SwePub
Sök i SwePub databas

  Utökad sökning

Träfflista för sökning "hsv:(TEKNIK OCH TEKNOLOGIER) hsv:(Materialteknik) srt2:(2020-2024)"

Sökning: hsv:(TEKNIK OCH TEKNOLOGIER) hsv:(Materialteknik) > (2020-2024)

  • Resultat 1-10 av 5653
Sortera/gruppera träfflistan
   
NumreringReferensOmslagsbildHitta
1.
  • Mahade, Satyapal, 1987-, et al. (författare)
  • Incorporation of graphene nano platelets in suspension plasma sprayed alumina coatings for improved tribological properties
  • 2021
  • Ingår i: Applied Surface Science. - : Elsevier BV. - 0169-4332 .- 1873-5584. ; 570
  • Tidskriftsartikel (refereegranskat)abstract
    • Graphene possesses high fracture toughness and excellent lubrication properties, which can be exploited to enhance tribological performance of coating systems utilized to combat wear. In this work, suspension plasma spray (SPS) process was employed to deposit a composite, graphene nano-platelets (GNP) incorporated alumina coating. For comparison, monolithic alumina was also deposited utilizing identical spray conditions. The as-deposited coatings were characterized in detail for their microstructure, porosity content, hardness, fracture toughness and phase composition. Raman analysis of the as-deposited composite coating confirmed retention of GNP. The composite coating also showed good microstructural integrity, comparable porosity, higher fracture toughness and similar alumina phase composition as the monolithic alumina coating. The as-deposited coatings were subjected to dry sliding wear tests. The GNP incorporated composite coating showed lower CoF and lower specific wear rate than the pure alumina coating. Additionally, the counter surface also showed a lower wear rate in case of the composite coating. Post-wear analysis performed by SEM/EDS showed differences in the coating wear track and in the ball wear track of monolithic and composite coatings. Furthermore, Raman analysis in the wear track of composite coating confirmed the presence of GNP. The micro-indentation and wear test results indicate that the presence of GNP in the composite coating aided in improving fracture toughness, lowering CoF and specific wear rate compared to the monolithic coating. Results from this work demonstrated retention of GNP in an SPS processed coating, which can be further exploited to design superior wear-resistant coatings.
  •  
2.
  • Duan, Shanghong, 1992, et al. (författare)
  • Determination of transverse and shear moduli of single carbon fibres
  • 2020
  • Ingår i: Carbon. - : Elsevier BV. - 0008-6223 .- 1873-3891. ; 158C, s. 772-782
  • Tidskriftsartikel (refereegranskat)abstract
    • Carbon fibres are extensively used for their high specific mechanical properties. Exploiting their high axial stiffness and strength, they are employed to reinforce polymer matrix materials in advanced composites. However, carbon fibres are not isotropic. Data of the elastic properties in the other directions of the fibres are still largely unknown. Furthermore, standardised methods to characterise these properties are lacking. In the present work, we propose a methodology to determine the transverse and shear moduli of single carbon fibres. An experimental procedure is developed to fabricate high-quality, flat fibre cross-sections in both longitudinal and transverse directions using Focused Ion Beam, which gives full control of the specimen geometry. Indentation modulus on those surfaces are obtained using both Atomic Force Microscopy (AFM) and nanoindentation tests. Hysteresis was found to occur in the nanoindentation tests. The hysteresis response was due to nano-buckling and reversible shear deformation of the carbon crystals. For this reason, indentation tests using AFM is recommended. From the AFM indentation tests the transverse and shear moduli of three different carbon fibres (IMS65, T800 and M60J) are successfully determined.
  •  
3.
  • Johansen, Marcus, 1994, et al. (författare)
  • Mapping nitrogen heteroatoms in carbon fibres using atom probe tomography and photoelectron spectroscopy
  • 2021
  • Ingår i: Carbon. - : Elsevier BV. - 0008-6223. ; 179, s. 20-27
  • Tidskriftsartikel (refereegranskat)abstract
