| 1. |
- Abdesselam, A., et al.
(författare)
-
Engineering for the ATLAS SemiConductor Tracker (SCT) end-cap
- 2008
-
Ingår i: Journal of Instrumentation. - 1748-0221 .- 1748-0221. ; 3
-
Tidskriftsartikel (refereegranskat)abstract
- The ATLAS SemiConductor Tracker (SCT) is a silicon-strip tracking detector which forms part of the ATLAS inner detector. The SCT is designed to track charged particles produced in proton-proton collisions at the Large Hadron Collider (LHC) at CERN at an energy of 14 TeV. The tracker is made up of a central barrel and two identical end-caps. The barrel contains 2112 silicon modules, while each end-cap contains 988 modules. The overall tracking performance depends not only on the intrinsic measurement precision of the modules but also on the characteristics of the whole assembly, in particular, the stability and the total material budget. This paper describes the engineering design and construction of the SCT end-caps, which are required to support mechanically the silicon modules, supply services to them and provide a suitable environment within the inner detector. Critical engineering choices are highlighted and innovative solutions are presented - these will be of interest to other builders of large-scale tracking detectors. The SCT end-caps will be fully connected at the start of 2008. Further commissioning will continue, to be ready for proton-proton collision data in 2008.
|
|
| 2. |
- Abdesselam, A., et al.
(författare)
-
The ATLAS semiconductor tracker end-cap module
- 2007
-
Ingår i: Nuclear Instruments and Methods in Physics Research Section A. - : Elsevier BV. - 0168-9002 .- 1872-9576. ; 575:3, s. 353-389
-
Tidskriftsartikel (refereegranskat)abstract
- The challenges for the tracking detector systems at the LHC are unprecedented in terms of the number of channels, the required read-out speed and the expected radiation levels. The ATLAS Semiconductor Tracker. (SCT) end-caps have a total of about 3 million electronics channels each reading out every 25 ns into its own on-chip 3.3 mu s buffer. The highest anticipated dose after 10 years operation is 1.4x10(14) cm(-2) in units of 1 MeV neutron equivalent (assuming the damage factors scale with the non-ionising energy loss). The forward tracker has 1976 double-sided modules, mostly of area similar to 70 cm(2), each having 2 x 768 strips read out by six ASICs per side. The requirement to achieve an average perpendicular radiation length of 1.5% X-0, while coping with up to 7 W dissipation per module (after irradiation), leads to stringent constraints on the thermal design. The additional requirement of 1500e(-) equivalent noise charge (ENC) rising to only 1800e(-) ENC after irradiation, provides stringent design constraints on both the high-density Cu/Polyimide flex read-out circuit and the ABCD3TA read-out ASICs. Finally, the accuracy of module assembly must not compromise the 16 mu m (r phi) resolution perpendicular to the strip directions or 580 mu m radial resolution coming from the 40 mrad front-back stereo angle. A total of 2210 modules were built to the tight tolerances and specifications required for the SCT. This was 234 more than the 1976 required and represents a yield of 93%. The component flow was at times tight, but the module production rate of 40-50 per week was maintained despite this. The distributed production was not found to be a major logistical problem and it allowed additional flexibility to take advantage of where the effort was available, including any spare capacity, for building the end-cap modules. The collaboration that produced the ATLAS SCT end-cap modules kept in close contact at all times so that the effects of shortages or stoppages at different sites could be rapidly resolved.
|
|
| 3. |
- Abdesselam, A., et al.
(författare)
-
The barrel modules of the ATLAS semiconductor tracker
- 2006
-
Ingår i: Nuclear Instruments and Methods in Physics Research Section A. - : Elsevier BV. - 0168-9002 .- 1872-9576. ; 568:2, s. 642-671
-
Tidskriftsartikel (refereegranskat)abstract
- This paper describes the silicon microstrip modules in the barrel section of the SemiConductor Tracker (SCT) of the ATLAS experiment at the CERN Large Hadron Collider (LHC). The module requirements, components and assembly techniques are given, as well as first results of the module performance on the fully assembled barrels that make up the detector being installed in the ATLAS experiment.
|
|
| 4. |
- Bruzzi, M, et al.
