of a stellarator with a reactor relevant plasma facing materials with low tritium retention. The project consists of two tasks: Based on experience from the previous experimental campaigns and improved physics modelling, the geometry of the plasma-facing surface of the divertor and baffles is optimized to prevent overloads and to improve exhaust. In parallel, the manufacturing technology for a W based target module is qualified. This paper gives a status update of project. It focusses on the conceptual design of a W based target module, the manufacturing technology and its qualification, which is conducted in the framework of the EUROfusion funded WPDIV program. A flat tile design in which a target module is made of a single target element is pursued. The technology must allow for moderate curvatures of the plasma-facing surface to follow the magnetic field lines. The target element is designed for steady state heat loads of 10 MW/m2 (as for the CFC divertor). Target modules of a similar size and weight as for the CFC divertor are assumed (approx. < 0.25 m2 and < 60 kg) using the existing water cooling infrastructure providing 5 l/s and roughly maximum 15 bar pressure drop per module. The main technology under qualification is based on a CuCrZr heat sink made either by additive manufacturing using laser powder bed fusion (LPBF) or by uniaxial diffusion welding of pre-machined forged CuCrZr plates. After heat treatment, the plasma-facing side of the heat sink is covered by W or if feasible by the more ductile WNiFe, preferably by coating or alternatively by hot isostatic pressing W based tiles with a soft OFE-Cu interlayer. Last step is a final machining of the plasma-exposed surface and the interfaces to the water supply lines and supports to correct manufacturing deformations.
|
|
| 6. |
- Dehghani, H., et al.
(författare)
-
The role of microscale solid matrix compressibility on the mechanical behaviour of poroelastic materials
- 2020
-
Ingår i: European Journal of Mechanics, A/Solids. - : Elsevier BV. - 0997-7538. ; 83
-
Tidskriftsartikel (refereegranskat)abstract
- We present the macroscale three-dimensional numerical solution of anisotropic Biot's poroelasticity, with coefficients derived from a micromechanical analysis as prescribed by the asymptotic homogenisation technique. The system of partial differential equations (PDEs) is discretised by finite elements, exploiting a formal analogy with the fully coupled thermal displacement systems of PDEs implemented in the commercial software Abaqus. The robustness of our computational framework is confirmed by comparison with the well-known analytical solution of the one-dimensional Therzaghi's consolidation problem. We then perform three-dimensional numerical simulations of the model in a sphere (representing a biological tissue) by applying a given constant pressure in the cavity. We investigate how the macroscale radial displacements (as well as pressures) profiles are affected by the microscale solid matrix compressibility (MSMC). Our results suggest that the role of the MSMC on the macroscale displacements becomes more and more prominent by increasing the length of the time interval during which the constant pressure is applied. As such, we suggest that parameter estimation based on techniques such as poroelastography (which are commonly used in the context of biological tissues, such as the brain, as well as solid tumours) should allow for a sufficiently long time in order to give a more accurate estimation of the mechanical properties of tissues.
|
|
