| 1. |
- Wenman, M. R., et al.
(författare)
-
Modelling and experimental characterisation of a residual stress field in a ferritic compact tension specimen
- 2009
-
Ingår i: International Journal of Pressure Vessels and Piping. - : Elsevier BV. - 1879-3541 .- 0308-0161. ; 86:12, s. 830-837
-
Tidskriftsartikel (refereegranskat)abstract
- The aim of the work is to elucidate the influence of plasticity behaviour on the residual stress field in a ferritic reactor pressure vessel steel. To this end, we investigate two compressively pre-loaded compact tension (CT) specimens to generate a mechanical residual stress field. One specimen was subsequently pre-cracked by fatigue before both specimens were measured using high-energy synchrotron X-ray diffraction. A fine grain size microstructure (similar to 5-10 mu m grain size) allowed a small X-ray beam slit size and therefore gauge volume. The results provide an excellent data set for validation of finite element (FE) modelling predictions against which they have been compared. The results of both mechanical testing and modelling suggest that the use of a combined hardening model is needed to accurately predict the residual stress field present in the specimen after pre-loading. Some discrepancy between the modelled crack tip stress values and those found by X-ray diffraction remain which can be partly explained by volume averaging effects in the presence of very high stress/strain gradients. Crown Copyright (C) 2009 Published by Elsevier Ltd. All rights reserved.
|
|
| 2. |
- Colegrove, P., et al.
(författare)
-
Welding process impact on residual stress and distortion
- 2009
-
Ingår i: Science and Technology of Welding and Joining. - 1362-1718. ; 14:8, s. 717-725
-
Tidskriftsartikel (refereegranskat)abstract
- Residual stress and distortion continue to be important issues in shipbuilding and are still subject to large amounts of research. This paper demonstrates how the type of welding process influences the amount of distortion. Many shipyards currently use submerged arc welding (SAW) as their welding process of choice. In this manuscript, the authors compare welds made by SAW with DC gas metal arc welding, pulsed gas metal arc welding, Fronius cold metal transfer (CMT), autogenous laser and laser hybrid welding on butt welds in 4 mm thick DH36 ship plate. Laser and laser hybrid welding were found to produce the lowest distortion. Nevertheless, a considerable improvement can be achieved with the pulsed gas metal arc welding and CMT processes. The paper seeks to understand the relationship between heat input, fusion area, measured distortion and the residual stress predicted from a simple numerical model, and the residual stresses validated with experimental data.
|
|
| 3. |
- Lehmann, E. H., et al.
(författare)
-
The energy-selective option in neutron imaging
- 2009
-
Ingår i: Nuclear Instruments & Methods in Physics Research. Section A: Accelerators, Spectrometers, Detectors, and Associated Equipment. - : Elsevier BV. - 0167-5087 .- 0168-9002. ; 603:3, s. 429-438
-
Tidskriftsartikel (refereegranskat)abstract
- In the past, neutron imaging investigations have been mostly performed in "integrating mode", which averages over the full applied neutron energy spectrum. This article describes four different methods and devices of obtaining energy selectivity in the thermal to cold energy range, which allow a new approach in neutron imaging. Two principles have been used and tested: (a) selection of neutrons by suppression of contribution of other spectral parts; (b) using the flight-time information in distance from the source. For the (a) option, three different devices have been exploited practically. Information about material properties can be revealed that cannot be obtained in integrating mode. The energy-dependent transmission measurements make use of the Bragg edges in the total cross-sections of materials. Energy-selective radiography has vast potential for contrast variation, and for mapping structural properties such as crystallographic texture and residual strains with high spatial resolution. The obtained images highlight new opportunities in materials and engineering research, in comparison and complementary to what can be obtained by neutron scattering. There is likely to be an increasing need for implementing time-of-flight neutron imaging at present and future pulsed spallation sources, where the energy range can be selected almost without limitations. In this paper we attempt to give an overview over the current state of the art of energy-selective imaging and the experimental configurations required. (C) 2009 Elsevier B.V. All rights reserved.
|
|