    • Carbon fibres show great potential as multifunctional negative electrode for novel structural battery composites – a rechargeable electrochemical cell with structural function. The electrochemical performance of carbon materials can be enhanced with nitrogen heteroatoms, which conveniently are inherent in polyacrylonitrile (PAN)-based carbon fibres. However, it is not fully understood how the electrochemical performance is governed by microstructure and composition of the carbon fibres, particularly the distribution and chemical states of nitrogen heteroatoms. Here we reveal the atom-by-atom three-dimensional spatial distribution and the chemical states of nitrogen in three PAN-carbon fibre types (M60J, T800 and IMS65), using atom probe tomography (APT) and synchrotron hard X-ray photoelectron spectroscopy (HAXPES), and correlate the results to electrochemical performance. The findings pave the way for future tailoring of carbon fibre microstructure for multifunctional applications.
  •  
4.
  • Johansen, Marcus, 1994 (författare)
  • Microstructure of Carbon Fibres for Multifunctional Composites: 3D Distribution and Configuration of Atoms
  • 2021
  • Licentiatavhandling (övrigt vetenskapligt/konstnärligt)abstract
    • Lightweight energy storage is a must for increased driving range of electric vehicles. “Mass-less” energy storage can be achieved by directly storing energy in structural components. In such multifunctional devices called structural composite batteries, carbon fibres carry mechanical load and simultaneously act as negative battery electrode by hosting lithium ions in its microstructure. Little is known of how the microstructure of carbon fibres is optimised for multifunctionality, and deeper understanding of the configuration and the distribution of atoms in carbon fibres is needed. Here synchrotron hard X-ray photoelectron spectroscopy and atom probe tomography are used to reveal the chemical states and three-dimensional distribution of atoms in commercial carbon fibres. This thesis presents the first ever guide for how to perform atom probe tomography on carbon fibres, and the first ever three-dimensional atomic reconstruction of a carbon fibre. The results show that the chemical states and distribution of nitrogen heteroatoms in carbon fibres affect the electrochemical performance of the fibres. Carbon fibres performed electrochemically better with higher amount of nitrogen with pyridinic and pyrrolic configurations. Additionally, the nitrogen concentration varies throughout the carbon fibre, which may suggest that the electrochemical properties also vary throughout the carbon fibre. The knowledge provided by this thesis can lead to future carbon fibre designs with enhanced electrochemical performance for multifunctional applications.
  •  
5.
  • Dimitrios, Nikas, et al. (författare)
  • Effect of annealing on microstructure in railway wheel steel
  • 2022
  • Ingår i: 42Nd Riso International Symposium On Materials Science. - : Institute of Physics Publishing (IOPP). ; 1249
  • Konferensbidrag (refereegranskat)abstract
    • Railway wheels are commonly made from medium carbon steels (similar to 0.55 wt.% C), heat treated to a near pearlitic microstructure with 5-10% pro-eutectoid ferrite. During the operation of freight trains, where block brakes are used, high thermal loads occur together with the high contact stresses, which combined can affect the mechanical properties of the material. In this study, the effects of annealing on local microstructure and mechanical properties in pearlitic railway wheel steel were investigated using electron microscopy and micro-hardness. It is found that after annealing at 650 degrees C, the room temperature hardness reduces about 25%, accompanied by significant spheroidization of cementite in the pearlitic colonies, though the size and the orientation gradients of the pearlitic colonies have not changed much. The relationship between the microstructural changes and the mechanical properties are discussed.
  •  
6.
  • Krakhmalev, Pavel, 1973-, et al. (författare)
  • Influence of heat treatment under hot isostatic pressing (HIP) on microstructure of intermetallic-reinforced tool steel manufactured by laser powder bed fusion
  • 2020
