| 1. |
- Bentham, James, et al.
(författare)
-
A century of trends in adult human height
- 2016
-
Ingår i: eLIFE. - 2050-084X. ; 5
-
Tidskriftsartikel (refereegranskat)abstract
- Being taller is associated with enhanced longevity, and higher education and earnings. We reanalysed 1472 population-based studies, with measurement of height on more than 18.6 million participants to estimate mean height for people born between 1896 and 1996 in 200 countries. The largest gain in adult height over the past century has occurred in South Korean women and Iranian men, who became 20.2 cm (95% credible interval 17.522.7) and 16.5 cm (13.319.7) taller, respectively. In contrast, there was little change in adult height in some sub-Saharan African countries and in South Asia over the century of analysis. The tallest people over these 100 years are men born in the Netherlands in the last quarter of 20th century, whose average heights surpassed 182.5 cm, and the shortest were women born in Guatemala in 1896 (140.3 cm; 135.8144.8). The height differential between the tallest and shortest populations was 19-20 cm a century ago, and has remained the same for women and increased for men a century later despite substantial changes in the ranking of countries.
|
|
| 2. |
- Bentham, James, et al.
(författare)
-
A century of trends in adult human height
- 2016
-
Ingår i: eLIFE. - : eLife Sciences Publications Ltd. - 2050-084X. ; 5
-
Tidskriftsartikel (refereegranskat)abstract
- Being taller is associated with enhanced longevity, and higher education and earnings. We reanalysed 1472 population-based studies, with measurement of height on more than 18.6 million participants to estimate mean height for people born between 1896 and 1996 in 200 countries. The largest gain in adult height over the past century has occurred in South Korean women and Iranian men, who became 20.2 cm (95% credible interval 17.5–22.7) and 16.5 cm (13.3– 19.7) taller, respectively. In contrast, there was little change in adult height in some sub-Saharan African countries and in South Asia over the century of analysis. The tallest people over these 100 years are men born in the Netherlands in the last quarter of 20th century, whose average heights surpassed 182.5 cm, and the shortest were women born in Guatemala in 1896 (140.3 cm; 135.8– 144.8). The height differential between the tallest and shortest populations was 19-20 cm a century ago, and has remained the same for women and increased for men a century later despite substantial changes in the ranking of countries.
|
|
| 3. |
- Bixby, H., et al.
(författare)
-
Rising rural body-mass index is the main driver of the global obesity epidemic in adults
- 2019
-
Ingår i: Nature. - : Springer Science and Business Media LLC. - 0028-0836 .- 1476-4687. ; 569:7755, s. 260-4
-
Tidskriftsartikel (refereegranskat)abstract
- Body-mass index (BMI) has increased steadily in most countries in parallel with a rise in the proportion of the population who live in cities(.)(1,2) This has led to a widely reported view that urbanization is one of the most important drivers of the global rise in obesity(3-6). Here we use 2,009 population-based studies, with measurements of height and weight in more than 112 million adults, to report national, regional and global trends in mean BMI segregated by place of residence (a rural or urban area) from 1985 to 2017. We show that, contrary to the dominant paradigm, more than 55% of the global rise in mean BMI from 1985 to 2017-and more than 80% in some low- and middle-income regions-was due to increases in BMI in rural areas. This large contribution stems from the fact that, with the exception of women in sub-Saharan Africa, BMI is increasing at the same rate or faster in rural areas than in cities in low- and middle-income regions. These trends have in turn resulted in a closing-and in some countries reversal-of the gap in BMI between urban and rural areas in low- and middle-income countries, especially for women. In high-income and industrialized countries, we noted a persistently higher rural BMI, especially for women. There is an urgent need for an integrated approach to rural nutrition that enhances financial and physical access to healthy foods, to avoid replacing the rural undernutrition disadvantage in poor countries with a more general malnutrition disadvantage that entails excessive consumption of low-quality calories.
|
|
| 4. |
|
|
| 5. |
|
|
| 6. |
|
|
| 7. |
- Zhou, Bin, et al.
