| 1. |
- Bogdanoff, Toni, et al.
(författare)
-
On the combined effects of surface quality and pore size on the fatigue life of Al–7Si–3Cu–Mg alloy castings
- 2023
-
Ingår i: Materials Science & Engineering. - : Elsevier. - 0921-5093 .- 1873-4936. ; 885
-
Tidskriftsartikel (refereegranskat)abstract
- This study has aimed to determine the effects of surface quality and pore size, obtained by different levels of hydrogen content of the liquid metal, on the fatigue behavior of an Al–7%Si–3%Cu–Mg casting alloy. Three surface conditions have been studied: as-cast rough, as-cast smooth, and standard machined and polished surface. The S–N curves have shown that surface roughness and hydrogen content individually impact fatigue strength. Surprisingly, the fatigue strength of machined and polished samples, which aligns with standard testing practices, is significantly reduced, compared to other conditions. Fatigue cracks have been observed to initiate at the pores just below the as-cast surface or on the machined surfaces. In all cases, pores have been observed to be surrounded by bifilms. Moreover, hydrogen content and roughness of the as-cast surface have been found to interact to determine the fatigue performance. These findings necessitate a re-evaluation of fatigue testing procedures for cast aluminum components.
|
|
| 2. |
- Bogdanoff, Toni, et al.
(författare)
-
On the Effectiveness of Rotary Degassing of Recycled Al-Si Alloy Melts : The Effect on Melt Quality and Energy Consumption for Melt Preparation
- 2023
-
Ingår i: Sustainability. - : MDPI. - 2071-1050. ; 15:6
-
Tidskriftsartikel (refereegranskat)abstract
- The effectiveness of rotary degassing on the defect formation and mechanical properties of the final casting of aluminium alloy EN AC 46000 was investigated, along with its impact on the energy consumption in the casting furnace. In the melt preparation prior to casting, the molten metal is usually transported from the melting furnace to the casting furnace with rotary degassing as a cleaning procedure. Under the conditions of this specific study, negligible degradation was observed in the mechanical properties of the final cast component in an aluminium EN AC 46000 alloy after removing the rotary degassing step in the process. Furthermore, removing the rotary degassing step led to a reduced temperature drop in the melt, thus minimizing the need for reheating (energy consumption) by up to 75% in the casting furnace. The reduced energy consumption was up to 124,000 kWh in yearly production in a 1500 kg casting furnace. The environmental impact showed a similar to 1500 kg reduction in CO2 for one 1500 kg electrical casting furnace in a year.
|
|
| 3. |
- Bogdanoff, Toni, et al.
(författare)
-
On the secondary cracks during crack propagation in an Al-Si-Cu-Mg alloy : An in-situ study
- 2023
-
Ingår i: Materials Characterization. - : Elsevier. - 1044-5803 .- 1873-4189. ; 203
-
Tidskriftsartikel (refereegranskat)abstract
- During in situ cyclic testing of hot isostatically pressed and heat-treated Al-5Si-0.5 Mg-1Cu alloy castings, cracks were observed to open up in places far away from the area of stress concentration. Cyclic testing was interrupted to assess these cracks. Analysis showed that these cracks originated from oxide bifilms that were entrained in the liquid state. Moreover, Si and Fe-rich intermetallics were observed to have precipitated on these bifilms. These finding makes it necessary to re-evaluate how damage is interpreted in mechanical studies. Entrainment damage, which takes place in the liquid state, may remain invisible in non-destructive inspection and can significantly affect fatigue properties when bifilms open up under low tensile stresses and present the propagating crack a path of low resistance during propagation.
|
|
| 4. |
- Bogdanoff, Toni, et al.
(författare)
-
The complex interaction between microstructural features and crack evolution during cyclic testing in heat-treated Al–Si–Mg–Cu cast alloys
- 2021
-
Ingår i: Materials Science & Engineering. - : Elsevier. - 0921-5093 .- 1873-4936. ; 825
-
Tidskriftsartikel (refereegranskat)abstract
- The study aimed to investigate crack initiation and propagation at the micro-scale in heat-treated Al–7Si–Mg cast alloys with different copper (Cu) contents. In-situ cyclic testing in a scanning electron microscope coupled with electron back-scattered diffraction and digital image correlation was used to evaluate the complex interaction between the crack path and the microstructural features. The three-nearest-neighbour distance of secondary particles was a new tool to describe the crack propagation in the alloys. The amount of Cu retained in the α-Al matrix after heat treatment increased with the Cu content in the alloy and enhanced the strength with a slight decrease in elongation. During cyclic testing, the two-dimensional (2D) crack path appeared with a mixed propagation, both trans- and inter-granular, regardless of the Cu content of the alloy. On fracture surfaces, multiple crack initiation points were detected along the thickness of the samples. The debonding of silicon (Si) particles took place during crack propagation in the Cu-free alloy, while cracking of Si particles and intermetallic phases occurred in the alloy with 3.2 wt% Cu. Three-dimensional tomography using focused ion beam revealed that the improved strength of the α-Al matrix changes the number of cracked particles ahead of the propagating crack with Cu concentration above 1.5 wt%.