  • Ingår i: Materials Science & Engineering A: Structural Materials: Properties, Microstructure and Processing. - : Elsevier BV. - 0921-5093 .- 1873-4936. ; 772
  • Tidskriftsartikel (refereegranskat)abstract
    • Microstructure and properties of as-built laser powder bed fusion (LPBF) steels differ from the conventional ones, and they may contain some porosity and lack of fusion. Therefore, post-treatments, including hot isostatic pressing (HIP), are used to density the material, and tailor the properties of the final product. Usually, HIP is performed as an operation separate from heat treatment. In the present investigation a new approach was used, in which the whole cycle of the heat treatment was carried out in HIP under pressure, and the influence of HIP on microstructure of an advanced stainless maraging tool steel manufactured by LPBF was investigated. For a comparison, a conventional steel grade of the same chemical composition, after a heat treatment at the same temperature-time conditions, was also characterized. The microstructure of the steel was investigated by means of advanced microscopy and atom probe tomography. The influence of the manufacturing route, heat treatment and HIP on microstructure, austenitic phase fraction and size distribution of precipitates was investigated, and the role of high pressure in stabilization of austenite in the microstructure was discussed. It was concluded that since HIP influences phase transformations, a fundamental understanding of the influence of HIP on microstructure is nececcary, and development of new post processing regimes guaranteeing the best performance of the material is required.
  •  
7.
  • Xu, Jinghao, et al. (författare)
  • On the strengthening and embrittlement mechanisms of an additively manufactured Nickel-base superalloy
  • 2020
  • Ingår i: Materialia. - : Elsevier BV. - 2589-1529. ; 10
  • Tidskriftsartikel (refereegranskat)abstract
    • The γ′ phase strengthened Nickel-base superalloy is one of the most significant dual-phase alloy systems for high-temperature engineering applications. The tensile properties of laser powder-bed-fused IN738LC superalloy in the as-built state have been shown to have both good strength and ductility compared with its post-thermal treated state. A microstructural hierarchy composed of weak texture, sub-micron cellular structures and dislocation cellular walls was promoted in the as-built sample. After post-thermal treatment, the secondary phase γ′ precipitated with various size and fraction depending on heat treatment process. For room-temperature tensile tests, the dominated deformation mechanism is planar slip of dislocations in the as-built sample while dislocations bypassing the precipitates via Orowan looping in the γ′ strengthened samples. The extraordinary strengthening effect due to the dislocation substructure in the as-built sample provides an addition of 372 MPa in yield strength. The results of our calculation are in agreement with experimental yield strength for all the three different conditions investigated. Strikingly, the γ′ strengthened samples have higher work hardening rate than as-built sample but encounter premature failure. Experimental evidence shows that the embrittlement mechanism in the γ′ strengthened samples is caused by the high dislocation hardening of the grain interior region, which reduces the ability to accommodate further plastic strain and leads to premature intergranular cracking. On the basis of these results, the strengthening micromechanism and double-edge effect of strength and ductility of Nickel-base superalloy is discussed in detail.
  •  
8.
  • Hanning, Fabian, et al. (författare)
  • The Effect of Grain Size on theSusceptibility Towards Strain Age Crackingof Wrought Haynes® 282®
  • 2020
  • Ingår i: SPS 2020. - Amsterdam : IOS Press. - 9781643681467 - 9781643681474 ; 13, s. 407-416
  • Konferensbidrag (övrigt vetenskapligt/konstnärligt)abstract
