| 1. |
|
|
| 2. |
- Zettersten, Camilla, et al.
(författare)
-
The influence of the thin-layer flow cell design on the mass spectra when coupling electrochemistry to electrospray ionisation mass spectrometry
- 2006
-
Ingår i: Journal of Electroanalytical Chemistry. - : Elsevier BV. - 0022-0728 .- 1873-2569 .- 1572-6657. ; 590:1, s. 90-99
-
Tidskriftsartikel (refereegranskat)abstract
- The influence of the flow cell configuration on the mass spectra obtained when coupling an electrochemical thin-layer flow cell to electrospray mass spectrometry (ESI-MS) has been investigated. It is shown that interferences due to the electrochemical reaction on the counter electrode and/or the absence of 100% conversion efficiency can alter the mass spectra when conventional thin-layer flow cells are used in conjunction with ESI-MS. The effects, which affect the intensities and distribution of the peaks in the mass spectra, can result in the inability to detect products formed at the working electrode. Comparisons of mass spectra, generated after the electrochemical oxidation of a dinuclear Mn complex (where bpmp = 2,6-bis[bis(2-pyridylmethyl) amino]methyl-4-methylphenol) using two different thin-layer flow cells clearly show that the potential dependence and appearance of the mass spectra depend on the flow cell configuration used. The use of a modified thin-layer flow cell, in which the counter electrode had been separated from the working electrode, gave rise to significantly increased intensities for the oxidised MnIII,IV state of the complex. With the conventional unmodified cell, the corresponding complex was only seen for considerably higher oxidation potentials. The different results can be explained by the reduced risk of redox cycling and interferences due to species generated at the counter electrode with the modified cell. As interferences due to the counter electrode reactions likewise may be expected with many coulometric flow cells, the electrochemical cell design clearly needs to be considered when using electrochemistry coupled to ESI-MS to study electrochemical reactions.
|
|
| 3. |
|
|
| 4. |
|
|
| 5. |
|
|
| 6. |
- Bryngelsson, Hanna, et al.
(författare)
-
Electrodeposited Sb and Sb/Sb2O3 nanoparticle coatings as anode materials for Li-ion batteries
- 2007
-
Ingår i: Chemistry of Materials. - : American Chemical Society (ACS). - 0897-4756 .- 1520-5002. ; 19:5, s. 1170-1180
-
Tidskriftsartikel (refereegranskat)abstract
- Galvanostatically electrodeposited coatings of pure Sb or co-deposited Sb and Sb2O3 nanoparticles, prepared from antimony tartrate solutions, were studied as anode materials in Li-ion batteries. It is demonstrated that the co-deposition of 20-25% (w/w) Sb2O3 results from a local pH increase at the cathode (due to protonation of liberated tartrate) in poorly buffered solutions. This causes precipitation of Sb2O3 nanoparticles and inclusion of some of the particles in the deposit where they become coated with a protecting layer of Sb. Chronopotentiometric cycling of the deposits, which also were characterized using, e.g., SEM, TEM, and XRD, clearly showed that the Sb2O3-containing deposits were superior as anode materials. While the Sb/Sb2O3 coatings exhibited a specific capacity close to the Sb theoretical value of 660 mA·h·g -1 during more than 50 cycles, the capacity for the Sb coatings gradually decreased to about 250 mA·h·g-1. This indicates that the influence of the significant volume changes present upon the formation and oxidation of Li3Sb was much smaller for the Sb/Sb2O3 nanoparticle coatings. The improved performance can be explained by significant formation of Sb2O3 during the reoxidation, the presence of smaller Sb particles in the Sb/Sb2O3 coatings, and the formation of buffering nanoparticles of Li2O in a matrix of Sb during the first reduction cycle for the Sb/Sb2O3 deposits.
|
|
| 7. |
- Bryngelsson, Hanna, et al.