(författare)
-
Worldwide trends in diabetes since 1980: A pooled analysis of 751 population-based studies with 4.4 million participants
- 2016
-
Ingår i: The Lancet. - : Elsevier B.V.. - 0140-6736 .- 1474-547X. ; 387:10027, s. 1513-1530
-
Tidskriftsartikel (refereegranskat)abstract
- Background: One of the global targets for non-communicable diseases is to halt, by 2025, the rise in the age standardised adult prevalence of diabetes at its 2010 levels. We aimed to estimate worldwide trends in diabetes, how likely it is for countries to achieve the global target, and how changes in prevalence, together with population growth and ageing, are aff ecting the number of adults with diabetes.Methods: We pooled data from population-based studies that had collected data on diabetes through measurement of its biomarkers. We used a Bayesian hierarchical model to estimate trends in diabetes prevalence-defined as fasting plasma glucose of 7.0 mmol/L or higher, or history of diagnosis with diabetes, or use of insulin or oral hypoglycaemic drugs-in 200 countries and territories in 21 regions, by sex and from 1980 to 2014. We also calculated the posterior probability of meeting the global diabetes target if post-2000 trends continue.Findings: We used data from 751 studies including 4372000 adults from 146 of the 200 countries we make estimates for. Global age-standardised diabetes prevalence increased from 4.3% (95% credible interval 2.4-17.0) in 1980 to 9.0% (7.2-11.1) in 2014 in men, and from 5.0% (2.9-7.9) to 7.9% (6.4-9.7) in women. The number of adults with diabetes in the world increased from 108 million in 1980 to 422 million in 2014 (28.5% due to the rise in prevalence, 39.7% due to population growth and ageing, and 31.8% due to interaction of these two factors). Age-standardised adult diabetes prevalence in 2014 was lowest in northwestern Europe, and highest in Polynesia and Micronesia, at nearly 25%, followed by Melanesia and the Middle East and north Africa. Between 1980 and 2014 there was little change in age-standardised diabetes prevalence in adult women in continental western Europe, although crude prevalence rose because of ageing of the population. By contrast, age-standardised adult prevalence rose by 15 percentage points in men and women in Polynesia and Micronesia. In 2014, American Samoa had the highest national prevalence of diabetes (>30% in both sexes), with age-standardised adult prevalence also higher than 25% in some other islands in Polynesia and Micronesia. If post-2000 trends continue, the probability of meeting the global target of halting the rise in the prevalence of diabetes by 2025 at the 2010 level worldwide is lower than 1% for men and is 1% for women. Only nine countries for men and 29 countries for women, mostly in western Europe, have a 50% or higher probability of meeting the global target.Interpretation: Since 1980, age-standardised diabetes prevalence in adults has increased, or at best remained unchanged, in every country. Together with population growth and ageing, this rise has led to a near quadrupling of the number of adults with diabetes worldwide. The burden of diabetes, both in terms of prevalence and number of adults aff ected, has increased faster in low-income and middle-income countries than in high-income countries.
|
|
| 8. |
- Bjork, Jonas, et al.
(författare)
-
Corrected capability studies with asymmetrical tolerances
- 2019
-
Ingår i: Quality Engineering. - : Informa UK Limited. - 1532-4222 .- 0898-2112. ; 31:4, s. 606-614
-
Tidskriftsartikel (refereegranskat)abstract
- The quality assurance of dimensions with asymmetric tolerances is as important as for dimensions with symmetric tolerances. A number of methods for calculating corrected capability indices for dimensions with asymmetric tolerances have been suggested, of which all but one involves reassigning the tolerances to become symmetric. As tolerances should be specified in the design phase, not the quality assurance phase the logic of this is flawed. The methods suggested in this article result in the same values for corrected capability as the previously suggested method that does not change the tolerances. This does not mean that one of the two methods are redundant; depending on preference and to some degree the form the data is presented in suggest one is preferred over the other. This article explains how the method suggested was derived and validates the result with computer generated data.
|
|
| 9. |
- Bohlin, Robert, 1972, et al.
(författare)
-
Data Flow and Communication Framework Supporting Digital Twin for Geometry Assurance
- 2018
-
Ingår i: ASME 2017 International Mechanical Engineering Congress and Exposition. ; 2
-
Konferensbidrag (refereegranskat)abstract
- Faster optimization algorithms, increased computer power and amount of available data, can leverage the area of simulation towards real-time control and optimization of products and production systems. This concept — often referred to as Digital Twin — enables real-time geometry assurance and allows moving from mass production to more individualized production. To master the challenges of a Digital Twin for Geometry Assurance the project Smart Assembly 4.0 gathers Swedish researchers within product development, automation, virtual manufacturing, control theory, data analysis and machine learning. The vision of Smart Assembly 4.0 is the autonomous, self-optimizing robotized assembly factory, which maximizes quality and throughput, while keeping flexibility and reducing cost, by a sensing, thinking and acting strategy. The concept is based on active part matching and self-adjusting equipment which improves geometric quality without tightening the tolerances of incoming parts. The goal is to assemble products with higher quality than the incoming parts. The concept utilizes information about individual parts to be joined (sensing), selects the best combination of parts (thinking) and adjust locator positions, clamps, weld/rivet positions and sequences (acting). The project is ongoing, and this paper specifies and highlights the infrastructure, components and data flows necessary in the Digital Twin in order to realize Smart Assembly 4.0. The framework is generic, but the paper focuses on a spot weld station where two robots join two sheet metal parts in an adjustable fixture.
|
|
| 10. |
- Deng, Dunyong, et al.
(författare)
-
Microstructural Characterization of AS-Manufactured and Heat Treated Electron Beam Melted Inconel 718
- 2016
-
Ingår i: Materials Science and Technology 2016 (MS&T16). - Warrendale, PA : Association for Iron and Steel Technology, AISTECH. - 9781510833142 ; , s. 105-112
-
Konferensbidrag (refereegranskat)abstract
- As manufactured and heat treated electron beam melted Inconel 718 exhibit inhomogeneous grain morphologies, mainly equiaxed close to the surface and more elongated columnar grains in the bulk. Different processing settings i.e., contouring in the surface region and hatching in the bulk region are responsible for differences in grain morphologies and textures, which are characterized using the SEM techniques electron contrast channeling imagine (ECCI) and electron backscattering diffraction (EBSD). Niobium carbides prefer to nucleate at TiN and are found to be in the grain growth direction. Regarding processing conditions, defects, such as porosities and segregations are discussed, as well as differences in microstructure emphasizing on grain morphologies and precipitates with regards to heat treatment and hardness indentation.
|
|
