| 1. |
- Corcoran, Angelica, 1988, et al.
(författare)
-
Comparing the structural development of sand and rock ilmenite during long-term exposure in a biomass fired 12 MWth CFB-boiler
- 2018
-
Ingår i: Fuel Processing Technology. - : Elsevier BV. - 0378-3820. ; 171, s. 39-44
-
Tidskriftsartikel (refereegranskat)abstract
- Oxygen Carrier Aided Combustion (OCAC) is a novel combustion concept with the purpose to increase the overall efficiency in conventional circulating fluidized bed (CFB) boilers. By replacing the commonly used bed material with an oxygen carrier (OC), the conceptual idea is to utilize the fluid dynamics in a CFB and the inherent oxygen transport supported by the OC to increase the oxygen distribution within the furnace in time and space. The OCAC concept has been successfully validated and further reached long-term demonstration in full scale operation (75-MW th ). This work presents a first evaluation of how ilmenite particles are affected in regard to mechanical resistance during long-term exposure to OCAC conditions in Chalmers 12-MW th CFB-boiler. A sand and a rock ilmenite are evaluated with regard to their mechanical stability. For evaluation, samples of the fresh materials and samples collected during operation in the Chalmers boiler are investigated. The study shows that the two materials differ in how the mechanical degradation occurs with exposure time. The sand ilmenite form cavities which are held together by an ash layer before they are shattered into numerous pieces, whereas the rock ilmenite develops distinct cracks that cause splitting of the particles.
|
|
| 2. |
- Maric, Jelena, 1983, et al.
(författare)
-
Valorization of Automobile Shredder Residue Using Indirect Gasification
- 2018
-
Ingår i: Energy & Fuels. - : American Chemical Society (ACS). - 1520-5029 .- 0887-0624. ; 32:12, s. 12795-12804
-
Tidskriftsartikel (refereegranskat)abstract
- Dual fluidized bed (DFB) gasification offers the possibility to convert solid fuels into a valuable gas, comprised of syngas, and hydrocarbons that can be readily handled in petrochemical units. DFB gasifiers are especially suitable for nonhomogeneous fuels, such as waste fractions. In this work, the possibility to use DFB gasification as a recycling/valorization method of automobile shredder residue is investigated. The gasification tests were carried out in the Chalmers 2–4 MWth gasifier over 4 days. The effects of ash on the gas and tar compositions, as well as on the activity of the bed inventory, were evaluated. The results show that 60% of the total carbon in the fuel can be recovered in the form of a permanent gas, whereby the produced gas contains 12%mol of C2–3 hydrocarbons. The tar levels measured in the produced gas were high, although it was clear that decomposition into monomer-like compounds occurred in the reactor, which resulted in the production of valuable petrochemical compounds, corresponding to 8–9% of the carbon in the feed. Using a higher operating temperature was found to be beneficial in terms of obtaining a higher gas yield, regardless of the level of ash enrichment in the system. The high ash levels in the fuel feed did not negatively affect the technical operation of the fluidized bed. Possible routes of carbon recovery are discussed.
|
|
| 3. |
- Palme, Anna, 1986, et al.
(författare)
-
Development of an efficient route for combined recycling of PET and cotton from mixed fabrics
- 2017
-
Ingår i: Textiles and Clothing Sustainability. - : Springer Science and Business Media LLC. - 2197-9936. ; 3:4
-
Tidskriftsartikel (refereegranskat)abstract
- Most textile waste is either incinerated or landfilled today, yet, the material could instead be recycled through chemical recycling to new high-quality textiles. A first important step is separation since chemical recycling of textiles requires pure streams. The focus of this paper is on the separation of cotton and PET (poly(ethylene terephthalate), polyester) from mixed textiles, so called polycotton. Polycotton is one of the most common materials in service textiles used in sheets and towels at hospitals and hotels. A straightforward process using 5–15 wt% NaOH in water and temperature in the range between 70 and 90 °C for the hydrolysis of PET was evaluated on the lab-scale. In the process, the PET was degraded to terephthalic acid (TPA) and ethylene glycol (EG). Three product streams were generated from the process. First is the cotton; second, the TPA; and, third, the filtrate containing EG and the process chemicals. The end products and the extent of PET degradation were characterized using light microscopy, UV-spectroscopy, and ATR FT-IR spectroscopy, as well as solution and solid-state NMR spectroscopy. Furthermore, the cotton cellulose degradation was evaluated by analyzing the intrinsic viscosity of the cotton cellulose. The findings show that with the addition of a phase transfer catalyst (benzyltributylammonium chloride (BTBAC)), PET hydrolysis in 10% NaOH solution at 90 °C can be completed within 40 min. Analysis of the degraded PET with NMR spectroscopy showed that no contaminants remained in the recovered TPA, and that the filtrate mainly contained EG and BTBAC (when added). The yield of the cotton cellulose was high, up to 97%, depending on how long the samples were treated. The findings also showed that the separation can be performed without the phase transfer catalyst; however, this requires longer treatment times, which results in more cellulose degradation.
|
|
| 4. |
|
|
| 5. |
- B. Erdal, Nejla, et al.
