| 1. |
- Anastasopoulos, M., et al.
(författare)
-
Multi-Grid detector for neutron spectroscopy : Results obtained on time-of-flight spectrometer CNCS
- 2017
-
Ingår i: Journal of Instrumentation. - : IOP PUBLISHING LTD. - 1748-0221 .- 1748-0221. ; 12:4
-
Tidskriftsartikel (refereegranskat)abstract
- The Multi-Grid detector technology has evolved from the proof-of-principle and characterisation stages. Here we report on the performance of the Multi-Grid detector, the MG.CNCS prototype, which has been installed and tested at the Cold Neutron Chopper Spectrometer, CNCS at SNS. This has allowed a side-by-side comparison to the performance of 3He detectors on an operational instrument. The demonstrator has an active area of 0.2 m2. It is specifically tailored to the specifications of CNCS. The detector was installed in June 2016 and has operated since then, collecting neutron scattering data in parallel to the He-3 detectors of CNCS. In this paper, we present a comprehensive analysis of this data, in particular on instrument energy resolution, rate capability, background and relative efficiency. Stability, gamma-ray and fast neutron sensitivity have also been investigated. The effect of scattering in the detector components has been measured and provides input to comparison for Monte Carlo simulations. All data is presented in comparison to that measured by the 3He detectors simultaneously, showing that all features recorded by one detector are also recorded by the other. The energy resolution matches closely. We find that the Multi-Grid is able to match the data collected by 3He, and see an indication of a considerable advantage in the count rate capability. Based on these results, we are confident that the Multi-Grid detector will be capable of producing high quality scientific data on chopper spectrometers utilising the unprecedented neutron flux of the ESS.
|
|
| 2. |
- Imam, Mewlude, et al.
(författare)
-
Trimethylboron as Single-Source Precursor for Boron-Carbon Thin Film Synthesis by Plasma Chemical Vapor Deposition
- 2016
-
Ingår i: The Journal of Physical Chemistry C. - : American Chemical Society (ACS). - 1932-7447 .- 1932-7455. ; 120:38, s. 21990-21997
-
Tidskriftsartikel (refereegranskat)abstract
- Boron carbon (BxC) thin films are potential neutron converting layers for B-10-based neutron detectors. However, as common material choices for such detectors do not tolerate temperatures above 500 degrees C, a low temperature deposition route is required. Here, we study trimethylboron B(CH3)(3) (TMB) as a single-source precursor for the deposition of BxC thin films by plasma CVD using Ar plasma. The effect of plasma power, TMB/Ar flow ratio and total pressure, on the film composition, morphology, chemical bonding, and microstructures are investigated. Dense and boron-rich films (B/C = 1.9) are achieved at high TMB flow under a low total pressure and high plasma power, which rendered an approximate substrate temperature of similar to 300 degrees C. Films mainly contain B-C bonds with the presence of B-O and C-C, which is attributed to be the origin of formed amorphous carbon in the films. The high H content 15 +/- 5 at. %) is almost independent of deposition parameters and contributed to lower the film density (2.16 g/cm(3)). The plasma compositional analysis shows that the TMB molecule decomposes to mainly atomic H, C-2, BH, and CH. A plasma chemical model for the decomposition of TMB with BH and CH as the plausible film depositing species in the plasma is proposed.
|
|
| 3. |
- Imam, Mewlude, et al.
(författare)
-
Trimethylboron as single-source precursor for boron-carbonthin film synthesis by plasma chemical vapor deposition
- 2015
-
Annan publikation (övrigt vetenskapligt/konstnärligt)abstract
- Boron-carbon (BxC) thin films are potential neutron converting layers for 10B-based neutron detectors. However, as common material choices for such detectors do not tolerate temperature above 500°C, a low temperature deposition route is required for this application. Here we study trimethylboron B(CH3)3 (TMB) as a single-source precursor for the deposition of BxC thin films by plasma CVD using Ar plasma. The effect of plasma power, TMB/Ar ratio and total pressure on the film composition, morphology and structure are investigated. The highest B/C ratio of 1.9 was achieved at high TMB flow in a low total pressure and high plasma power which rendered an approximate substrate temperature of ~ 300 °C. X-ray photoelectron spectroscopy shows that B-C bonds prevail in the films, although C-C and B-O bonds are also present. Raman spectroscopy confirms the presence of amorphous carbon phases in the films. The H content in the films is found to be 15±5 at. % by the time of flight elastic recoil detection analysis (Tof-ERDA). The film density as determined from X-ray reflectivity (XRR) measurements is 2. 16 ± 0.01 g/cm3 and the internal compressive stresses are measured to be less than 400 MPa.
|
|
| 4. |
- Kalman, Janos L, et al.
(författare)
-
Investigating polygenic burden in age at disease onset in bipolar disorder: Findings from an international multicentric study.
