| 1. |
- Romanelli, F, et al.
(författare)
-
Overview of the JET results
- 2011
-
Ingår i: Nuclear Fusion. - : IOP Publishing. - 1741-4326 .- 0029-5515. ; 51:9
-
Tidskriftsartikel (refereegranskat)abstract
- Since the last IAEA Conference JET has been in operation for one year with a programmatic focus on the qualification of ITER operating scenarios, the consolidation of ITER design choices and preparation for plasma operation with the ITER-like wall presently being installed in JET. Good progress has been achieved, including stationary ELMy H-mode operation at 4.5 MA. The high confinement hybrid scenario has been extended to high triangularity, lower ρ*and to pulse lengths comparable to the resistive time. The steady-state scenario has also been extended to lower ρ*and ν*and optimized to simultaneously achieve, under stationary conditions, ITER-like values of all other relevant normalized parameters. A dedicated helium campaign has allowed key aspects of plasma control and H-mode operation for the ITER non-activated phase to be evaluated. Effective sawtooth control by fast ions has been demonstrated with3He minority ICRH, a scenario with negligible minority current drive. Edge localized mode (ELM) control studies using external n = 1 and n = 2 perturbation fields have found a resonance effect in ELM frequency for specific q95values. Complete ELM suppression has, however, not been observed, even with an edge Chirikov parameter larger than 1. Pellet ELM pacing has been demonstrated and the minimum pellet size needed to trigger an ELM has been estimated. For both natural and mitigated ELMs a broadening of the divertor ELM-wetted area with increasing ELM size has been found. In disruption studies with massive gas injection up to 50% of the thermal energy could be radiated before, and 20% during, the thermal quench. Halo currents could be reduced by 60% and, using argon/deuterium and neon/deuterium gas mixtures, runaway electron generation could be avoided. Most objectives of the ITER-like ICRH antenna have been demonstrated; matching with closely packed straps, ELM resilience, scattering matrix arc detection and operation at high power density (6.2 MW m-2) and antenna strap voltages (42 kV). Coupling measurements are in very good agreement with TOPICA modelling. © 2011 IAEA, Vienna.
|
|
| 2. |
- Abel, I, et al.
(författare)
-
Overview of the JET results with the ITER-like wall
- 2013
-
Ingår i: Nuclear Fusion. - : IOP Publishing. - 1741-4326 .- 0029-5515. ; 53:10, s. 104002-
-
Tidskriftsartikel (refereegranskat)abstract
- Following the completion in May 2011 of the shutdown for the installation of the beryllium wall and the tungsten divertor, the first set of JET campaigns have addressed the investigation of the retention properties and the development of operational scenarios with the new plasma-facing materials. The large reduction in the carbon content (more than a factor ten) led to a much lower Z(eff) (1.2-1.4) during L- and H-mode plasmas, and radiation during the burn-through phase of the plasma initiation with the consequence that breakdown failures are almost absent. Gas balance experiments have shown that the fuel retention rate with the new wall is substantially reduced with respect to the C wall. The re-establishment of the baseline H-mode and hybrid scenarios compatible with the new wall has required an optimization of the control of metallic impurity sources and heat loads. Stable type-I ELMy H-mode regimes with H-98,H-y2 close to 1 and beta(N) similar to 1.6 have been achieved using gas injection. ELM frequency is a key factor for the control of the metallic impurity accumulation. Pedestal temperatures tend to be lower with the new wall, leading to reduced confinement, but nitrogen seeding restores high pedestal temperatures and confinement. Compared with the carbon wall, major disruptions with the new wall show a lower radiated power and a slower current quench. The higher heat loads on Be wall plasma-facing components due to lower radiation made the routine use of massive gas injection for disruption mitigation essential.
|
|
| 3. |
- Rieth, M., et al.
(författare)
-
A brief summary of the progress on the EFDA tungsten materials program
- 2013
-
Ingår i: Journal of Nuclear Materials. - : Elsevier BV. - 0022-3115 .- 1873-4820. ; 442:1-3, s. S173-S180
-
Tidskriftsartikel (refereegranskat)abstract
- The long-term objective of the European Fusion Development Agreement (EFDA) fusion materials programme is to develop structural and armor materials in combination with the necessary production and fabrication technologies for reactor concepts beyond the International Thermonuclear Experimental Reactor. The programmatic roadmap is structured into four engineering research lines which comprise fabrication process development, structural material development, armor material optimization, and irradiation performance testing, which are complemented by a fundamental research programme on "Materials Science and Modeling." This paper presents the current research status of the EFDA experimental and testing investigations, and gives a detailed overview of the latest results on materials research, fabrication, joining, high heat flux testing, plasticity studies, modeling, and validation experiments.
|
|
| 4. |
- Rieth, M., et al.
