| 1. |
- Mahade, Satyapal, 1987-, et al.
(författare)
-
Incorporation of graphene nano platelets in suspension plasma sprayed alumina coatings for improved tribological properties
- 2021
-
Ingår i: Applied Surface Science. - : Elsevier BV. - 0169-4332 .- 1873-5584. ; 570
-
Tidskriftsartikel (refereegranskat)abstract
- Graphene possesses high fracture toughness and excellent lubrication properties, which can be exploited to enhance tribological performance of coating systems utilized to combat wear. In this work, suspension plasma spray (SPS) process was employed to deposit a composite, graphene nano-platelets (GNP) incorporated alumina coating. For comparison, monolithic alumina was also deposited utilizing identical spray conditions. The as-deposited coatings were characterized in detail for their microstructure, porosity content, hardness, fracture toughness and phase composition. Raman analysis of the as-deposited composite coating confirmed retention of GNP. The composite coating also showed good microstructural integrity, comparable porosity, higher fracture toughness and similar alumina phase composition as the monolithic alumina coating. The as-deposited coatings were subjected to dry sliding wear tests. The GNP incorporated composite coating showed lower CoF and lower specific wear rate than the pure alumina coating. Additionally, the counter surface also showed a lower wear rate in case of the composite coating. Post-wear analysis performed by SEM/EDS showed differences in the coating wear track and in the ball wear track of monolithic and composite coatings. Furthermore, Raman analysis in the wear track of composite coating confirmed the presence of GNP. The micro-indentation and wear test results indicate that the presence of GNP in the composite coating aided in improving fracture toughness, lowering CoF and specific wear rate compared to the monolithic coating. Results from this work demonstrated retention of GNP in an SPS processed coating, which can be further exploited to design superior wear-resistant coatings.
|
|
| 2. |
- Lindberg, Siv M, et al.
(författare)
-
A product semantic study of the influence of the sense of touch on the evaluation of wood-based materials
- 2013
-
Ingår i: Materials & design. - : Elsevier BV. - 0264-1275 .- 1873-4197 .- 0261-3069. ; 52, s. 300-307
-
Tidskriftsartikel (refereegranskat)abstract
- Based on product semantics, this study investigated how the tactile attributes of wood and wood-based composites are perceived and interpreted semantically. The wood-based samples included ash, birch, elm, oak, pine, OSB (oriented strand board), two wood pulp-reinforced polylactide composites, Comp A and B and one wood-fiber reinforced polypropene composite, Comp C. The subjects rated the samples by the descriptive words natural, exclusive, eco-. friendly, rough, inexpensive, reliable, warm, modern, snug and solid. The most significant differences between the samples were found for roughness and for the descriptors, reliable, natural and solid. A principal component analysis yielded three attributes based on the tactile perceptions: reliable, old-. fashioned and smooth. The solid wood pieces were perceived as natural and oak was perceived as being exclusive. The composite materials presented a greater variation in terms of perceived attributes than the wood specimens.
|
|
| 3. |
- Åkerfeldt, Maria, 1982, et al.
(författare)
-
Textile piezoelectric sensors – melt spun bi-component poly(vinylidene fluoride) fibres with conductive cores and poly(3,4-ethylene dioxythiophene)-poly(styrene sulfonate) coating as the outer electrode
- 2014
-
Ingår i: Fashion and Textiles. - : Springer Science and Business Media LLC. - 2198-0802. ; 1:1
-
Tidskriftsartikel (refereegranskat)abstract
- The work presented here addresses the outer electroding of a fully textile piezoelectric strain sensor, consisting of bi-component fibre yarns of β-crystalline poly(vinylidene fluoride) (PVDF) sheath and conductive high density polyethylene (HDPE)/carbon black (CB) core as insertions in a woven textile, with conductive poly(3,4-ethylene dioxythiophene)-poly(styrene sulfonate) (PEDOT:PSS) coatings developed for textile applications. Two coatings, one with a polyurethane binder and one without, were compared for the application and evaluated as electrode material in piezoelectric testing, as well as tested for surface resistivity, tear strength, abrasion resistance and shear flexing. Both coatings served their function as the outer electrodes in the system and no difference in this regard was detected between them. Omission of the binder resulted in a surface resistivity one order of magnitude less, of 12.3 Ω/square, but the surface resistivity of these samples increased more upon abrasion than the samples coated with binder. The tear strength of the textile coated with binder decreased with one third compared to the uncoated substrate, whereas the tear strength of the coated textile without binder increased with the same amount. Surface resistivity measurements and scanning electron microscopy (SEM) images of the samples subjected to shear flexing showed that the coatings without the binder did not withstand this treatment, and that the samples with the binder managed this to a greater extent. In summary, both of the PEDOT:PSS coatings could be used as outer electrodes of the piezoelectric fibres, but inclusion of binder was found necessary for the durability of the coating.