(författare)
-
Radiation-hard semiconductor detectors for SuperLHC
- 2005
-
Ingår i: Nuclear Instruments & Methods in Physics Research. Section A: Accelerators, Spectrometers, Detectors, and Associated Equipment. - : Elsevier BV. - 0167-5087 .- 0168-9002. ; 541:1-2, s. 189-201
-
Tidskriftsartikel (refereegranskat)abstract
- An option of increasing the luminosity of the Large Hadron Collider (LHC) at CERN to 1035 cm-2 s-1 has been envisaged to extend the physics reach of the machine. An efficient tracking down to a few centimetres from the interaction point will be required to exploit the physics potential of the upgraded LHC. As a consequence, the semiconductor detectors close to the interaction region will receive severe doses of fast hadron irradiation and the inner tracker detectors will need to survive fast hadron fluences of up to above 1016cm-2. The CERN-RD50 project "Development of Radiation Hard Semiconductor Devices for Very High Luminosity Colliders" has been established in 2002 to explore detector materials and technologies that will allow to operate devices up to, or beyond, this limit. The strategies followed by RD50 to enhance the radiation tolerance include the development of new or defect engineered detector materials (SiC, GaN, Czochralski and epitaxial silicon, oxygen enriched Float Zone silicon), the improvement of present detector designs and the understanding of the microscopic defects causing the degradation of the irradiated detectors. The latest advancements within the RD50 collaboration on radiation hard semiconductor detectors will be reviewed and discussed in this work.
|
|
| 5. |
- Wilson, J. A., et al.
(författare)
-
The optical links of the ATLAS SemiConductor tracker
- 2007
-
Ingår i: Journal of Instrumentation. - 1748-0221 .- 1748-0221. ; 2, s. 1-28
-
Tidskriftsartikel (refereegranskat)abstract
- Optical links are used for the readout of the 4088 silicon microstrip modules that make up the SemiConductor Tracker of the ATLAS experiment at the CERN Large Hadron Collider (LHC). The optical link requirements are reviewed, with particular emphasis on the very demanding environment at the LHC. The on-detector components have to operate in high radiation levels for 10 years, with no maintenance, and there are very strict requirements on power consumption, material and space. A novel concept for the packaging of the on-detector optoelectronics has been developed to meet these requirements. The system architecture, including its redundancy features, is explained and the critical on-detector components are described. The results of the extensive Quality Assurance performed during all steps of the assembly are discussed.
|
|
| 6. |
- Skeie, G., et al.
(författare)
-
Use of dietary supplements in the European Prospective Investigation into Cancer and Nutrition calibration study
- 2009
-
Ingår i: European Journal of Clinical Nutrition. - : Springer Science and Business Media LLC. - 1476-5640 .- 0954-3007. ; 63:4s, s. 226-238
-
Tidskriftsartikel (refereegranskat)abstract
- Background: Dietary supplement use is increasing, but there are few comparable data on supplement intakes and how they affect the nutrition and health of European consumers. The aim of this study was to describe the use of dietary supplements in subsamples of the 10 countries participating in the European Prospective Investigation into Cancer and Nutrition (EPIC). Methods: Specific questions on dietary supplement use were asked as a part of single 24-h recalls performed on 36 034 men and women aged 35-74 years from 1995 to 2000. Results: Between countries, the mean percentage of dietary supplement use varied almost 10-fold among women and even more among men. There was a clear north-south gradient in use, with a higher consumption in northern countries. The lowest crude mean percentage of use was found in Greece (2.0% among men, 6.7% among women), and the highest was in Denmark (51.0% among men, 65.8% among women). Use was higher in women than in men. Vitamins, minerals or combinations of them were the predominant types of supplements reported, but there were striking differences between countries. Conclusions: This study indicates that there are wide variations in supplement use in Europe, which may affect individual and population nutrient intakes. The results underline the need to monitor consumption of dietary supplements in Europe, as well as to evaluate the risks and benefits. European Journal of Clinical Nutrition (2009) 63, S226-S238; doi: 10.1038/ejcn.2009.83
|
|
| 7. |
- Klionsky, Daniel J., et al.
