| 1. |
- Enmark, Markus, 1991, et al.
(författare)
-
A Critical Assessment of Nano Enhanced Vapor Chamber Wick Structures for Electronics Cooling
- 2021
-
Ingår i: 2021 23rd European Microelectronics and Packaging Conference and Exhibition, EMPC 2021.
-
Konferensbidrag (refereegranskat)abstract
- The increasing need for high thermal dissipation in small electronic products puts tough requirements on effective cooling solutions. Two of the most effective passive cooling devices in electronics today are vapor chambers and heat pipes. With new advancements in materials science and nanotechnology comes the possibility to further increase cooling capacity and at the same time make devices lighter. This study is a critical assessment on recent progress in the field of nanomaterial enhanced wick structures in vapor chambers and heat pipes. In this paper, nano-enhanced wick structures are divided into five different sub-categories based on material type. Publication trends for the different types of nano-enhanced wicks are studied by plotting them on a timeline. It is found that nanostructured metal wicks is the most studied field in recent years. A plot showing wick performance in terms of superheat temperatures for given heat flux is created to be used for benchmarking of new wick structures when pool boil experiments are carried out. An attempt to find correlation between publication trends, type of wick and performance is done. On the basis of the gathered data it is deemed difficult to find a distinct correlation, this is mainly due to difficulty in comparing performance between different studies, especially when different heat fluxes are used. There is no unambiguous answer to which category of nano-enhanced wicks that should be target for future studies. Graphene coating and pure carbon nanomaterials such as aerogels and graphene foam are still relatively unexplored and believed to have great potential if they can be attached to envelope materials.
|
|
| 2. |
- Enmark, Markus, 1991, et al.
(författare)
-
Reliability Characterization of Graphene Enhanced Thermal Interface Material for Electronics Cooling Applications
- 2022
-
Ingår i: 2022 IMAPS Nordic Conference on Microelectronics Packaging, NordPac 2022.
-
Konferensbidrag (refereegranskat)abstract
- Graphene-based products are gaining popularity in thermal management applications in high performance electronics systems. The ultra-high thermal conductivity of graphene together with its relatively low density makes it a suitable material for reaching high cooling capability in lightweight applications. An example of products that are starting to enter the market is graphene enhanced thermal interface materials (TIMs). Pristine graphene enhanced TIMs are well characterized and show high thermal conductivity and low thermal interface resistance. Before these TIMs can take the next step from being a niche product to reach high volume sales on the market, it needs to be proven that they have stable performance over time when conditioned and aged according to industry reliability standards. In this work, a set of customized test rigs was designed, and graphene enhanced TIMs of three different thicknesses were tested. The TIMs were compressed by 30% and then subjected to three different industry standard reliability tests; thermal aging, temperature cycling and damp heat. The thermal resistance was measured sequentially during each test to monitor change over time. The reliability tests are still ongoing and so far the tested graphene enhanced TIMs have stable performance over time with some observable trends for the different tests. At the current test time the maximum degradation in thermal resistance is 13%, measured after 511 cycles in the thermal cycling test. The used test method is deemed promising for reliability comparison and future requirement standardization on thermal pads.
|
|
| 3. |
- Fazi, Andrea, 1992, et al.
(författare)
-
Multiple growth of graphene from a pre-dissolved carbon source
- 2020
-
Ingår i: Nanotechnology. - : IOP Publishing. - 1361-6528 .- 0957-4484. ; 31:34, s. 345601-
-
Tidskriftsartikel (refereegranskat)abstract
- Mono- to few-layer graphene materials are successfully synthesized multiple times using Cu-Ni alloy as a catalyst after a single-chemical vapor deposition (CVD) process. The multiple synthesis is realized by extracting carbon source pre-dissolved in the catalyst substrate. Firstly, graphene is grown by the CVD method on Cu-Ni catalyst substrates. Secondly, the same Cu-Nicatalyst foils are annealed, in absence of any external carbon precursor, to grow graphene using the carbon atoms pre-dissolved in the catalyst during the CVD process. This annealing process is repeated to synthesize graphene successfully until carbon is exhausted in the Cu-Ni foils. After the CVD growth and each annealing growth process, the as-grown graphene is removed using a bubbling transfer method. A wide range of characterizations are performed to examine the quality of the obtained graphene material and to monitor the carbon concentration in the catalyst substrates. Results show that graphene from each annealing growth process possesses a similar quality, which confirmed the good reproducibility of the method. This technique brings great freedom to graphene growth and applications, and it could be also used for other 2D material synthesis.
|
|
| 4. |
- Fu, Yifeng, 1984, et al.