    • The effect of grain size on the suceptibility towards strain age cracking (SAC) has been investigated for Haynes® 282® in the tempeature range of 750 to 950°C after isothermal exposure up to 1800s. Grain growth was induced by heattreating the material at 1150°C for 2h, resulting in a fourfold increase in grain size. Hardness was significanlty reduced after heat treatment as compared to millannealed material. Large grain size resulted in intergranular fracture over a widertemperature range than small grain size material. Ductility was lowest at 850°C, while lower values were observed to be correlated to increased grain size. The rapid formation of grain boundary carbide networks in Haynes® 282® is found to be notable to compensate for higher local stresses on grain boundaries due to incresedgrain size. 
  •  
9.
  • Qin, Xiao, 1993, et al. (författare)
  • Microstructure and texture evolutions in FeCrAl cladding tube during pilger processing
  • 2023
  • Ingår i: Journal of Materials Research and Technology. - 2238-7854. ; 25, s. 5506-5519
  • Tidskriftsartikel (refereegranskat)abstract
    • The microstructure of FeCrAl cladding tubes depends on the fabricating process history. In this study, the microstructural characteristics of wrought FeCrAl alloys during industrial pilger processing into thin-walled tubes were investigated. The hot extruded tube showed ∼100 μm equiaxed grains with weak α∗-fiber in {h11}<1/h12> texture, while pilger rolling process change the microstructure to fragmented and elongated grains along the rolling direction. The pilgered textures could be predicted with the VPSC model. The inter-pass annealing at 800–850 °C for 1 h results in recovery and recrystallization of the ferric matrix and restoration of ductility. The final finished tube shows fine recrystallized grains (∼11 μm) with dominant γ-fiber in three dimensions. Pilger rolling enhanced α-fiber while annealing reduced α-fiber and enhanced γ-fiber. Microstructural evolution in the Laves precipitates followed the sequence of faceted needle-like → spherical → faceted ellipsoidal. Thermomechanical processing resulted in cladding tubes with an area fraction of ∼5% and a number density of 5 × 10−11 m−2 in Laves precipitates, which is half that of the first-pilgered tube. Laves precipitates pin the grain boundaries to control the microstructure and prevent grain coarsening.
  •  
10.
  • Shoja, Siamak, 1980 (författare)
  • Microstructure and plastic deformation of textured CVD alumina coatings
  • 2020
  • Licentiatavhandling (övrigt vetenskapligt/konstnärligt)abstract
    • It is known that the wear performance of α-alumina coatings produced by chemical vapor deposition (CVD) is significantly influenced by the type and degree of texture. However, the main reasons behind this behavior are not fully understood. This thesis contains studies of two related topics for increasing the understanding of α-alumina coatings. The first topic concerns the microstructure and texture development of CVD α-Al2O3 coatings, and the second topic concerns calculations and analysis of the Schmid factors ( m ) for coatings with different textures. By combining different analysis methods (such as XRD, SEM, FIB/SEM, TKD, TEM, STEM, XEDS), and theoretical and experimental Schmid factor analysis by MATLAB and EBSD, the microstructure and plastic deformation of α-alumina coatings were investigated.     The microstructures of three different CVD α-Al2O3 layers deposited onto a Ti(C,N,O) bonding layer were studied. Grain boundary diffusion of heavy elements from the substrate to the bonding layer/α-Al2O3 interface was observed. This may be the cause of a disturbance in the early growth of α-Al2O3. Additionally, it was found that the number of interfacial pores at the bonding layer/α-Al2O3 interface increased by introducing the H2S gas. The H2S gas also promoted an earlier development of the (0001) texture. The orientation of the grains was developed to the desired texture both as a gradual change over several grains and as an abrupt transformation from one grain to another.   