Sökning: id:"swepub:oai:DiVA.org:liu-154074" >
Thermomechanical fa...
Thermomechanical fatigue crack growth in a single crystal nickel base superalloy
-
- Palmert, Frans, 1986- (författare)
- Linköpings universitet,Konstruktionsmaterial,Tekniska fakulteten,Siemens industrial turbomachinery, Sweden
-
- Moverare, Johan, 1973- (författare)
- Linköpings universitet,Konstruktionsmaterial,Tekniska fakulteten
-
- Gustafsson, David, 1983- (författare)
- Siemens industrial turbomachinery, Sweden
-
(creator_code:org_t)
- Elsevier, 2019
- 2019
- Engelska.
-
Ingår i: International Journal of Fatigue. - : Elsevier. - 0142-1123 .- 1879-3452. ; 122, s. 184-198
- Relaterad länk:
-
https://liu.diva-por... (primary) (Raw object)
-
visa fler...
-
http://liu.diva-port...
-
https://urn.kb.se/re...
-
https://doi.org/10.1...
-
visa färre...
Abstract
Ämnesord
Stäng
- Thermomechanical fatigue crack growth in a single crystal nickel base superalloy was studied. Tests were performed on single edge notched specimens, using in phase and out of phase thermomechanical fatigue cycling with temperature ranges of 100-750°C and 100-850°C and hold times at maximum temperature ranging from 10s to 6h. Isothermal testing at 100°C, 750°C and 850°C was also performed using the same test setup. A compliance-based method is proposed to experimentally evaluate the crack opening stress and thereby estimate the effective stress intensity factor range ΔKeff for both isothermal and nonisothermal conditions. For in phase thermomechanical fatigue, the crack growth rate is increased if a hold time is applied at the maximum temperature. By using the compliance-based crack opening evaluation, this increase in crack growth rate was explained by an increase in the effective stress intensity factor range which accelerated the cycle dependent crack growth. No significant difference in crack growth rate vs ΔKeff was observed between in phase thermomechanical fatigue tests and isothermal tests at the maximum temperature. For out of phase thermomechanical fatigue, the crack growth rate was insensitive to the maximum temperature and also to the length of hold time at maximum temperature. The crack growth rate vs ΔKeff during out of phase thermomechanical fatigue was significantly higher than during isothermal fatigue at the minimum temperature, even though the advancement of the crack presumably occurs at the same temperature. Dissolution of γ′ precipitates and recrystallization at the crack tip during out of phase thermomechanical fatigue is suggested as a likely explanation for this difference in crack growth rate.
Ämnesord
- TEKNIK OCH TEKNOLOGIER -- Materialteknik (hsv//swe)
- ENGINEERING AND TECHNOLOGY -- Materials Engineering (hsv//eng)
- TEKNIK OCH TEKNOLOGIER -- Maskinteknik -- Teknisk mekanik (hsv//swe)
- ENGINEERING AND TECHNOLOGY -- Mechanical Engineering -- Applied Mechanics (hsv//eng)
- TEKNIK OCH TEKNOLOGIER -- Materialteknik -- Bearbetnings-, yt- och fogningsteknik (hsv//swe)
- ENGINEERING AND TECHNOLOGY -- Materials Engineering -- Manufacturing, Surface and Joining Technology (hsv//eng)
- TEKNIK OCH TEKNOLOGIER -- Materialteknik -- Metallurgi och metalliska material (hsv//swe)
- ENGINEERING AND TECHNOLOGY -- Materials Engineering -- Metallurgy and Metallic Materials (hsv//eng)
- TEKNIK OCH TEKNOLOGIER -- Samhällsbyggnadsteknik -- Infrastrukturteknik (hsv//swe)
- ENGINEERING AND TECHNOLOGY -- Civil Engineering -- Infrastructure Engineering (hsv//eng)
Nyckelord
- single crystal superalloy
- thermomechanical fatigue
- crack growth
- crack closure
Publikations- och innehållstyp
- ref (ämneskategori)
- art (ämneskategori)
Hitta via bibliotek
Till lärosätets databas