(författare)
-
Guidelines for the use and interpretation of assays for monitoring autophagy in higher eukaryotes
- 2008
-
Ingår i: Autophagy. - : Landes Bioscience. - 1554-8627 .- 1554-8635. ; 4:2, s. 151-175
-
Forskningsöversikt (refereegranskat)abstract
- Research in autophagy continues to accelerate,1 and as a result many new scientists are entering the field. Accordingly, it is important to establish a standard set of criteria for monitoring macroautophagy in different organisms. Recent reviews have described the range of assays that have been used for this purpose.2,3 There are many useful and convenient methods that can be used to monitor macroautophagy in yeast, but relatively few in other model systems, and there is much confusion regarding acceptable methods to measure macroautophagy in higher eukaryotes. A key point that needs to be emphasized is that there is a difference between measurements that monitor the numbers of autophagosomes versus those that measure flux through the autophagy pathway; thus, a block in macroautophagy that results in autophagosome accumulation needs to be differentiated from fully functional autophagy that includes delivery to, and degradation within, lysosomes (in most higher eukaryotes) or the vacuole (in plants and fungi). Here, we present a set of guidelines for the selection and interpretation of the methods that can be used by investigators who are attempting to examine macroautophagy and related processes, as well as by reviewers who need to provide realistic and reasonable critiques of papers that investigate these processes. This set of guidelines is not meant to be a formulaic set of rules, because the appropriate assays depend in part on the question being asked and the system being used. In addition, we emphasize that no individual assay is guaranteed to be the most appropriate one in every situation, and we strongly recommend the use of multiple assays to verify an autophagic response.
|
|
| 8. |
- Besson, H., et al.
(författare)
-
A cross-sectional analysis of physical activity and obesity indicators in European participants of the EPIC-PANACEA study
- 2009
-
Ingår i: International Journal of Obesity. - : Springer Science and Business Media LLC. - 1476-5497 .- 0307-0565. ; 33:4, s. 497-506
-
Tidskriftsartikel (refereegranskat)abstract
- Objectives: Cross-sectional data suggest a strong association between low levels of physical activity and obesity. The EPIC-PANACEA ( European Prospective Investigation into Cancer-Physical Activity, Nutrition, Alcohol, Cessation of Smoking, Eating out of home And obesity) project was designed to investigate the associations between physical activity and body mass index (BMI) and waist circumference based on individual data collected across nine European countries. Methods: In the European Prospective Investigation into Cancer and Nutrition ( EPIC), 519 931 volunteers were recruited between 1992 and 2000, of whom 405 819 had data on main variables of interest. Height, body weight and waist circumference were measured using standardized procedures. Physical activity was assessed using a validated four-category index reflecting a self-reported usual activity during work and leisure time. The associations between physical activity and BMI and waist circumference were estimated using multilevel mixed effects linear regression models, adjusted for age, total energy intake, smoking status, alcohol consumption and educational level. Results: A total of 125 629 men and 280 190 women with a mean age of 52.9 (s.d. 9.7) and 51.5 (s.d. 10.0) years, respectively were included. The mean BMI was 26.6 kg/m(2) (s.d. 3.6) in men and 25.0 kg/m(2) (s.d. 4.5) in women. Fifty percent of men and 30% of women were categorized as being active or moderately active. A one-category difference in the physical activity index was inversely associated with a difference of 0.18 kg/m(2) in the mean BMI (95% confidence interval, CI, 0.11, 0.24) and 1.04-cm (95% CI 0.82, 1.26) difference in waist circumference in men. The equivalent figures for women were 0.31 kg/m(2) (95% CI 0.23, 0.38) and 0.90 cm ( 95% CI 0.71, 1.08), respectively. Conclusions: Physical activity is inversely associated with both BMI and waist circumference across nine European countries. Although we cannot interpret the association causally, our results were observed in a large and diverse cohort independently from many potential confounders.
|
|
| 9. |
- Orfanos, P, et al.
