| 1. |
- Wang, Jianqiu, et al.
(författare)
-
A Comparative Study on Hole Transfer Inversely Correlated with Driving Force in Two Non-Fullerene Organic Solar Cells
- 2019
-
Ingår i: The Journal of Physical Chemistry Letters. - : AMER CHEMICAL SOC. - 1948-7185. ; 10:14, s. 4110-4116
-
Tidskriftsartikel (refereegranskat)abstract
- We report a faster rate of hole transfer under a smaller AHomo in a comparative study of two group organic solar cells (OSCs) consisting of IT-4F as an acceptor and PBDBT and PBDBT-SF as donors. In the OSCs based on PBDBT. SF:IT-4F, a higher short-circuit current (J(SC)) was observed with a Delta(Homo) of 0.31 eV compared to a lower Jsc in PBDBT:IT-4F OSCs with a larger Delta(Homo) (0.45 eV). Intensive investigation indicates that the rate of transfer of a hole from IT-4F to PBDBT-SF or PBDBT is inversely proportional to the Delta(Homo) between IT-4F and donors. The larger Jsc in the PBDBT-SF:IT-4F device is attributed to a synergy of faster hole transfer, slower recombination, and rapid charge extraction enabled by desired morphology and balanced charge carrier mobilities with PBDBT-SF, suggesting that under a sufficiently high Delta(Homo), comprehensive considerations of the transport, film morphology, and energy levels are needed when designing new materials for high-performance OSCs.
|
|
| 2. |
- Li, Yongxi, et al.
(författare)
-
A fused-ring based electron acceptor for efficient non-fullerene polymer solar cells with small HOMO offset
- 2016
-
Ingår i: NANO ENERGY. - : ELSEVIER SCIENCE BV. - 2211-2855. ; 27, s. 430-438
-
Tidskriftsartikel (refereegranskat)abstract
- A non-fullerene electron acceptor bearing a novel backbone with fused 10-heterocyclic ring (in-dacenodithiopheno-indacenodiselenophene), denoted by IDTIDSe-IC is developed for fullerene free polymer solar cells. IDTIDSe-IC exhibits a low band gap (E-g=1.52 eV) and strong absorption in the 600850 nm region. Combining with a large band gap polymer J51 (E-g=1.91 eV) as donor, broad absorption coverage from 300 nm to 800 nm is obtained due to complementary absorption of J51 and IDTIDSe-IC, which enables a high PCE of 8.02% with a V-oc of 0.91 V, a J(SC) of 15.16 mA/cm(2) and a FF of 58.0% in the corresponding PSCs. Moreover, the EQE of 50-65% is achieved in the absorption range of IDTIDSe-IC with only about 0.1 eV HOMO difference between J51 and IDTIDSe-IC. (C) 2016 Elsevier Ltd. All rights reserved.
|
|
| 3. |
- Zhang, Jianyun, et al.
(författare)
-
Revealing the Critical Role of the HOMO Alignment on Maximizing Current Extraction and Suppressing Energy Loss in Organic Solar Cells
- 2019
-
Ingår i: iScience. - : Cell Press. - 2589-0042. ; 19, s. 883-893
-
Tidskriftsartikel (refereegranskat)abstract
- For state-of-the-art organic solar cells (OSCs) consisting of a large-bandgap polymer donor and a near-infrared (NIR) molecular acceptor, the control of the HOMO offset is the key to simultaneously achieve small energy loss (Eloss) and high photocurrent. However, the relationship between HOMO offsets and the efficiency for hole separation is quite elusive so far, which requires a comprehensive understanding on how small the driving force can effectively perform the charge separation while obtaining a high photovoltage to ensure high OSC performance. By designing a new family of ZITI-X NIR acceptors (X = S, C, N) with a high structural similarity and matching them with polymer donor J71 forming reduced HOMO offsets, we systematically investigated and established the relationship among the photovoltaic performance, energy loss, and hole-transfer kinetics. We achieved the highest PCEavgs of 14.05 ± 0.21% in a ternary system (J71:ZITI-C:ZITI-N) that best optimize the balance between driving force and energy loss.
|
|
| 4. |
- Bi, Zhaozhao, et al.