(författare)
-
Graphene related materials for thermal management
- 2020
-
Ingår i: 2D Materials. - : IOP Publishing. - 2053-1583. ; 7:1
-
Tidskriftsartikel (refereegranskat)abstract
- Almost 15 years have gone ever since the discovery of graphene as a single atom layer. Numerous papers have been published to demonstrate its high electron mobility, excellent thermal and mechanical as well as optical properties. We have recently seen more and more applications towards using graphene in commercial products. This paper is an attempt to review and summarize the current status of the research of the thermal properties of graphene and other 2D based materials including the manufacturing and characterization techniques and their applications, especially in electronics and power modules. It is obvious from the review that graphene has penetrated the market and gets more and more applications in commercial electronics thermal management context. In the paper, we also made a critical analysis of how mature the manufacturing processes are; what are the accuracies and challenges with the various characterization techniques and what are the remaining questions and issues left before we see further more applications in this exciting and fascinating field.
|
|
| 5. |
- Guo, Sihua, et al.
(författare)
-
Toward ultrahigh thermal conductivity graphene films
- 2023
-
Ingår i: 2D Materials. - : IOP Publishing. - 2053-1583. ; 10:1
-
Tidskriftsartikel (refereegranskat)abstract
- With increasing demands of high-performance and functionality, electronics devices generate a great amount of heat. Thus, efficient heat dissipation is crucially needed. Owing to its extremely good thermal conductivity, graphene is an interesting candidate for this purpose. In this paper, a two-step temperature-annealing process to fabricate ultrahigh thermal conductive graphene assembled films (GFs) is proposed. The thermal conductivity of the obtained GFs was as high as 3826 +/- 47 W m(-1) K-1. Extending the time of high-temperature annealing significantly improved the thermal performance of the GF. Structural analyses confirmed that the high thermal conductivity is caused by the large grain size, defect-free stacking, and high flatness, which are beneficial for phonon transmission in the carbon lattice. The turbostratic stacking degree decreased with increasing heat treatment time. However, the increase in the grain size after long heat treatment had a more pronounced effect on the phonon transfer of the GF than that of turbostratic stacking. The developed GFs show great potential for efficient thermal management in electronics devices.
|
|
| 6. |
- Hansson, Josef, 1991, et al.
(författare)
-
Effects of high temperature treatment of carbon nanotube arrays on graphite : Increased crystallinity, anchoring and inter-tube bonding
- 2020
-
Ingår i: Nanotechnology. - : Institute of Physics Publishing (IOPP). - 0957-4484 .- 1361-6528. ; 31:45
-
Tidskriftsartikel (refereegranskat)abstract
- Thermal treatment of carbon nanotubes (CNTs) can significantly improve their mechanical, electrical and thermal properties due to reduced defects and increased crystallinity. In this work we investigate the effect of annealing at 3000 degrees C of vertically aligned CNT arrays synthesized by chemical vapor deposition (CVD) on graphite. Raman measurements show a drastically reduced amount of defects and, together with transmission electron microscope (TEM) diffraction measurements, an increased average crystallite size of around 50%, which corresponds to a 124% increase in Young's modulus. We also find a tendency for CNTs to bond to each other with van der Waals (vdW) forces, which causes individual CNTs to closely align with each other. This bonding causes a densification effect on the entire CNT array, which appears at temperatures >1000 degrees C. The densification onset temperature corresponds to the thermal decomposition of oxygen containing functional groups, which otherwise prevents close enough contact for vdW bonding. Finally, the remaining CVD catalyst on the bottom of the CNT array is evaporated during annealing, enabling direct anchoring of the CNTs to the underlying graphite substrate.
|
|
| 7. |
- Liu, Ya, 1991, et al.
(författare)
-
Graphene based thermal management system for battery cooling in electric vehicles
- 2020
-
Ingår i: Proceedings - 2020 IEEE 8th Electronics System-Integration Technology Conference, ESTC 2020.
-
Konferensbidrag (refereegranskat)abstract
- In this work, a graphene assembled film integrated heat sink and water cooling technology was used to build an experimental set-up of a thermal management system to demonstrate the possibility to achieve efficient cooling of the propulsion battery in electric vehicles. The experimental results showed that the temperature decrease of a Li-ion battery module can reach 11°C and 9 °C under discharge rates as of 2C and 1C, respectively. The calculated thermal resistance of the graphene based cooling system is about 76% of a similar copper based cooling system. Surface modification was carried out on the graphene sheet to achieve a reliable bonding between the graphene sheet and the battery cell surface. This work provides a proof of concept of a new highly efficient approach for electric vehicle battery thermal management using the light-weight material graphene.
|
|
| 8. |
- Nylander, Andreas, 1988, et al.