(författare)
-
Eating out of home and its correlates in 10 European countries. The European Prospective Investigation into Cancer and Nutrition (EPIC) study
- 2007
-
Ingår i: Public Health Nutrition. - 1475-2727 .- 1368-9800. ; 10:12, s. 1515-1525
-
Tidskriftsartikel (refereegranskat)abstract
- OBJECTIVE: To compare the average out-of-home (OH) consumption of foods and beverages, as well as energy intake, among populations from 10 European countries and to describe the characteristics of substantial OH eaters, as defined for the purpose of the present study, in comparison to other individuals. DESIGN: Cross-sectional study. Dietary data were collected through single 24-hour dietary recalls, in which the place of consumption was recorded. For the present study, substantial OH eaters were defined as those who consumed more than 25% of total daily energy intake at locations other than the household premises. Mean dietary intakes and the proportion of substantial OH eaters are presented by food group and country. Logistic regression analyses were used to estimate the odds of being a substantial OH eater in comparison to not being one, using mutually adjusted possible non-dietary determinants. SETTING: Ten European countries participating in the European Prospective Investigation into Cancer and Nutrition (EPIC). SUBJECTS: The subjects were 34 270 individuals, 12 537 men and 21 733 women, aged 35-74 years. RESULTS: The fraction of energy intake during OH eating was generally higher in northern European countries than in the southern ones. Among the food and beverage groups, those selectively consumed outside the home were coffee/tea/waters and sweets and, to a lesser extent, cereals, meats, added lipids and vegetables. Substantial OH eating was positively associated with energy intake and inversely associated with age and physical activity. Substantial OH eating was less common among the less educated compared with the more educated, and more common during weekdays in central and north Europe and during the weekend in south Europe. CONCLUSIONS: Eating outside the home was associated with sedentary lifestyle and increased energy intake; it was more common among the young and concerned in particular coffee/tea/waters and sweets.
|
|
| 10. |
- Pischon, T., et al.
(författare)
-
General and Abdominal Adiposity and Risk of Death in Europe
- 2008
-
Ingår i: New England Journal of Medicine. - 0028-4793. ; 359:20, s. 2105-2120
-
Tidskriftsartikel (refereegranskat)abstract
- BACKGROUND Previous studies have relied predominantly on the body-mass index (BMI, the weight in kilograms divided by the square of the height in meters) to assess the association of adiposity with the risk of death, but few have examined whether the distribution of body fat contributes to the prediction of death. METHODS We examined the association of BMI, waist circumference, and waist-to-hip ratio with the risk of death among 359,387 participants from nine countries in the European Prospective Investigation into Cancer and Nutrition (EPIC). We used a Cox regression analysis, with age as the time variable, and stratified the models according to study center and age at recruitment, with further adjustment for educational level, smoking status, alcohol consumption, physical activity, and height. RESULTS During a mean follow-up of 9.7 years, 14,723 participants died. The lowest risks of death related to BMI were observed at a BMI of 25.3 for men and 24.3 for women. After adjustment for BMI, waist circumference and waist-to-hip ratio were strongly associated with the risk of death. Relative risks among men and women in the highest quintile of waist circumference were 2.05 (95% confidence interval [CI], 1.80 to 2.33) and 1.78 (95% CI, 1.56 to 2.04), respectively, and in the highest quintile of waist-to-hip ratio, the relative risks were 1.68 (95% CI, 1.53 to 1.84) and 1.51 (95% CI, 1.37 to 1.66), respectively. BMI remained significantly associated with the risk of death in models that included waist circumference or waist-to-hip ratio (P<0.001). CONCLUSIONS These data suggest that both general adiposity and abdominal adiposity are associated with the risk of death and support the use of waist circumference or waist-tohip ratio in addition to BMI in assessing the risk of death.
|
|