(författare)
-
Individual nanostructure optimization in donor and acceptor phases to achieve efficient quaternary organic solar cells
- 2019
-
Ingår i: Nano Energy. - : ELSEVIER. - 2211-2855 .- 2211-3282. ; 66
-
Tidskriftsartikel (refereegranskat)abstract
- Fullerene derivative (PC71BM) and high crystallinity molecule (DR3TBDTT) are employed into PTB7-Th:FOIC based organic solar cells (OSCs) to cooperate an individual nanostructure optimized quaternary blend. PC71BM functions as molecular adjuster and phase modifier promoting FOIC forming "head-to-head" molecular packing and neutralizing the excessive FOIC crystallites. A multi-scale modified morphology is present thanks to the mixture of FOIC and PC71BM while DR3TBDTT disperses into PTB7-Th matrix to reinforce donors crystal-linity and enhance domain purity. Morphology characterization highlights the importance of individually optimizated nanostructures for donor and acceptor, which contributes to efficient hole and electron transport toward improved carrier mobilities and suppressed non-geminated recombination. Therefore, a power conversion efficiency of 13.51% is realized for a quaternary device which is 16% higher than the binary device (PTB7-Th:FOIC). This work demonstrates that utilizing quaternary strategy for simultaneous optimization of donor and acceptor phases is a feasible way to realize high efficient OSCs.
|
|
| 5. |
- Chen, Youchun, et al.
(författare)
-
Insights into the working mechanism of cathode interlayers in polymer solar cells via [(C8H17)(4)N](4)[SiW12O40]
- 2016
-
Ingår i: Journal of Materials Chemistry A. - : ROYAL SOC CHEMISTRY. - 2050-7488 .- 2050-7496. ; 4:48, s. 19189-19196
-
Tidskriftsartikel (refereegranskat)abstract
- A low-cost (amp;lt;$1 per g), high-yield (amp;gt;90%), alcohol soluble surfactant-encapsulated polyoxometalate complex [(C8H17)(4)N](4)[SiW12O40] has been synthesized and utilized as a cathode interlayer (CIL) in polymer solar cells (PSCs). A power conversion efficiency of 10.1% can be obtained for PSCs based on PTB7-Th (poly[[2,6-4,8-di(5-ethylhexylthienyl) benzo[1,2-b;3,3-b]-dithiophene][3-fluoro-2[(2-ethylhexyl) carbonyl] thieno [3,4-b]-thiophenediyl]]):PC71BM ([6,6]-phenyl C71-butyric acidmethyl ester) due to the incorporation of [(C8H17)(4)N](4)[SiW12O40]. Combined measurements of current density-voltage characteristics, transient photocurrent, charge carrier mobility and capacitance-voltage characteristics demonstrate that [(C8H17)(4)N](4)[SiW12O40] can effectively increase the built-in potential, charge carrier density and mobility and accelerate the charge carrier extraction in PSCs. Most importantly, the mechanism of using [(C8H17)(4)N](4)[SiW12O40] as the CIL is further brought to light by X-ray photoemission spectroscopy (XPS) and ultraviolet photoemission spectroscopy (UPS) of the metal/ [(C8H17)(4)N](4)[SiW12O40] interface. The findings suggest that [(C8H17)(4)N](4)[SiW12O40] not only decreased the work function of the metal cathodes but also was n-doped upon contact with the metals, which provide insights into the working mechanism of the CILs simultaneously improving the open circuit voltage, short circuit current and fill factor in the PSCs.
|
|
| 6. |
- Feng, Guitao, et al.
(författare)
-
“Double-Cable” Conjugated Polymers with Linear Backbone toward High Quantum Efficiencies in Single-Component Polymer Solar Cells
- 2017
-
Ingår i: Journal of the American Chemical Society. - : AMER CHEMICAL SOC. - 0002-7863 .- 1520-5126. ; 139:51, s. 18647-18656
-
Tidskriftsartikel (refereegranskat)abstract
- A series of "double-cable" conjugated polymers were developed for application in efficient single-component polymer solar cells, in which high quantum efficiencies could be achieved due to the optimized nanophase separation between donor and acceptor parts. The new double-cable polymers contain electron-donating poly(benzodithiophene) (BDT) as linear conjugated backbone for hole transport and pendant electron-deficient perylene bisimide (PBI) units for electron transport, connected via a dodecyl linker. Sulfur and fluorine substituents were introduced to tune the energy levels and crystallinity of the conjugated polymers. The double-cable polymers adopt a "face-on" orientation in which the conjugated BDT backbone and the pendant PBI units have a preferential pi-pi stacking direction perpendicular to the substrate, favorable for interchain charge transport normal to the plane. The linear conjugated backbone acts as a scaffold for the crystallization of the PBI groups, to provide a double-cable nanophase separation of donor and acceptor phases. The optimized nanophase separation enables efficient exciton dissociation as well as charge transport as evidenced from the high-up to 80%-internal quantum efficiency for photon-to-electron conversion. In single-component organic solar cells, the double-cable polymers provide power conversion efficiency up to 4.18%. This is one of the highest performances in single-component organic solar cells. The nanophase-separated design can likely be used to achieve high-performance single-component organic solar cells.
|
|
| 7. |
- Jin, Yingzhi, et al.