- 2019
-
Ingår i: Bipolar disorders. - : Wiley. - 1399-5618 .- 1398-5647. ; 21:1, s. 68-75
-
Tidskriftsartikel (refereegranskat)abstract
- Bipolar disorder (BD) with early disease onset is associated with an unfavorable clinical outcome and constitutes a clinically and biologically homogenous subgroup within the heterogeneous BD spectrum. Previous studies have found an accumulation of early age at onset (AAO) in BD families and have therefore hypothesized that there is a larger genetic contribution to the early-onset cases than to late onset BD. To investigate the genetic background of this subphenotype, we evaluated whether an increased polygenic burden of BD- and schizophrenia (SCZ)-associated risk variants is associated with an earlier AAO in BD patients.A total of 1995 BD type 1 patients from the Consortium of Lithium Genetics (ConLiGen), PsyCourse and Bonn-Mannheim samples were genotyped and their BD and SCZ polygenic risk scores (PRSs) were calculated using the summary statistics of the Psychiatric Genomics Consortium as a training data set. AAO was either separated into onset groups of clinical interest (childhood and adolescence [≤18years] vs adulthood [>18years]) or considered as a continuous measure. The associations between BD- and SCZ-PRSs and AAO were evaluated with regression models.BD- and SCZ-PRSs were not significantly associated with age at disease onset. Results remained the same when analyses were stratified by site of recruitment.The current study is the largest conducted so far to investigate the association between the cumulative BD and SCZ polygenic risk and AAO in BD patients. The reported negative results suggest that such a polygenic influence, if there is any, is not large, and highlight the importance of conducting further, larger scale studies to obtain more information on the genetic architecture of this clinically relevant phenotype.
|
|
| 5. |
- Schmidt, Susann, et al.
(författare)
-
Low-temperature growth of boron carbide coatings by direct current magnetron sputtering and high-power impulse magnetron sputtering
- 2016
-
Ingår i: Journal of Materials Science. - New York : Springer Science and Business Media LLC. - 0022-2461 .- 1573-4803. ; 51:23, s. 10418-10428
-
Tidskriftsartikel (refereegranskat)abstract
- B4C coatings for 10B-based neutron detector applications were deposited using high-power impulse magnetron sputtering (HiPIMS) and direct current magnetron sputtering (DCMS) processes. The coatings were deposited on Si(001) as well as on flat and macrostructured (grooved) Al blades in an industrial coating unit using B4C compound targets in Ar. The HiPIMS and DCMS processes were conducted at substrate temperatures of 100 and 400 °C and the Ar pressure was varied between 300 and 800 mPa. Neutron detector-relevant coating characterization was performed and the coating properties were evaluated with regard to their growth rate, density, level of impurities, and residual coating stress. The coating properties are mainly influenced by general process parameters such as the Ar pressure and substrate temperature. The deposition mode shows only minor effects on the coating quality and no effects on the step coverage. At a substrate temperature of 100 °C and an Ar pressure of 800 mPa, well-adhering and functional coatings were deposited in both deposition modes; the coatings showed a density of 2.2 g/cm3, a B/C ratio of ~3.9, and the lowest compressive residual stresses of 180 MPa. The best coating quality was obtained in DCMS mode using an Ar pressure of 300 mPa and a substrate temperature of 400 °C. Such process parameters yielded coatings with a slightly higher density of 2.3 g/cm3, a B/C ratio of ~4, and the compressive residual stresses limited to 220 MPa.
|
|
| 6. |
-
- 2019
-
Tidskriftsartikel (refereegranskat)
|
|
| 7. |
- Bakoglidis, Konstantinos D., et al.
(författare)
-
Low-temperature growth of low friction wear-resistant amorphous carbon nitride thin films by mid-frequency, high power impulse, and direct current magnetron sputtering
- 2015
-
Ingår i: Journal of Vacuum Science & Technology. A. Vacuum, Surfaces, and Films. - : American Vacuum Society. - 0734-2101 .- 1520-8559. ; 33:5
-
Tidskriftsartikel (refereegranskat)abstract
- Amorphous carbon nitride (a-CNx) thin films were deposited on steel AISI52100 and Si(001) substrates using mid-frequency magnetron sputtering (MFMS) with an MF bias voltage, high power impulse magnetron sputtering (HiPIMS) with a synchronized HiPIMS bias voltage, and direct current magnetron sputtering (DCMS) with a DC bias voltage. The films were deposited at a low substrate temperature of 150 °C and a N2/Ar flow ratio of 0.16 at the total pressure of 400 mPa. The negative bias voltage (Vs) was varied from 20 V to 120 V in each of the three deposition modes. The microstructure of the films was characterized by high-resolution transmission electron microscopy (HRTEM) and selected area electron diffraction (SAED), while the film morphology was investigated by scanning electron microscopy (SEM). All films possessed amorphous microstructure with clearly developed columns extending throughout the entire film thickness. Layers grown with the lowest substrate bias of 20 V exhibited pronounced intercolumnar porosity, independent of the technique used. Voids closed and dense films formed at Vs ≥ 60 V, Vs ≥ 100 V and Vs = 120 V for MFMS, DCMS and HiPIMS, respectively. X-ray photoelectron spectroscopy (XPS) revealed that the nitrogen-to-carbon ratio, N/C, of the films ranged between 0.2 and 0.24. Elastic recoil detection analysis (ERDA) showed that Ar content varied between 0 and 0.8 at% and increases as a function of Vs for all deposition techniques. All films exhibited compressive residual stress, σ, which depends on the growth method; HiPIMS produces the least stressed films with stress between – 0.4 and – 1.2 GPa for all Vs values, while for CNx films deposited by MFMS σ = – 4.2 GPa. Nanoindentation showed a significant increase in film hardness and reduced elastic modulus with increasing Vs for all techniques. The harder films were produced by MFMS with hardness as high as 25 GPa. Low friction coefficients, between 0.05 and 0.06, were recorded for all films. Furthermore, CNx films produced by MFMS and DCMS at Vs = 100 V and 120 V presented a high wear resistance with wear coefficients of k ≤ 2.3 x 10-5 mm3/Nm.