(författare)
-
Degradation of Carbon Nanotube Array Thermal Interface Materials through Thermal Aging: Effects of Bonding, Array Height, and Catalyst Oxidation
- 2021
-
Ingår i: ACS Applied Materials & Interfaces. - : American Chemical Society (ACS). - 1944-8252 .- 1944-8244. ; 13:26, s. 30992-31000
-
Tidskriftsartikel (refereegranskat)abstract
- Carbon nanotube (CNT) array thermal interface materials (TIMs) are promising candidates for high-performance applications in terms of thermal performance. However, in order to be useful in commercial applications, the reliability of the interfaces is an equally important parameter, which so far has not been thoroughly investigated. In this study, the reliability of CNT array TIMs is investigated through accelerated aging. The roles of CNT array height and substrate configuration are studied for their relative impact on thermal resistance degradation. After aging, the CNT catalyst is analyzed using X-ray photoelectron spectroscopy to evaluate chemical changes. The CNT-catalyst bond appears to degrade during aging but not to the extent that the TIM performance is compromised. On the other hand, coefficient of thermal expansion mismatch between surfaces creates strain that needs to be absorbed, which requires CNT arrays with sufficient height. Transfer and bonding of both CNT roots and tips also create more reliable interfaces. Crucially, we find that the CNT array height of most previously reported CNT array TIMs is not enough to prevent significant reliability problems.
|
|
| 9. |
- Sun, Peng, et al.
(författare)
-
Scalable three-dimensional Ni 3 P-based composite networks for flexible asymmertric supercapacitors
- 2020
-
Ingår i: Chemical Engineering Journal. - : Elsevier BV. - 1385-8947. ; 380
-
Tidskriftsartikel (refereegranskat)abstract
- Flexible energy storage devices are of great importance in future wearable electronics. To achieve the popularization of these flexible equipments, it is urgent to develop proper productive method for easily scaling up high performance flexible electrode materials. Herein, a three-dimensional nano-network composite material based on Ni3P is designed on flexible carbon felt (CF). The network induced by the introduction of sulfonated polystyrene combines advantages of excellent redox ability of the Ni3P, great conductivity of NiCo alloy and fast electric double layer contribution of carbon. It shows a great energy storage performance and an excellent balance between areal and gravimetric capacitance (1.76 F cm−2 and 1048 F g−1), which are beneficial to the actual application. Besides, this CF@NiCoNiPC can be easily produced in a large-scale due to the simple and low-cost synthetic method. The CF@NiCoNiPC can be further fabricated into an asymmetric supercapacitor (ASC), which demonstrates an excellent capacitance of 516.7 mF cm−2 (170.5 F g−1) and long-term stability of 25,000 charging and discharging cycles (83% retentions). Excitingly, the ASC presents good mechanical performance with 92% capacitance retention after 1000 bending cycles. Three tandem ASCs can easily power a red LED for several minutes when charged for only 20 s even under a bent state, indicating the great potential in future flexible energy storage devices.
|
|
| 10. |
- Zehri, Abdelhafid, 1989, et al.
(författare)
-
Exploring Graphene Coated Copper Nanoparticles as a multifunctional Nanofiller for Micro-Scaled Copper Paste
- 2021
-
Ingår i: 2021 23rd European Microelectronics and Packaging Conference and Exhibition, EMPC 2021.
-
Konferensbidrag (refereegranskat)abstract
- The current development of the electronics system requires capabilities beyond conventional heat transfer approaches. New solutions based on advanced materials are being developed to tackle the current challenges in the development of electronics systems and the nanoscale 2D materials such as graphene are at the centre of the effort to exploit the intrinsic properties of carbon nanomaterials. In this work, we introduce a new concept of graphene-coated copper nanoparticles (G-CuNPs) and explore their multifunctional potential applications in metallic based paste used in electronics. The nanoscale powder was found to present a core/shell structure with the copper particle at its core and a disordered multilayer graphene structure continuously coating its surface. The composition of the particles was analysed, and the presence of the coating was found to provide oxidation protection for the metallic core. Thermogravimetric analysis (TGA) showed an additional role of the G-CuNPs with a reduction effect without the use of an additional reducing agent. Furthermore, due to the combined effect of the size of the particles and the oxidation-free metallic core, Differential Scanning Calorimetry (DSC) analysis revealed a melting depression at temperatures as low as 155 °C. Finally, the mechanical properties of the nanocoating were investigated and the results showed an enhanced ductility at the surface of the particles due to the presence of the multi-layered graphene structure, which might be exploited for powder flow and lubrication effect.
|
|
| 11. |
- Zehri, Abdelhafid, 1989, et al.