|
|
| 5. |
- Bogdanoff, Toni
(författare)
-
The effect of microstructural features, defects and surface quality on the fatigue performance in Al-Si-Mg Cast alloys
- 2023
-
Doktorsavhandling (övrigt vetenskapligt/konstnärligt)abstract
- Global warming is driving industry to manufacture lighter components to reduce carbon dioxide (CO2) emissions. Promising candidates for achieving this are aluminium-silicon (Al-Si) cast alloys, which offer a high weight-to-strength ratio, excellent corrosion resistance, and good castability. However, understanding variations in the mechanical properties of these alloys is crucial to producing high-performance parts for critical applications. Defects and oxides are the primary reasons cast components in fatigue applications are rejected, as they negatively impact mechanical properties.A comprehensive understanding of the correlation between fatigue performance and parameters such as the α-aluminium matrix, Al-Si eutectic, surface roughness, porosities, hydrogen content, oxides, and intermetallic phases in Al-Si castings has not been reached.The research presented in this thesis used state-of-the-art experimental techniques to investigate the mechanical properties and crack-initiation and propagation behaviour of Al-Si-Mg cast alloy under cyclic loading. In-situ cyclic testing was conducted using scanning electron microscopy (SEM) combined with electron back-scattered diffraction (EBSD), digital image correlation (DIC), and focused ion beam (FIB) milling. These techniques enabled a comprehensive study of parameters affecting fatigue performance, including hydrogen content, surface roughness, oxides, and intermetallic phases. More specifically, we investigated the effect of melt quality, copper (Cu) content, oxide bifilms, surface quality, and porosity.The increased Cu concentration in heat-treated Al-Si alloys increased the amount of intermetallic phases, which affected the cracking behaviour. Furthermore, oxide bifilms were detected at crack-initiation sites, even in regions far away from the highly strained areas. Si- and Iron (Fe)-rich intermetallics were observed to have precipitated on these bifilms. Due to their very small size, these oxides are generally not detected by non-destructive inspections, but affect mechanical properties because they appear to open at relatively low tensile stresses. Finally, Al-Si alloy casting skins showed an interesting effect in terms of improving fatigue performance, highlighting the negative effect of surface polishing for such alloys.
|
|
| 6. |
- Bogdanoff, Toni, et al.
(författare)
-
The impact of HIP process and heat treatment on the mechanical behavior of an Al-Si-Mg alloy component
- 2023
-
Konferensbidrag (refereegranskat)abstract
- Castings generally contain pores and defects that can have a detrimental impact on mechanical properties. The hot isostatic pressing (HIP) process is usually applied to reduce internal porosities, which improves the mechanical properties because of the closed porosities. Therefore, this study investigates the effect of the HIP process on the mechanical properties of sand casting A356 aluminum alloys. This investigation was performed in collaboration with Unnaryd Modell, Quintus Technologies, and IAC Ankarsrum. Investigation of the complex interaction between the microstructural features on mechanical properties before and after the HIP process was examined using computed tomography scanning, in-situ cyclic testing, and scanning electron microscope. In the absence of large defects, the fatigue performance was improved. However, a significant variation in the result was found between the different conditions, whereas the coarser microstructure with larger porosities before the HIP process showed decreased ultimate tensile strength and elongation to failure. The samples tested under high cycle fatigue showed a reduced fatigue propagation zone in that the coarser microstructure. Moreover, large cleavage areas containing oxides in the fracture surfaces indicated that the HIP process closes all the porosities, but the oxide films are not creating a strong bonding. Furthermore, the samples tested under low cycle fatigue showed a difference in the crack propagation, whereas the coarser microstructure showed large cracks opened up away from the notch that assists the propagation leading to reduced fatigue life.
|
|
| 7. |
- Bogdanoff, Toni, et al.
(författare)
-
The impact of HIP process and heat treatment on the mechanical behaviour of an Al–Si–Mg alloy component
- 2024
-
Ingår i: International Journal of metalcasting. - : Springer. - 1939-5981 .- 2163-3193.
-
Tidskriftsartikel (refereegranskat)abstract
- This study investigates the effect of hot isostatic pressing (HIPping) on the static and fatigue properties of sand-casting A356 aluminium alloys. HIPping is a method to improve the fatigue properties in aluminium cast material by reducing or eliminating the inner porosities. Investigation of the complex interaction between the microstructural features on mechanical properties before and after the HIPping process was examined using computed tomography and scanning electron microscopy (SEM). Castings generally contain pores and defects that have a detrimental impact on the fatigue properties. The HIPping process closes the porosities in all investigated samples with an increase in density. Without significant defects, the mechanical performance improved in the finer microstructure. However, a considerable variation in the results was found between the different conditions, whereas the coarser microstructure with larger porosities before HIPping showed remarkably reduced results. The high-cycle fatigue-tested samples showed reduced fatigue propagation zone in the coarser microstructure. Moreover, large cleavage areas containing bifilms in the fracture surfaces indicate that the healing process of porosities is inefficient. These porosities are closed but not healed, resulting in a detrimental effect on the static and dynamic properties.
|
|
| 8. |
- Bogdanoff, Toni, et al.