(författare)
-
Limitations and Perspectives on Triplet-Material-Based Organic Photovoltaic Devices
- 2019
-
Ingår i: Advanced Materials. - : WILEY-V C H VERLAG GMBH. - 0935-9648 .- 1521-4095. ; 31:22
-
Tidskriftsartikel (refereegranskat)abstract
- Organic photovoltaic cells (OPVs) have attracted broad attention and become a very energetic field after the emergence of nonfullerene acceptors. Long-lifetime triplet excitons are expected to be good candidates for efficiently harvesting a photocurrent. Parallel with the development of OPVs based on singlet materials (S-OPVs), the potential of triplet materials as photoactive layers has been explored. However, so far, OPVs employing triplet materials in a bulk heterojunction have not exhibited better performance than S-OPVs. Here, the recent progress of representative OPVs based on triplet materials (T-OPVs) is briefly summarized. Based on that, the performance limitations of T-OPVs are analyzed. The shortage of desired triplet materials with favorable optoelectronic properties for OPVs, the tradeoff between long lifetime and high binding energy of triplet excitons, as well as the low charge mobility in most triplet materials are crucial issues restraining the efficiencies of T-OPVs. To overcome these limitations, first, novel materials with desired optoelectronic properties are urgently demanded; second, systematic investigation on the contribution and dynamics of triplet excitons in T-OPVs is necessary; third, close multidisciplinary collaboration is required, as proved by the development of S-OPVs.
|
|
| 8. |
- Pan, W. W., et al.
(författare)
-
Optical properties and band bending of InGaAs/GaAsBi/InGaAs type-II quantum well grown by gas source molecular beam epitaxy
- 2016
-
Ingår i: Journal of Applied Physics. - : AIP Publishing. - 0021-8979 .- 1089-7550. ; 120:10
-
Tidskriftsartikel (refereegranskat)abstract
- Photoluminescence (PL) properties of In0.2Ga0.8As/GaAs0.96Bi0.04/In0.2Ga0.8As quantum well (QW) grown on GaAs substrates by gas source molecular beam epitaxy were studied by varying excitation power and temperature, respectively. The type-II transition energy shifts from 1.149 eV to 1.192 eV when increasing the excitation power from 10 mW to 150 mW at 4.5 K, which was ascribed to the band-bending effect. On the other hand, the type-II PL quenches quickly along with fast redshift with the increasing temperature due to the relaxation of the band bending caused by the thermal excitation process. An 8 band k.p model was used to analyze the electronic properties and the band-bending effect in the type-II QW. The calculated subband levels and transition energy fit well with the experiment results, and two thermal activation energies of 8.7 meV and 50 meV, respectively, are deduced. Published by AIP Publishing.
|
|
| 9. |
- Qian, Deping, et al.
(författare)
-
Design rules for minimizing voltage losses in high-efficiency organic solar cells
- 2018
-
Ingår i: Nature Materials. - : NATURE PUBLISHING GROUP. - 1476-1122 .- 1476-4660. ; 17:8, s. 703-
-
Tidskriftsartikel (refereegranskat)abstract
- The open-circuit voltage of organic solar cells is usually lower than the values achieved in inorganic or perovskite photovoltaic devices with comparable bandgaps. Energy losses during charge separation at the donor-acceptor interface and non-radiative recombination are among the main causes of such voltage losses. Here we combine spectroscopic and quantum-chemistry approaches to identify key rules for minimizing voltage losses: (1) a low energy offset between donor and acceptor molecular states and (2) high photoluminescence yield of the low-gap material in the blend. Following these rules, we present a range of existing and new donor-acceptor systems that combine efficient photocurrent generation with electroluminescence yield up to 0.03%, leading to non-radiative voltage losses as small as 0.21 V. This study provides a rationale to explain and further improve the performance of recently demonstrated high-open-circuit-voltage organic solar cells.
|
|
| 10. |
- Xu, Bo, et al.
(författare)
-
Integrated Design of Organic Hole Transport Materials for Efficient Solid-State Dye-Sensitized Solar Cells
- 2015
-
Ingår i: Advanced Energy Materials. - : Wiley. - 1614-6832 .- 1614-6840. ; 5:3
-
Tidskriftsartikel (refereegranskat)abstract
- A series of triphenylamine-based small molecule organic hole transport materials (HTMs) with low crystallinity and high hole mobility are systematically investigated in solid-state dye-sensitized solar cells (ssDSCs). By using the organic dye LEG4 as a photosensitizer, devices with X3 and X35 as the HTMs exhibit desirable power conversion efficiencies (PCEs) of 5.8% and 5.5%, respectively. These values are slightly higher than the PCE of 5.4% obtained by using the state-of-the-art HTM Spiro-OMeTAD. Meanwhile, transient photovoltage decay measurement is used to gain insight into the complex influences of the HTMs on the performance of devices. The results demonstrate that smaller HTMs induce faster electron recombination in the devices and suggest that the size of a HTM plays a crucial role in device performance, which is reported for the first time.
|
|