(författare)
-
Graphene Oxide and Nitrogen-Doped Graphene Coated Copper Nanoparticles in Water-Based Nanofluids for Thermal Management in Electronics
- 2022
-
Ingår i: JOURNAL OF NANOFLUIDS. - : American Scientific Publishers. - 2169-432X .- 2169-4338. ; 11:1, s. 125-134
-
Tidskriftsartikel (refereegranskat)abstract
- Graphene oxide (GO) and nitrogen-doped graphene (NG) coated copper nanoparticles (NPs) have been developed in this work and investigated as nanofiller for water as Heat Transfer Fluids (HTFs). The morphology and composition of the coating were characterized to confirm the presence of functional groups and the nitrogen-doping of the graphene coating. Different fractions of the two types of coated nanoparticles NPs between 0.1 and 10 wt.% were dispersed in water. The thermal conductivity of the dispersions was evaluated at temperatures between 20 and 50 degrees C. A positive correlation between the thermal conductivity of the HTFs and the fraction and temperature are observed as a result of the increase of the solid phase contribution into the heat transfer. At a concentration of 0.5 wt.%, the thermal conductivity of the NG-CuNPs nanofluid reached its maximum increase of 78%, compared to a 13% increase in the case of GO-CuNPs. However, due to the poor stability of the NG-CuNPs, further increase of the solid phase did not result in any additional improvement. In contrast, the thermal conductivity of the GO-based dispersion resulted in a 103% enhancement at 10 wt.% at a temperature of 50 degrees C.
|
|
| 12. |
- Zehri, Abdelhafid, 1989, et al.
(författare)
-
High porosity and light weight graphene foam heat sink and phase change material container for thermal management
- 2020
-
Ingår i: Nanotechnology. - : IOP Publishing. - 1361-6528 .- 0957-4484. ; 31:42
-
Tidskriftsartikel (refereegranskat)abstract
- During the last decade, graphene foam emerged as a promising high porosity 3-dimensional (3D) structure for various applications. More specifically, it has attracted significant interest as a solution for thermal management in electronics. In this study, we investigate the possibility to use such porous materials as a heat sink and a container for a phase change material (PCM). Graphene foam (GF) was produced using chemical vapor deposition (CVD) process and attached to a thermal test chip using sintered silver nanoparticles (Ag NPs). The thermal conductivity of the graphene foam reached 1.3 W m(-1)K(-1), while the addition of Ag as a graphene foam silver composite (GF/Ag) enhanced further its effective thermal conductivity by 54%. Comparatively to nickel foam, GF and GF/Ag showed lower junction temperatures thanks to higher effective thermal conductivity and a better contact. A finite element model was developed to simulate the fluid flow through the foam structure model and showed a positive and a non-negligible contributions of the secondary microchannel within the graphene foam. A ratio of 15 times was found between the convective heat flux within the primary and secondary microchannel. Our paper successfully demonstrates the possibility of using such 3D porous material as a PCM container and heat sink and highlight the advantage of using the carbon-based high porosity material to take advantage of its additional secondary porosity.
|
|
| 13. |
- Zhao, Changhong, 1982, et al.
(författare)
-
Synthesis of graphene quantum dots and their applications in drug delivery
- 2020
-
Ingår i: Journal of Nanobiotechnology. - : Springer Science and Business Media LLC. - 1477-3155. ; 18:1
-
Forskningsöversikt (refereegranskat)abstract
- This review focuses on the recent advances in the synthesis of graphene quantum dots (GQDs) and their applications in drug delivery. To give a brief understanding about the preparation of GQDs, recent advances in methods of GQDs synthesis are first presented. Afterwards, various drug delivery-release modes of GQDs-based drug delivery systems such as EPR-pH delivery-release mode, ligand-pH delivery-release mode, EPR-Photothermal delivery-Release mode, and Core/Shell-photothermal/magnetic thermal delivery-release mode are reviewed. Finally, the current challenges and the prospective application of GQDs in drug delivery are discussed.[Figure not available: see fulltext.]
|
|