(författare)
-
Recent progress in research on tungsten materials for nuclear fusion applications in Europe
- 2013
-
Ingår i: Journal of Nuclear Materials. - : Elsevier BV. - 0022-3115 .- 1873-4820. ; 432:1-3, s. 482-500
-
Forskningsöversikt (refereegranskat)abstract
- The current magnetic confinement nuclear fusion power reactor concepts going beyond ITER are based on assumptions about the availability of materials with extreme mechanical, heat, and neutron load capacity. In Europe, the development of such structural and armour materials together with the necessary production, machining, and fabrication technologies is pursued within the EFDA long-term fusion materials programme. This paper reviews the progress of work within the programme in the area of tungsten and tungsten alloys. Results, conclusions, and future projections are summarized for each of the programme's main subtopics, which are: (1) fabrication, (2) structural W materials, (3) W armour materials, and (4) materials science and modelling. It gives a detailed overview of the latest results on materials research, fabrication processes, joining options, high heat flux testing, plasticity studies, modelling, and validation experiments.
|
|
| 5. |
|
|
| 6. |
|
|
| 7. |
|
|
| 8. |
- Röthlisberger, André, et al.
(författare)
-
Investigating the mechanism of collective bidirectional growth of carbon nanofiber carpets on metallic substrates
- 2013
-
Ingår i: Carbon. - : Elsevier BV. - 0008-6223 .- 1873-3891. ; 63, s. 498-507
-
Tidskriftsartikel (refereegranskat)abstract
- Bidirectional-growth of carbon nanofibers is a rare phenomenon found on free-standing catalyst particles, in contrast to the most commonly studied tip- and base-growth mechanisms for carbon nanostructures synthesized through thermal chemical vapor deposition. We reveal the underlying mechanisms of collective bidirectional growth in Ni x Pd 1-x -catalyzed carbon nanofiber carpets grown on a palladium substrate with varying nickel film thickness by monitoring the fiber growth evolution. The results show that the collective bidirectional growth is promoted and controlled by the chemical and physical restructuring of the sub-surface portion of the metal stack which undergoes micro-fragmentation as a result of the incorporation, diffusion, and precipitation of carbon. Carbon nanofiber growth can be controlled by engineering the catalyst-underlayer materials properties such as grain size, chemical composition and alloying. Since the determining factor whether carbon nanofibers or nanotubes are obtained is a strong function of catalyst size, the understanding of this growth mechanism can be transferred to the field of carbon nanotube synthesis. By keeping the grain size small enough to ensure carbon nanotube instead of carbon nanofiber growth, achieving dense, vertically aligned carbon nanotube carpets on metallic substrates might be possible, which is a prerequisite for carbon nanotube integration in integrated circuits.
|
|
| 9. |
- Velroyen, A., et al.
(författare)
-
Microbubbles as a scattering contrast agent for grating-based x-ray dark-field imaging
- 2013
-
Ingår i: Physics in Medicine and Biology. - 1361-6560. ; 58:4, s. 37-46
-
Tidskriftsartikel (refereegranskat)abstract
- In clinically established-absorption-based-biomedical x-ray imaging, contrast agents with high atomic numbers (e.g. iodine) are commonly used for contrast enhancement. The development of novel x-ray contrast modalities such as phase contrast and dark-field contrast opens up the possible use of alternative contrast media in x-ray imaging. We investigate using ultrasound contrast agents, which unlike iodine-based contrast agents can also be administered to patients with renal impairment and thyroid dysfunction, for application with a recently developed novel x-ray dark-field imaging modality. To produce contrast from these microbubble-based contrast agents, our method exploits ultra-small-angle coherent x-ray scattering. Such scattering dark-field x-ray images can be obtained with a grating-based x-ray imaging setup, together with refraction-based differential phase-contrast and the conventional attenuation contrast images. In this work we specifically show that ultrasound contrast agents based on microbubbles can be used to produce strongly enhanced dark-field contrast, with superior contrast-to-noise ratio compared to the attenuation signal. We also demonstrate that this method works well with an x-ray tube-based setup and that the relative contrast gain even increases when the pixel size is increased from tenths of microns to clinically compatible detector resolutions about up to a millimetre.
|
|
