| 1. |
- Abel, I, et al.
(författare)
-
Overview of the JET results with the ITER-like wall
- 2013
-
Ingår i: Nuclear Fusion. - : IOP Publishing. - 1741-4326 .- 0029-5515. ; 53:10, s. 104002-
-
Tidskriftsartikel (refereegranskat)abstract
- Following the completion in May 2011 of the shutdown for the installation of the beryllium wall and the tungsten divertor, the first set of JET campaigns have addressed the investigation of the retention properties and the development of operational scenarios with the new plasma-facing materials. The large reduction in the carbon content (more than a factor ten) led to a much lower Z(eff) (1.2-1.4) during L- and H-mode plasmas, and radiation during the burn-through phase of the plasma initiation with the consequence that breakdown failures are almost absent. Gas balance experiments have shown that the fuel retention rate with the new wall is substantially reduced with respect to the C wall. The re-establishment of the baseline H-mode and hybrid scenarios compatible with the new wall has required an optimization of the control of metallic impurity sources and heat loads. Stable type-I ELMy H-mode regimes with H-98,H-y2 close to 1 and beta(N) similar to 1.6 have been achieved using gas injection. ELM frequency is a key factor for the control of the metallic impurity accumulation. Pedestal temperatures tend to be lower with the new wall, leading to reduced confinement, but nitrogen seeding restores high pedestal temperatures and confinement. Compared with the carbon wall, major disruptions with the new wall show a lower radiated power and a slower current quench. The higher heat loads on Be wall plasma-facing components due to lower radiation made the routine use of massive gas injection for disruption mitigation essential.
|
|
| 2. |
- Romanelli, F, et al.
(författare)
-
Overview of the JET results
- 2011
-
Ingår i: Nuclear Fusion. - : IOP Publishing. - 1741-4326 .- 0029-5515. ; 51:9
-
Tidskriftsartikel (refereegranskat)abstract
- Since the last IAEA Conference JET has been in operation for one year with a programmatic focus on the qualification of ITER operating scenarios, the consolidation of ITER design choices and preparation for plasma operation with the ITER-like wall presently being installed in JET. Good progress has been achieved, including stationary ELMy H-mode operation at 4.5 MA. The high confinement hybrid scenario has been extended to high triangularity, lower ρ*and to pulse lengths comparable to the resistive time. The steady-state scenario has also been extended to lower ρ*and ν*and optimized to simultaneously achieve, under stationary conditions, ITER-like values of all other relevant normalized parameters. A dedicated helium campaign has allowed key aspects of plasma control and H-mode operation for the ITER non-activated phase to be evaluated. Effective sawtooth control by fast ions has been demonstrated with3He minority ICRH, a scenario with negligible minority current drive. Edge localized mode (ELM) control studies using external n = 1 and n = 2 perturbation fields have found a resonance effect in ELM frequency for specific q95values. Complete ELM suppression has, however, not been observed, even with an edge Chirikov parameter larger than 1. Pellet ELM pacing has been demonstrated and the minimum pellet size needed to trigger an ELM has been estimated. For both natural and mitigated ELMs a broadening of the divertor ELM-wetted area with increasing ELM size has been found. In disruption studies with massive gas injection up to 50% of the thermal energy could be radiated before, and 20% during, the thermal quench. Halo currents could be reduced by 60% and, using argon/deuterium and neon/deuterium gas mixtures, runaway electron generation could be avoided. Most objectives of the ITER-like ICRH antenna have been demonstrated; matching with closely packed straps, ELM resilience, scattering matrix arc detection and operation at high power density (6.2 MW m-2) and antenna strap voltages (42 kV). Coupling measurements are in very good agreement with TOPICA modelling. © 2011 IAEA, Vienna.
|
|
| 3. |
- Tran, K. B., et al.