|
|
| 4. |
- Grolig, Jan Gustav, 1986
(författare)
-
Coated Ferritic Stainless Steels as Interconnects in Solid Oxide Fuel Cells - Material Development and Electrical Properties
- 2015
-
Doktorsavhandling (övrigt vetenskapligt/konstnärligt)abstract
- Solid oxide fuel cells (SOFCs) are attracting increasing interest as devices with potentialuses in decentralized and clean electricity and heat production. Several challengeswith respect to materials have to be overcome to achieve efficiencies and life-spansthat are sufficient for long-term applications.An important element of an SOFC stack is the interconnect component, which connectstwo adjacent fuel cell elements. Interconnects, which are commonly composedof ferritic stainless steels, have to be corrosion-resistant, mechanically stable and costoptimized.This work aimed to investigate economic solutions for interconnect materials and tounderstand the underlying mechanisms of degradation and electrical conduction ofthese materials. Mainly two substrates, a commercially available steel (AISI 441) anda ferritic stainless steel that was optimized for an SOFC application (Sandvik SanergyHT) were combined with different barrier coatings and exposed to a cathode-sideatmosphere. A method was developed that allows for the electrical characterizationof promising material systems and model alloys, thereby facilitating a fundamentalunderstanding of the dominant electrical conduction processes linked to the oxidescales that grow on interconnects. The AISI 441 steel coated with reactive elementsand cobalt showed good corrosion and chromium evaporation profiles, while AISI 441coated with cerium and cobalt also had promising electrical properties. The SanergyHT steel was examined with coatings of copper and iron and copper and manganese,respectively. The corrosion and chromium evaporation profiles of Sanergy HT wereimproved by coating with copper and iron. The copper and iron-coated Sanergy HTshowed lower area specific resistance values than cobalt-coated Sanergy HT. Chromia,which is the main constituent of oxide scales, was synthesized using differentmethods. The electrical properties of chromia were found to be sensitive to not onlyimpurities, but also heat treatment. Finally the electrical properties of cobalt- andcobalt cerium-coated Sanergy HT steels were investigated. It was revealed that theaddition of cerium improved the conductivity of the interconnect by both slowingdown chromia growth and preventing the outward diffusion of iron into the spinel.
|
|
| 5. |
- Dimitrios, Nikas, et al.
(författare)
-
Effect of annealing on microstructure in railway wheel steel
- 2022
-
Ingår i: 42Nd Riso International Symposium On Materials Science. - : Institute of Physics Publishing (IOPP). ; 1249
-
Konferensbidrag (refereegranskat)abstract
- Railway wheels are commonly made from medium carbon steels (similar to 0.55 wt.% C), heat treated to a near pearlitic microstructure with 5-10% pro-eutectoid ferrite. During the operation of freight trains, where block brakes are used, high thermal loads occur together with the high contact stresses, which combined can affect the mechanical properties of the material. In this study, the effects of annealing on local microstructure and mechanical properties in pearlitic railway wheel steel were investigated using electron microscopy and micro-hardness. It is found that after annealing at 650 degrees C, the room temperature hardness reduces about 25%, accompanied by significant spheroidization of cementite in the pearlitic colonies, though the size and the orientation gradients of the pearlitic colonies have not changed much. The relationship between the microstructural changes and the mechanical properties are discussed.
|
|
| 6. |
- Goel, Sneha, 1993-, et al.
