| 1. |
|
|
| 2. |
|
|
| 3. |
|
|
| 4. |
|
|
| 5. |
- Hobirk, J., et al.
(författare)
-
The JET hybrid scenario in Deuterium, Tritium and Deuterium-Tritium
- 2023
-
Ingår i: Nuclear Fusion. - : Institute of Physics Publishing (IOPP). - 0029-5515 .- 1741-4326. ; 63:11
-
Tidskriftsartikel (refereegranskat)abstract
- The JET hybrid scenario has been developed from low plasma current carbon wall discharges to the record-breaking Deuterium-Tritium plasmas obtained in 2021 with the ITER-like Be/W wall. The development started in pure Deuterium with refinement of the plasma current, and toroidal magnetic field choices and succeeded in solving the heat load challenges arising from 37 MW of injected power in the ITER like wall environment, keeping the radiation in the edge and core controlled, avoiding MHD instabilities and reaching high neutron rates. The Deuterium hybrid plasmas have been re-run in Tritium and methods have been found to keep the radiation controlled but not at high fusion performance probably due to time constraints. For the first time this scenario has been run in Deuterium-Tritium (50:50). These plasmas were re-optimised to have a radiation-stable H-mode entry phase, good impurity control through edge Ti gradient screening and optimised performance with fusion power exceeding 10 MW for longer than three alpha particle slow down times, 8.3 MW averaged over 5 s and fusion energy of 45.8 MJ.
|
|
| 6. |
- Maslov, M., et al.
(författare)
-
JET D-T scenario with optimized non-thermal fusion
- 2023
-
Ingår i: Nuclear Fusion. - : Institute of Physics (IOP). - 0029-5515 .- 1741-4326. ; 63:11
-
Tidskriftsartikel (refereegranskat)abstract
- In JET deuterium-tritium (D-T) plasmas, the fusion power is produced through thermonuclear reactions and reactions between thermal ions and fast particles generated by neutral beam injection (NBI) heating or accelerated by electromagnetic wave heating in the ion cyclotron range of frequencies (ICRFs). To complement the experiments with 50/50 D/T mixtures maximizing thermonuclear reactivity, a scenario with dominant non-thermal reactivity has been developed and successfully demonstrated during the second JET deuterium-tritium campaign DTE2, as it was predicted to generate the highest fusion power in JET with a Be/W wall. It was performed in a 15/85 D/T mixture with pure D-NBI heating combined with ICRF heating at the fundamental deuterium resonance. In steady plasma conditions, a record 59 MJ of fusion energy has been achieved in a single pulse, of which 50.5 MJ were produced in a 5 s time window (P fus = 10.1 MW) with average Q = 0.33, confirming predictive modelling in preparation of the experiment. The highest fusion power in these experiments, P fus = 12.5 MW with average Q = 0.38, was achieved over a shorter 2 s time window, with the period of sustainment limited by high-Z impurity accumulation. This scenario provides unique data for the validation of physics-based models used to predict D-T fusion power.
|
|
| 7. |
- Kim, Hyun-Tae, et al.
(författare)
-
Validation of D-T fusion power prediction capability against 2021 JET D-T experiments
- 2023
-
Ingår i: Nuclear Fusion. - 0029-5515 .- 1741-4326. ; 63:11
-
Tidskriftsartikel (refereegranskat)abstract
- JET experiments using the fuel mixture envisaged for fusion power plants, deuterium and tritium (D-T), provide a unique opportunity to validate existing D-T fusion power prediction capabilities in support of future device design and operation preparation. The 2021 JET D-T experimental campaign has achieved D-T fusion powers sustained over 5 s in ITER-relevant conditions i.e. operation with the baseline or hybrid scenario in the full metallic wall. In preparation of the 2021 JET D-T experimental campaign, extensive D-T predictive modelling was carried out with several assumptions based on D discharges. To improve the validity of ITER D-T predictive modelling in the future, it is important to use the input data measured from 2021 JET D-T discharges in the present core predictive modelling, and to specify the accuracy of the D-T fusion power prediction in comparison with the experiments. This paper reports on the validation of the core integrated modelling with TRANSP, JINTRAC, and ETS coupled with a quasilinear turbulent transport model (Trapped Gyro Landau Fluid or QualLiKiz) against the measured data in 2021 JET D-T discharges. Detailed simulation settings and the heating and transport models used are described. The D-T fusion power calculated with the interpretive TRANSP runs for 38 D-T discharges (12 baseline and 26 hybrid discharges) reproduced the measured values within 20 % . This indicates the additional uncertainties, that could result from the measurement error bars in kinetic profiles, impurity contents and neutron rates, and also from the beam-thermal fusion reaction modelling, are less than 20 % in total. The good statistical agreement confirms that we have the capability to accurately calculate the D-T fusion power if correct kinetic profiles are predicted, and indicates that any larger deviation of the D-T fusion power prediction from the measured fusion power could be attributed to the deviation of the predicted kinetic profiles from the measured kinetic profiles in these plasma scenarios. Without any posterior adjustment of the simulation settings, the ratio of predicted D-T fusion power to the measured fusion power was found as 65%-96% for the D-T baseline and 81%-97% for D-T hybrid discharge. Possible reasons for the lower D-T prediction are discussed and future works to improve the fusion power prediction capability are suggested. The D-T predictive modelling results have also been compared to the predictive modelling of the counterpart D discharges, where the key engineering parameters are similar. Features in the predicted kinetic profiles of D-T discharges such as underprediction of ne are also found in the prediction results of the counterpart D discharges, and it leads to similar levels of the normalized neutron rate prediction between the modelling results of D-T and the counterpart D discharges. This implies that the credibility of D-T fusion power prediction could be a priori estimated by the prediction quality of the preparatory D discharges, which will be attempted before actual D-T experiments.
|
|