The probability of plastic deformation in different wear zones on the rake face of a cutting tool was investigated theoretically and experimentally by analyzing Schmid factors for textured α-Al2O3 coatings. Schmid factor diagrams were constructed using MATLAB/MTEX and used to extract frequency distributions for different slip systems and textures. The results were compared with lateral distribution maps of Schmid factors obtained from experimental coatings. It was observed that basal slip is most easily activated in the transition zone, followed by prismatic slip systems 1 and 2 in coatings with an (0001)-texture. The homogeneous plastic deformation behavior observed in this coating is also connected to mostly high Schmid factors in the  m -value distribution. The differences between the  m -value distributions for the three slip systems are not that pronounced in the (01-1​2) and (11-20) textures, and the distributions are relatively wide. The low wear rate and more homogeneous deformation of the coating with (0001) texture compared to the other coating textures may be the result of the high plasticity, offered by the easy activation of basal slip and prismatic 1 slip, and the low spread of Schmid factor values at the transition zone.   In conclusion, the results presented in this thesis form a knowledge platform that can be used to understand the microstructure and wear mechanisms of textured CVD α-alumina coatings.
  •  
Skapa referenser, mejla, bekava och länka
  • Resultat 1-10 av 5653
Typ av publikation
tidskriftsartikel (4174)
konferensbidrag (600)
doktorsavhandling (332)
licentiatavhandling (158)
forskningsöversikt (131)
bokkapitel (120)
visa fler...
rapport (87)
annan publikation (20)
bok (9)
samlingsverk (redaktörskap) (8)
konstnärligt arbete (7)
proceedings (redaktörskap) (7)
patent (5)
visa färre...
Typ av innehåll
refereegranskat (4777)
övrigt vetenskapligt/konstnärligt (846)
populärvet., debatt m.m. (22)
Författare/redaktör
Hryha, Eduard, 1980 (84)
Jarfors, Anders E.W. ... (71)
Andersson, Joel, 198 ... (68)
Joshi, Shrikant V., ... (62)
Nyborg, Lars, 1958 (59)
Vitos, Levente (56)
visa fler...
Jönsson, Pär (53)
Hedström, Peter, 195 ... (50)
Asp, Leif, 1966 (48)
Akhtar, Farid (46)
Tang, Luping, 1956 (45)
Berglund, Lars, 1956 ... (44)
Klement, Uta, 1962 (42)
Thuvander, Mattias, ... (41)
Wågberg, Lars, 1956- (41)
Kaplan, Alexander F. ... (39)
Das, Oisik (38)
Chelgani, Saeed Cheh ... (38)
Cwirzen, Andrzej (38)
Ringsberg, Jonas, 19 ... (35)
Ghassemali, Ehsan, 1 ... (34)
Karasev, Andrey (34)
Karlsson, Stefan, 19 ... (34)
Persson, Cecilia (33)
Liu, Johan, 1960 (32)
Varna, Janis (32)
Guo, Sheng, 1981 (32)
Park, Joo Hyun (32)
Diószegi, Attila, 19 ... (30)
Hörnqvist Colliander ... (30)
Kádár, Roland, 1982 (30)
Müller, Christian, 1 ... (29)
Pederson, Robert, 19 ... (29)
Björklund, Stefan, 1 ... (29)
Ghorbani, Yousef (28)
Bushlya, Volodymyr (28)
M’Saoubi, Rachid (28)
Persson, Nils-Kriste ... (28)
Engqvist, Håkan, 197 ... (28)
Joffe, Roberts (27)
Sandström, Rolf (27)
Zanella, Caterina (26)
Rosenkranz, Jan (25)
Hedenqvist, Mikael S ... (25)
Larsson, Henrik (25)
Odqvist, Joakim (25)
Nypelö, Tiina, 1982 (24)
Barsoum, Zuheir, 197 ... (24)
Krajnik, Peter, 1977 (24)
Lopez, Elena (24)
visa färre...
Lärosäte
Chalmers tekniska högskola (1554)
Kungliga Tekniska Högskolan (1355)
Luleå tekniska universitet (716)
RISE (414)
Uppsala universitet (394)
Linköpings universitet (358)
visa fler...
Lunds universitet (351)
Högskolan Väst (334)
Jönköping University (224)
Stockholms universitet (189)
Mittuniversitetet (136)
Högskolan i Borås (110)
Karlstads universitet (106)
Göteborgs universitet (91)
Malmö universitet (73)
Linnéuniversitetet (69)
Umeå universitet (64)
Sveriges Lantbruksuniversitet (50)
Högskolan Dalarna (36)
Örebro universitet (26)
Karolinska Institutet (26)
Högskolan i Skövde (21)
Högskolan i Halmstad (16)
Blekinge Tekniska Högskola (14)
Högskolan i Gävle (12)
IVL Svenska Miljöinstitutet (12)
VTI - Statens väg- och transportforskningsinstitut (11)
Mälardalens universitet (6)
Konstfack (4)
Södertörns högskola (2)
Högskolan Kristianstad (1)
Riksantikvarieämbetet (1)
Naturhistoriska riksmuseet (1)
visa färre...
Språk
Engelska (5583)
Svenska (57)
Norska (5)
Tyska (3)
Kinesiska (3)
Spanska (1)
visa fler...
Finska (1)
visa färre...
Forskningsämne (UKÄ/SCB)
Teknik (5651)
Naturvetenskap (1375)
Lantbruksvetenskap (69)
Medicin och hälsovetenskap (60)
Humaniora (47)
Samhällsvetenskap (33)

År

Kungliga biblioteket hanterar dina personuppgifter i enlighet med EU:s dataskyddsförordning (2018), GDPR. Läs mer om hur det funkar här.
Så här hanterar KB dina uppgifter vid användning av denna tjänst.

 
pil uppåt Stäng

Kopiera och spara länken för att återkomma till aktuell vy