(författare)
-
Effect of post-treatments under hot isostatic pressure on microstructural characteristics of EBM-built Alloy 718
- 2019
-
Ingår i: Additive Manufacturing. - : Elsevier BV. - 2214-8604 .- 2214-7810. ; 28, s. 727-737
-
Tidskriftsartikel (refereegranskat)abstract
- Electron beam melting (EBM) has emerged as an important additive manufacturing technique. In this study, Alloy 718 produced by EBM was investigated in as-built and post-treated conditions for microstructural characteristics and hardness. The post-treatments investigated were hot isostatic pressing (HIP) and combined HIP + heat treatment (HIP + HT) carried out as a single cycle inside the HIP vessel. Both the post-treatments resulted in significant decrease in defects inevitably present in the as-built material. The columnar grain structure of the as-built material was found to be maintained after post-treatment, with some sporadic localized grain coarsening noted. Although HIP led to complete dissolution of δ and γ′′ phase, stable NbC and TiN (occasionally present) particles were observed in the post-treated specimens. Significant precipitation of γ′′ phase was observed after HIP + HT, which was attributed to the two-step aging heat treatment carried out during HIP + HT. The presence of γ′′ phase or otherwise was correlated to the hardness of the material. While the HIP treatment resulted in drop in hardness, HIP + HT led to ‘recovery’ of the hardness to values exceeding those exhibited by the as-built material.
|
|
| 7. |
- Goel, Sneha, 1993-, et al.
(författare)
-
The Effect of Location and Post-treatment on the Microstructure of EBM-Built Alloy 718
- 2018
-
Ingår i: Proceedings of the 9th International Symposium on Superalloy 718 & Derivatives. - Cham : Springer. - 2367-1696 .- 2367-1181. - 9783319894799 - 9783319894805 ; , s. 115-129
-
Konferensbidrag (refereegranskat)abstract
- Additive manufacturing (AM) of Ni-based superalloys such as Alloy 718 may obviate the need for difficult machining and welding operations associated with geometrically intricate parts, thus potentially expanding design possibilities and facilitating cost-effective manufacture of complex components. However, processing AM builds completely free from defects, which may impair mechanical properties such as fatigue and ductility, is challenging. Anisotropic properties, microstructural heterogeneities and local formation of undesired phases are additional concerns that have motivated post-treatment of AM builds. This work investigates the microstructural changes associated with post-treatment of Alloy 718 specimens produced by Electron Beam Melting (EBM) for as-built microstructures at 3 build heights: near base plate, in the middle of build and near the top of the build. Two different post-treatment conditions, hot isostatic pressing (HIP) alone and a combined HIP with solutionising and two-step aging were examined and compared to the results for the as-built condition. The influence of various post-treatments on minor phase distributions (δ, γ″, carbides), overall porosity, longitudinal grain widths and Vickers microhardness was considered. The HIP treatment led to significant reduction in overall porosity and dissolution of δ phase, which led to appreciable grain growth for both post-treatment conditions. The variation in hardness noted as a function of build height for the as-built specimens was eliminated after post-treatment. Overall, the hardness was found to decrease after HIP and increase after the full HIP, solutionising and aging treatment, which was attributed to dissolution of γ″ during HIP and its re-precipitation in subsequent heat treatment steps.
|
|
| 8. |
- Jaladurgam, Nitesh Raj, 1993
(författare)
-
Heterogeneous deformation of multi-phase engineering materials - an in-situ neutron diffraction study
- 2019
-
Licentiatavhandling (övrigt vetenskapligt/konstnärligt)abstract
- Gas turbines are complex power generation systems used in aerospace or land-based-power stations. Materials such as Ni-base superalloys are involved in the combustion zone of these machines, which continuously experiences harsh environments with loading at high temperatures. Moreover, the continuous demand for increasing operating temperature to achieve higher efficiencies and reduced emission levels opens the scene to new heat resistant materials like the state-of-the-art high entropy alloys (HEAs), which require a thorough understanding of the structure-process-property relationships. The microstructures of these advanced multi-phase, multi-component alloys are complex, and the deformation is generally heterogeneous both with respect to the different phases and to the crystallographic orientation within each phase. Hence, it is important to understand their behavior and performance during processing and service. In-situ neutron diffraction is a unique technique to probe the deformation behaviour during service/processing-like conditions, including plastic deformation at various temperatures, in order to provide insights into the structure-property relations. In the first part of this work the deformation mechanisms of a newly developed Ni-base superalloy was investigated using in-situ neutron diffraction and electron microscopy at room temperature. In addition, elasto-plastic self-consistent (EPSC) crystal plasticity simulations are used to obtain insights into the operating deformation mechanisms. In the second part, the as-cast eutectic high entropy alloy AlCoCrFeNi2.1 was studied using in-situ neutron diffraction at temperatures from 77 to 673 K. These investigations provide unique insights into the complex heterogeneous deformation behavior of these high-performance multi-phase engineering materials.