(författare)
-
Green Strategy to Reduced Nanographene Oxide through Microwave Assisted Transformation of Cellulose
- 2018
-
Ingår i: ACS Sustainable Chemistry and Engineering. - : American Chemical Society (ACS). - 2168-0485. ; 6:1, s. 1245-1255
-
Tidskriftsartikel (refereegranskat)abstract
- A green strategy for fabrication of biobased reduced nanographene oxide (r-nGO) was developed. Cellulose derived nanographene oxide (nGO) type carbon nanodots were reduced by microwave assisted hydrothermal treatment with superheated water alone or in the presence of caffeic acid (CA), a green reducing agent. The carbon nanodots, r-nGO and r-nGO-CA, obtained through the two different reaction routes without or with the added reducing agent, were characterized by multiple analytical techniques including FTIR, XPS, Raman, XRD, TGA, TEM, AFM, UV-vis, and DLS to confirm and evaluate the efficiency of the reduction reactions. A significant decrease in oxygen content accompanied by increased number of sp2 hybridized functional groups was confirmed in both cases. The synergistic effect of superheated water and reducing agent resulted in the highest C/O ratio and thermal stability, which also supported a more efficient reduction. Interesting optical properties were detected by fluorescence spectroscopy where nGO, r-nGO, and r-nGO-CA all displayed excitation dependent fluorescence behavior. r-nGO-CA and its precursor nGO were evaluated toward osteoblastic cells MG-63 and exhibited nontoxic behavior up to 200 μg mL-1, which gives promise for utilization in biomedical applications.
|
|
| 6. |
- Vera, C. M., et al.
(författare)
-
A preliminary study on the selectivity of linear polynuclear aromatic hydrocarbons in SFC using phenyl-type stationary phases
- 2015
-
Ingår i: Microchemical journal (Print). - : Elsevier. - 0026-265X .- 1095-9149. ; 121, s. 136-140
-
Tidskriftsartikel (refereegranskat)abstract
- The retention behaviour of a homologous series of polyaromatic hydrocarbons was evaluated on two phenyl-type stationary phases in reversed phase supercritical fluid chromatography (SFC). These phases were the Synergi polar-RP phase and the Cosmosil 5PBB phase, both of which are polar end-capped and incorporate an ether in a propyl chain that tethers the phenyl ring to the silica surface. The Cosmosil 5PBB phase also has five bromine atoms on the phenyl ring. The retention capacity of the Cosmosil column was substantially greater than the Synergi column. However, selectivity on the Cosmosil column was effectively independent of the acetonitrile modifier composition in the CO2 mobile phase, whereas, selectivity on the Synergi column was greatly affected by the acetonitrile modifier in the CO2 mobile phase. The results from this study showed that selectivity and retention studies in HPLC cannot be used to predict selectivity and retention behaviour in SFC. (C) 2015 Elsevier B.V. All rights reserved.
|
|
| 7. |
- Adamopoulos, Stergios, et al.
(författare)
-
Acoustic properties of acetylated wood under different humid conditions and its relevance for musical instruments
- 2018
-
Ingår i: Proceedings of the 9th European Conference on Wood Modification 2018, Arnhem, The Netherlands. - The Netherlands : Practicum. ; , s. 236-243
-
Konferensbidrag (refereegranskat)abstract
- In musical instrument making, less expensive wood species and materials with good characteristics and acoustical properties can provide potentials to find alternatives to the traditional exotic wood species used today. Modified wood could be such a choice if shows similar sound characteristics to wood coming from endangered and expensive tropical species with problematic commercial availability. In musical instruments, the overall functionality depends on the contribution of wood to different material performance indexes like sound radiation coefficient (R), characteristic impedance (z) and acoustic conversion efficiency (ACE). In this study, the performance indexes were measured for acetylated beech, maple and radiata pine and compared with these obtained for the reference wood materials maple, mahogany, alder and ash. A non-destructive free-free flexural vibration test method was used at constant temperature (20oC) but in different humid conditions- dry (35% RH), standard (65% RH) and wet (85% RH). Dimensional changes in the different humid conditions were also taken in account. Acetylated wood showed lower EMC with higher dimensional stability at each humidity level as compared with the reference wood materials. These properties are considered important factors for making quality musical instruments. Based on the acoustical properties, acetylated wood materials, especially radiata pine, showed good potential for use for musical instruments where specific characteristics of sound are required. However, the other types of acetylated wood can also be used for specific musical instruments.
|
|
| 8. |
- Al-Rudainy, Basel, et al.