(författare)
-
The influence of copper addition on crack initiation and propagation in an Al–Si–Mg alloy during cyclic testing
- 2020
-
Ingår i: Materialia. - : Elsevier. - 2589-1529. ; 12
-
Tidskriftsartikel (refereegranskat)abstract
- The effect of copper (Cu) addition up to 3.2 wt% on crack initiation and propagation in an Al–Si–Mg cast alloy was investigated using in-situ cyclic testing in the as-cast condition. A combination of digital image correlation, electron backscatter diffraction, and scanning electron microscopy was used to investigate crack initiation and propagation behaviour during in-situ cyclic testing. The results showed that Cu-rich intermetallic compounds with the addition of Cu up to 1.5 wt% do not affect the fatigue behaviour of these alloys, and that crack propagation in these cases is trans-granular and trans-dendritic. However, increasing the concentration of the Cu retained in the primary α-Al matrix in solid solution and Cu-containing precipitates delayed crack propagation during cyclic testing. The results showed that strain accumulation was highest at the grain boundaries; however, the crack preferred to propagate along or across primary α-Al dendrites due to the relatively lower mechanical strength of the matrix compared to the eutectic and intermetallic phases. Moreover, the addition of Cu of more than 3.0 wt% to Al-Si-Mg alloys changes the fatigue behaviour that a rapid failure occurs.
|
|
| 9. |
- Bogdanoff, Toni
(författare)
-
The influence of microstructure on the crack initiation and propagation in Al-Si casting alloys
- 2021
-
Licentiatavhandling (övrigt vetenskapligt/konstnärligt)abstract
- For reducing the CO2 footprint in many industrial fields, the goal is to produce lighter components. The aluminium-silicon (Al-Si) cast alloys are promising candidates to fulfill these goals with a high weight-to-strength ratio, good corrosion properties, excellent castability, and recyclable material. However, the variations within these components need to be understood to produce high-performance components for critical applications. The main reason for the rejection in these applications is defects and microstructural features that reduce the mechanical properties. The addition of copper (Cu) is one way of increasing the mechanical properties in Al-Si alloys and is commonly used in the automotive industry. Casting defects harm the mechanical properties, and these defects can be reduced by improving the melt quality, the correct design of the component, and the gating system.The study aims to investigate the static mechanical properties and the crack initiation and propagation under cyclic loading in an Al-7Si-Mg cast alloy with state-of-the-art experiments. The main focuses were on the effect of the HIP process and the role of Cu addition. In-situ cyclic testing using a scanning electron microscope coupled with electron back-scattered diffraction, digital image correlation, focused ion beam (FIB) slicing, and computed tomography scanning was used to evaluate the complex interaction between the crack path and the microstructural features.The amount of Cu retained in the α-Al matrix in as-cast and heat-treated conditions significantly influenced the static mechanical properties by increasing yield strength and ultimate tensile strength with a decrease in elongation. The three-nearest-neighbor distance of eutectic Si and Cu-rich particles and crack tortuosity were new tools to describe the crack propagation in the alloys, showing that a reduced distance between the Cu-rich phases is detrimental for the mechanical properties. Three dimensional tomography using a FIB revealed that the alloy with 3.2 wt.% Cu had a significantly increased quantity of cracked Si particles and intermetallic phases ahead of the crack tip than the Cu-free alloy. The effect of Cu and HIP process in this work shows the complex interaction between the microstructural features and the mechanical properties, and this needs to be considered to produce high-performance components.
|
|
| 10. |
- Ceschini, Lorella, et al.
(författare)
-
Effect of Cu addition on overaging behaviour, room and high temperature tensile and fatigue properties of A357 alloy
- 2020
-
Ingår i: Transactions of Nonferrous Metals Society of China. - : Elsevier. - 1003-6326 .- 2210-3384. ; 30:11, s. 2861-2878
-
Tidskriftsartikel (refereegranskat)abstract
- The aims of the present work are to evaluate the overaging behaviour of the investigated Cu-enriched alloy and to assess its mechanical behaviour, in terms of the tensile and fatigue strength, at room temperature and at 200 °C, and to correlate the mechanical performance with its microstructure, in particular with the secondary dendrite arm spacing (SDAS). The mechanical tests carried out on the overaged alloy at 200 °C indicate that the addition of about 1.3 wt.% Cu to the A357 alloy enables to maintain ultimate tensile strength and yield strength values close to 210 and 200 MPa, respectively, and fatigue strength at about 100 MPa. Compared to the quaternary (Al−Si−Cu−Mg) alloy C355, the A357−Cu alloy has greater mechanical properties at room temperature and comparable mechanical behaviour in the overaged condition at 200 °C. The microstructural analyses highlight that SDAS affects the mechanical behaviour of the peak-aged A357−Cu alloy at room temperature, while its influence is negligible on the tensile and fatigue properties of the overaged alloy at 200 °C.
|
|