|
|
| 9. |
- Krakhmalev, Pavel, 1973-, et al.
(författare)
-
Influence of heat treatment under hot isostatic pressing (HIP) on microstructure of intermetallic-reinforced tool steel manufactured by laser powder bed fusion
- 2020
-
Ingår i: Materials Science & Engineering A: Structural Materials: Properties, Microstructure and Processing. - : Elsevier BV. - 0921-5093 .- 1873-4936. ; 772
-
Tidskriftsartikel (refereegranskat)abstract
- Microstructure and properties of as-built laser powder bed fusion (LPBF) steels differ from the conventional ones, and they may contain some porosity and lack of fusion. Therefore, post-treatments, including hot isostatic pressing (HIP), are used to density the material, and tailor the properties of the final product. Usually, HIP is performed as an operation separate from heat treatment. In the present investigation a new approach was used, in which the whole cycle of the heat treatment was carried out in HIP under pressure, and the influence of HIP on microstructure of an advanced stainless maraging tool steel manufactured by LPBF was investigated. For a comparison, a conventional steel grade of the same chemical composition, after a heat treatment at the same temperature-time conditions, was also characterized. The microstructure of the steel was investigated by means of advanced microscopy and atom probe tomography. The influence of the manufacturing route, heat treatment and HIP on microstructure, austenitic phase fraction and size distribution of precipitates was investigated, and the role of high pressure in stabilization of austenite in the microstructure was discussed. It was concluded that since HIP influences phase transformations, a fundamental understanding of the influence of HIP on microstructure is nececcary, and development of new post processing regimes guaranteeing the best performance of the material is required.
|
|
| 10. |
- Xu, Jinghao, et al.
(författare)
-
On the strengthening and embrittlement mechanisms of an additively manufactured Nickel-base superalloy
- 2020
-
Ingår i: Materialia. - : Elsevier BV. - 2589-1529. ; 10
-
Tidskriftsartikel (refereegranskat)abstract
- The γ′ phase strengthened Nickel-base superalloy is one of the most significant dual-phase alloy systems for high-temperature engineering applications. The tensile properties of laser powder-bed-fused IN738LC superalloy in the as-built state have been shown to have both good strength and ductility compared with its post-thermal treated state. A microstructural hierarchy composed of weak texture, sub-micron cellular structures and dislocation cellular walls was promoted in the as-built sample. After post-thermal treatment, the secondary phase γ′ precipitated with various size and fraction depending on heat treatment process. For room-temperature tensile tests, the dominated deformation mechanism is planar slip of dislocations in the as-built sample while dislocations bypassing the precipitates via Orowan looping in the γ′ strengthened samples. The extraordinary strengthening effect due to the dislocation substructure in the as-built sample provides an addition of 372 MPa in yield strength. The results of our calculation are in agreement with experimental yield strength for all the three different conditions investigated. Strikingly, the γ′ strengthened samples have higher work hardening rate than as-built sample but encounter premature failure. Experimental evidence shows that the embrittlement mechanism in the γ′ strengthened samples is caused by the high dislocation hardening of the grain interior region, which reduces the ability to accommodate further plastic strain and leads to premature intergranular cracking. On the basis of these results, the strengthening micromechanism and double-edge effect of strength and ductility of Nickel-base superalloy is discussed in detail.
|
|