|
|
| 8. |
- Bohli, Jens-Mathias, et al.
(författare)
-
Selective Decryption of Outsourced IoT Data
- 2015
-
Ingår i: 2015 IEEE 2nd World Forum on Internet of Things (WF-IoT). - Piscataway, NJ : IEEE Communications Society. ; , s. 739-744
-
Konferensbidrag (refereegranskat)abstract
- Outsourcing of IoT-data is a common concept when using third-party services, e.g. an external building management service is given access to the building's sensor measurements. However, the measurements captured from building systems often need to be protected from unauthorized access, because they are linked to persons, processes or business secrets, and therefore data protection requirements apply. Nevertheless, due to the large data volumes, external storage is desirable from a business perspective. We propose the concept of a Security Broker based on symmetric encryption schemes. It offers a key management scheme to flexibly create short decryption keys for time intervals or specific ranges of measurement values. We further show how the scheme can be generalized or a combination of the schemes can be applied. We implemented a prototype in Java and analyzed its performance. The evaluation proved the mechanism's applicability for mainstream applications running on off-the-shelf computing equipment.
|
|
| 9. |
- Bouyoucef, S E, et al.
(författare)
-
Poster Session 2 : Monday 4 May 2015, 08
- 2015
-
Ingår i: European Heart Journal Cardiovascular Imaging. - : Oxford University Press (OUP). - 2047-2404 .- 2047-2412. ; 16 Suppl 1
-
Tidskriftsartikel (refereegranskat)
|
|
| 10. |
- Böttner, Christoph, et al.
(författare)
-
Pockmarks in the Witch Ground Basin, Central North Sea
- 2019
-
Ingår i: Geochemistry Geophysics Geosystems. - 1525-2027. ; 20:4, s. 1698-1719
-
Tidskriftsartikel (refereegranskat)abstract
- Marine sediments host large amounts of methane (CH4), which is a potent greenhouse gas. Quantitative estimates for methane release from marine sediments are scarce, and a poorly constrained temporal variability leads to large uncertainties in methane emission scenarios. Here, we use 2-D and 3-D seismic reflection, multibeam bathymetric, geochemical, and sedimentological data to (I) map and describe pockmarks in the Witch Ground Basin (central North Sea), (II) characterize associated sedimentological and fluid migration structures, and (III) analyze the related methane release. More than 1,500 pockmarks of two distinct morphological classes spread over an area of 225 km(2). The two classes form independently from another and are corresponding to at least two different sources of fluids. Class 1 pockmarks are large in size (> 6 m deep, > 250 m long, and > 75 m wide), show active venting, and are located above vertical fluid conduits that hydraulically connect the seafloor with deep methane sources. Class 2 pockmarks, which comprise 99.5% of all pockmarks, are smaller (0.9-3.1 m deep, 26-140 m long, and 14-57 m wide) and are limited to the soft, fine-grained sediments of the Witch Ground Formation and possibly sourced by compaction-related dewatering. Buried pockmarks within the Witch Ground Formation document distinct phases of pockmark formation, likely triggered by external forces related to environmental changes after deglaciation. Thus, greenhouse gas emissions from pockmark fields cannot be based on pockmark numbers and present-day fluxes but require an analysis of the pockmark forming processes through geological time. Plain Language Summary Marine sediments host large amounts of methane (CH4), which is a potent greenhouse gas. The amount of methane released into the atmosphere is, however, largely unknown making it difficult to implement this methane source in climate models. Here we use geophysical, geochemical, and sedimentological data to map the distribution of fluid escape structures in the central North Sea. More than 1,500 pockmarks, which are circular to semicircular depressions of the seafloor, indicate fluid flow from the subsurface. There are two distinct morphological classes of pockmarks corresponding to at least two different fluid sources. Class 1 pockmarks are large, show active venting, and are located above vertical fluid conduits in the subsurface, which feed fluids from deeper strata. Class 2 pockmarks, which comprise 99.5% of all pockmarks, are smaller and limited to the soft sediments directly below the seafloor. Older pockmarks in the subsurface document distinct phases of pockmark formation, likely triggered by external forces after the retreat of ice in the North Sea. The amount of methane released from natural geological sources based on pockmark numbers may be wrong as these do not take into account the origin and composition of released fluids.
|
|