(författare)
-
Impact of lignin content on the properties of hemicellulose hydrogels
- 2019
-
Ingår i: Polymers. - : MDPI AG. - 2073-4360. ; 11:1
-
Tidskriftsartikel (refereegranskat)abstract
- Hemicellulose is a promising renewable raw material for the production of hydrogels. This polysaccharide exists in large amounts in various waste streams, in which they are usually impure and heavily diluted. Several downstream processing methods can be combined to concentrate and purify the hemicellulose. However, such an approach can be costly; hence, the effect of impurities on the formation and properties of hydrogels must be determined. Lignin usually exists in these waste streams as a major impurity that is also difficult to separate. This compound can darken hydrogels and decrease their swellability and reactivity, as shown in many studies. Other properties and effects of lignin impurities are equally important for the end application of hydrogels and the overall process economy. In this work, we examined the feasibility of producing hydrogels from hemicelluloses that originated from sodium-based spent sulfite liquor. A combination of membrane filtration and anti-solvent precipitation was used to extract and purify various components. The influence of the purity of hemicellulose and the addition of lignosulfonates (emulated impurities in the downstream processing) to the crosslinking reaction mixture on the mechanical, thermal, and chemical properties of hydrogels was determined.
|
|
| 9. |
- Danish, Muhammad, et al.
(författare)
-
Effect of solution matrix and pH in Z-nZVI-catalyzed percarbonate system on the generation of reactive oxygen species and degradation of 1,1,1-trichloroethane
- 2017
-
Ingår i: Water Science and Technology. - London, UK : IWA PUBLISHING. - 1606-9749 .- 1607-0798. ; 17:6, s. 1568-1578
-
Tidskriftsartikel (refereegranskat)abstract
- This study primarily focuses on evaluating the effects of solution matrix and pH for the generation of reactive oxygen species (ROSs) in a Z-nZVI-catalyzed sodium percarbonate (SPC) system to degrade 1,1,1-trichloroethane (1,1,1-TCA) in the absence and presence of a reducing agent (RA), i.e. hydroxylamine. Degradation of 1,1,1-TCA was 49.5% and 95% in the absence and presence of RA. Probe tests confirmed the generation of major hydroxyl radicals (OH center dot) and minor superoxide species (O-2(-center dot)), and scavenger tests verified the key role of OH center dot and less of O-2(-center dot) radicals. Degradation of 1,1,1-TCA decreased significantly in the presence of Cl- and HCO3-, while NO3- and SO42- had negligible effects in the absence of RA. Addition of RA significantly enhanced 1,1,1-TCA degradation by generating more OH center dot and O-2(-center dot) radicals in the presence of anions. Degradation of 1,1,1-TCA increased in the acidic range (1-5), while an inhibitive trend from neutral to basic (7-9) was observed. In contrast, a significant increase in 1,1,1-TCA degradation was observed with the addition of RA at all pH values (1-9). In conclusion, the anions and pH significantly influenced the generation and intensity of ROSs and 1,1,1-TCA was effectively degraded in the Z-nZVI-catalyzed SPC system in the presence of RA.
|
|
| 10. |
- Feng, S. Z., et al.
(författare)
-
Siloxane-Terminated Side Chain Engineering of Acceptor Polymers Leading to Over 7% Power Conversion Efficiencies in All-Polymer Solar Cells
- 2017
-
Ingår i: ACS Macro Letters. - : American Chemical Society (ACS). - 2161-1653. ; 6:11, s. 1310-1314
-
Tidskriftsartikel (refereegranskat)abstract
- To investigate the influence of functional pendent groups on acceptor polymers and photovoltaic properties of all-polymer solar cells (all-PSCs), two novel acceptor polymers containing siloxane-terminated side chains are synthesized and characterized. Increasing the content of siloxane-terminated side chains can reduce pi-pi stacking distance and improve crystalline behavior, yet lead to poorer solubility of the acceptor polymers. By modulating the proper loadings of siloxane-terminated side chains on the acceptor polymers, the PBDB-T:PNDI-Si25 all-PSC attains a maximal power conversion efficiency (PCE) of 7.4% with an outstanding fill factor of 0.68. The results provide, new insights for developing high-performance all-PSCs through functional group engineering on the acceptor polymers, to achieve good solubility, polymer miscibility, and blend morphology.
|
|