(författare)
-
Electrodeposition and electrochemical characterisation of thick and thin coatings of Sb and Sb/Sb2O3 particles for Li-ion battery anodes
- 2007
-
Ingår i: Electrochimica Acta. - : Elsevier BV. - 0013-4686 .- 1873-3859. ; 53:3, s. 1062-1073
-
Tidskriftsartikel (refereegranskat)abstract
- The possibilities to electrodeposit thick coatings composed of nanoparticles of Sb and Sb2O3 for use as high-capacity anode materials in Li-ion batteries have been investigated. It is demonstrated that the stability of the coatings depends on their Sb2O3 concentrations as well as microstructure. The electrodeposition reactions in electrolytes with different pH and buffer capacities were studied using chronopotentiometry and electrochemical quartz crystal microbalance measurements. The obtained deposits, which were characterised with XRD and SEM, were also tested as anode materials in Li-ion batteries. The influence of the pH and buffer capacity of the deposition solution on the composition and particle size of the deposits were studied and it is concluded that depositions from a poorly buffered solution of antimony-tartrate give rise to good anode materials due to the inclusion of precipitated Sb2O3 nanoparticles in the Sb coatings. Depositions under conditions yielding pure Sb coatings give rise to deposits composed of large crystalline particles with poor anode stabilities. The presence of a plateau at about 0.8V versus Li+/Li due to SEI forming reactions and the origin of another plateau at about 0.4 V versus Li+/Li seen during the lithiation of thin Sb coatings are also discussed. It is demonstrated that the 0.4 V plateau is present for Sb coatings for which the (0 1 2) peak is the main peak in the XRD diffractogram.
|
|
| 8. |
|
|
| 9. |
- Bryngelsson, Hanna, et al.
(författare)
-
Thin films of Cu2Sb and Cu9Sb2 as anode materials in Li-ion batteries
- 2008
-
Ingår i: Electrochimica Acta. - : Elsevier BV. - 0013-4686 .- 1873-3859. ; 53:24, s. 7226-7234
-
Tidskriftsartikel (refereegranskat)abstract
- Thin Cu2Sb films have been prepared by heat-treating Sb films. electrodeposited on Cu substrates. The influence of the electrodeposition conditions and the heat-treatment period on composition and morphology of the films were investigated (SEM and XRD) and the obtained films were tested as anode materials for Li-ion batteries. The Cu2Sb material showed a stable capacity of 290 mAh g(-1) (close to the theoretical capacity of 323 mAh g-1) during more than 60 cycles. The presence of 9-11% (w/w) Sb2O3 in the electrodeposited films resulted in smaller particles but also slowed down formation of Cu2Sb during the heat-treatment step. The presence of Sb2O3 was found to decrease the cycling stability although structural reversibility of Cu2Sb was obtained both with and without Sb2O3. Longer heat-treatment of pure Sb films resulted in the formation of Cu9Sb2 which was shown to be reduced at a lower potential than Cu2Sb. The Cu9Sb2 was converted to Cu2Sb during repeated cycling and the capacity of the latter Cu2Sb material was found to be 230 mAh g(-1). While reduction of the materials was complicated by simultaneous formation of an SEI layer, three plateaus Could be identified during the oxidation of Li3Sb, indicating the presence of three separate one-electron oxidation reactions.
|
|
| 10. |
- Cheah, Seng Kian, et al.
(författare)
-
Self-Supported Three-Dimensional Nanoelectrodes for Microbattery Applications
- 2009
-
Ingår i: Nano letters (Print). - : American Chemical Society. - 1530-6984 .- 1530-6992. ; 9:9, s. 3230-3233
-
Tidskriftsartikel (refereegranskat)abstract
- A nanostructured three-dimensional (3D) microbattery has been produced and cycled in a Li-ion battery. It consists of a current collector of aluminum nanorods, a uniform layer of 17 nm TiO2 covering the nanorods made using ALD, an electrolyte and metallic lithium counter electrode. The battery is electrochemically cycled more than 50 times. The increase in total capacity is 10 times when using a 3D architechture compared to a 2D system for the same footprint area.
|
|
