| 1. |
|
|
| 2. |
|
|
| 3. |
|
|
| 4. |
|
|
| 5. |
- Stroth, U., et al.
(författare)
-
Progress from ASDEX Upgrade experiments in preparing the physics basis of ITER operation and DEMO scenario development
- 2022
-
Ingår i: Nuclear Fusion. - : IOP Publishing. - 1741-4326 .- 0029-5515. ; 62:4
-
Tidskriftsartikel (refereegranskat)abstract
- An overview of recent results obtained at the tokamak ASDEX Upgrade (AUG) is given. A work flow for predictive profile modelling of AUG discharges was established which is able to reproduce experimental H-mode plasma profiles based on engineering parameters only. In the plasma center, theoretical predictions on plasma current redistribution by a dynamo effect were confirmed experimentally. For core transport, the stabilizing effect of fast ion distributions on turbulent transport is shown to be important to explain the core isotope effect and improves the description of hollow low-Z impurity profiles. The L-H power threshold of hydrogen plasmas is not affected by small helium admixtures and it increases continuously from the deuterium to the hydrogen level when the hydrogen concentration is raised from 0 to 100%. One focus of recent campaigns was the search for a fusion relevant integrated plasma scenario without large edge localised modes (ELMs). Results from six different ELM-free confinement regimes are compared with respect to reactor relevance: ELM suppression by magnetic perturbation coils could be attributed to toroidally asymmetric turbulent fluctuations in the vicinity of the separatrix. Stable improved confinement mode plasma phases with a detached inner divertor were obtained using a feedback control of the plasma β. The enhanced D α H-mode regime was extended to higher heating power by feedback controlled radiative cooling with argon. The quasi-coherent exhaust regime was developed into an integrated scenario at high heating power and energy confinement, with a detached divertor and without large ELMs. Small ELMs close to the separatrix lead to peeling-ballooning stability and quasi continuous power exhaust. Helium beam density fluctuation measurements confirm that transport close to the separatrix is important to achieve the different ELM-free regimes. Based on separatrix plasma parameters and interchange-drift-Alfvén turbulence, an analytic model was derived that reproduces the experimentally found important operational boundaries of the density limit and between L- and H-mode confinement. Feedback control for the X-point radiator (XPR) position was established as an important element for divertor detachment control. Stable and detached ELM-free phases with H-mode confinement quality were obtained when the XPR was moved 10 cm above the X-point. Investigations of the plasma in the future flexible snow-flake divertor of AUG by means of first SOLPS-ITER simulations with drifts activated predict beneficial detachment properties and the activation of an additional strike point by the drifts.
|
|
| 6. |
- Hobirk, J., et al.
(författare)
-
The JET hybrid scenario in Deuterium, Tritium and Deuterium-Tritium
- 2023
-
Ingår i: Nuclear Fusion. - : Institute of Physics Publishing (IOPP). - 0029-5515 .- 1741-4326. ; 63:11
-
Tidskriftsartikel (refereegranskat)abstract
- The JET hybrid scenario has been developed from low plasma current carbon wall discharges to the record-breaking Deuterium-Tritium plasmas obtained in 2021 with the ITER-like Be/W wall. The development started in pure Deuterium with refinement of the plasma current, and toroidal magnetic field choices and succeeded in solving the heat load challenges arising from 37 MW of injected power in the ITER like wall environment, keeping the radiation in the edge and core controlled, avoiding MHD instabilities and reaching high neutron rates. The Deuterium hybrid plasmas have been re-run in Tritium and methods have been found to keep the radiation controlled but not at high fusion performance probably due to time constraints. For the first time this scenario has been run in Deuterium-Tritium (50:50). These plasmas were re-optimised to have a radiation-stable H-mode entry phase, good impurity control through edge Ti gradient screening and optimised performance with fusion power exceeding 10 MW for longer than three alpha particle slow down times, 8.3 MW averaged over 5 s and fusion energy of 45.8 MJ.
|
|
| 7. |
- Maslov, M., et al.
(författare)
-
JET D-T scenario with optimized non-thermal fusion
- 2023
-
Ingår i: Nuclear Fusion. - : Institute of Physics (IOP). - 0029-5515 .- 1741-4326. ; 63:11
-
Tidskriftsartikel (refereegranskat)abstract
- In JET deuterium-tritium (D-T) plasmas, the fusion power is produced through thermonuclear reactions and reactions between thermal ions and fast particles generated by neutral beam injection (NBI) heating or accelerated by electromagnetic wave heating in the ion cyclotron range of frequencies (ICRFs). To complement the experiments with 50/50 D/T mixtures maximizing thermonuclear reactivity, a scenario with dominant non-thermal reactivity has been developed and successfully demonstrated during the second JET deuterium-tritium campaign DTE2, as it was predicted to generate the highest fusion power in JET with a Be/W wall. It was performed in a 15/85 D/T mixture with pure D-NBI heating combined with ICRF heating at the fundamental deuterium resonance. In steady plasma conditions, a record 59 MJ of fusion energy has been achieved in a single pulse, of which 50.5 MJ were produced in a 5 s time window (P fus = 10.1 MW) with average Q = 0.33, confirming predictive modelling in preparation of the experiment. The highest fusion power in these experiments, P fus = 12.5 MW with average Q = 0.38, was achieved over a shorter 2 s time window, with the period of sustainment limited by high-Z impurity accumulation. This scenario provides unique data for the validation of physics-based models used to predict D-T fusion power.
|
|
| 8. |
- Olasz, S., et al.
(författare)
-
Runaway electron modelling in the EU-IM framework
- 2021
-
Ingår i: 47th EPS Conference on Plasma Physics, EPS 2021. - : European Physical Society (EPS). ; 2021-June, s. 1156-1159
-
Konferensbidrag (refereegranskat)abstract
- The Runaway Electron Test Workflow was used to study the behaviour of the Dreicer generation of runaway electrons in dynamic scenarios to find a parameter which can be used to determine the need of kinetic modelling in more complex simulations. It was found that for processes which vary faster than the collision time at the critical velocity for runaway electron generation, kinetic modelling is advised to capture potential kinetic effects. A more complex tool, the ETS have been used to simulate a self-consistent thermal quench induced by massive material injection with promising initial results. Development of ETS capabilities continues with introduction of kinetic modelling and moving onto the new ETS6 versions.
|
|