(författare)
-
The global burden of cancer attributable to risk factors, 2010-19: a systematic analysis for the Global Burden of Disease Study 2019
- 2022
-
Ingår i: Lancet. - 0140-6736. ; 400:10352, s. 563-591
-
Tidskriftsartikel (refereegranskat)abstract
- Background Understanding the magnitude of cancer burden attributable to potentially modifiable risk factors is crucial for development of effective prevention and mitigation strategies. We analysed results from the Global Burden of Diseases, Injuries, and Risk Factors Study (GBD) 2019 to inform cancer control planning efforts globally. Methods The GBD 2019 comparative risk assessment framework was used to estimate cancer burden attributable to behavioural, environmental and occupational, and metabolic risk factors. A total of 82 risk-outcome pairs were included on the basis of the World Cancer Research Fund criteria. Estimated cancer deaths and disability-adjusted life-years (DALYs) in 2019 and change in these measures between 2010 and 2019 are presented. Findings Globally, in 2019, the risk factors included in this analysis accounted for 4.45 million (95% uncertainty interval 4.01-4.94) deaths and 105 million (95.0-116) DALYs for both sexes combined, representing 44.4% (41.3-48.4) of all cancer deaths and 42.0% (39.1-45.6) of all DALYs. There were 2.88 million (2.60-3.18) risk-attributable cancer deaths in males (50.6% [47.8-54.1] of all male cancer deaths) and 1.58 million (1.36-1.84) risk-attributable cancer deaths in females (36.3% [32.5-41.3] of all female cancer deaths). The leading risk factors at the most detailed level globally for risk-attributable cancer deaths and DALYs in 2019 for both sexes combined were smoking, followed by alcohol use and high BMI. Risk-attributable cancer burden varied by world region and Socio-demographic Index (SDI), with smoking, unsafe sex, and alcohol use being the three leading risk factors for risk-attributable cancer DALYs in low SDI locations in 2019, whereas DALYs in high SDI locations mirrored the top three global risk factor rankings. From 2010 to 2019, global risk-attributable cancer deaths increased by 20.4% (12.6-28.4) and DALYs by 16.8% (8.8-25.0), with the greatest percentage increase in metabolic risks (34.7% [27.9-42.8] and 33.3% [25.8-42.0]). Interpretation The leading risk factors contributing to global cancer burden in 2019 were behavioural, whereas metabolic risk factors saw the largest increases between 2010 and 2019. Reducing exposure to these modifiable risk factors would decrease cancer mortality and DALY rates worldwide, and policies should be tailored appropriately to local cancer risk factor burden. Copyright (C) 2022 The Author(s). Published by Elsevier Ltd. This is an Open Access article under the CC BY 4.0 license.
|
|
| 4. |
- Bécoulet, A., et al.
(författare)
-
Science and technology research and development in support to ITER and the Broader Approach at CEA
- 2013
-
Ingår i: Nuclear Fusion. - : IOP Publishing. - 1741-4326 .- 0029-5515. ; 53:10
-
Tidskriftsartikel (refereegranskat)abstract
- In parallel to the direct contribution to the procurement phase of ITER and Broader Approach, CEA has initiated research & development programmes, accompanied by experiments together with a significant modelling effort, aimed at ensuring robust operation, plasma performance, as well as mitigating the risks of the procurement phase. This overview reports the latest progress in both fusion science and technology including many areas, namely the mitigation of superconducting magnet quenches, disruption-generated runaway electrons, edge-localized modes (ELMs), the development of imaging surveillance, and heating and current drive systems for steady-state operation. The WEST (W Environment for Steady-state Tokamaks) project, turning Tore Supra into an actively cooled W-divertor platform open to the ITER partners and industries, is presented.
|
|
| 5. |
- Bryazka, D., et al.
(författare)
-
Population-level risks of alcohol consumption by amount, geography, age, sex, and year: a systematic analysis for the Global Burden of Disease Study 2020
- 2022
-
Ingår i: Lancet. - 0140-6736. ; 400:10347, s. 185-235
-
Tidskriftsartikel (refereegranskat)abstract
- Background The health risks associated with moderate alcohol consumption continue to be debated. Small amounts of alcohol might lower the risk of some health outcomes but increase the risk of others, suggesting that the overall risk depends, in part, on background disease rates, which vary by region, age, sex, and year. Methods For this analysis, we constructed burden-weighted dose-response relative risk curves across 22 health outcomes to estimate the theoretical minimum risk exposure level (TMREL) and non-drinker equivalence (NDE), the consumption level at which the health risk is equivalent to that of a non-drinker, using disease rates from the Global Burden of Diseases, Injuries, and Risk Factors Study (GBD) 2020 for 21 regions, including 204 countries and territories, by 5-year age group, sex, and year for individuals aged 15-95 years and older from 1990 to 2020. Based on the NDE, we quantified the population consuming harmful amounts of alcohol. Findings The burden-weighted relative risk curves for alcohol use varied by region and age. Among individuals aged 15-39 years in 2020, the TMREL varied between 0 (95% uncertainty interval 0-0) and 0.603 (0.400-1.00) standard drinks per day, and the NDE varied between 0.002 (0-0) and 1.75 (0.698-4.30) standard drinks per day. Among individuals aged 40 years and older, the burden-weighted relative risk curve was J-shaped for all regions, with a 2020 TMREL that ranged from 0.114 (0-0.403) to 1.87 (0.500-3.30) standard drinks per day and an NDE that ranged between 0.193 (0-0.900) and 6.94 (3.40-8.30) standard drinks per day. Among individuals consuming harmful amounts of alcohol in 2020, 59.1% (54.3-65.4) were aged 15-39 years and 76.9% (7.0-81.3) were male. Interpretation There is strong evidence to support recommendations on alcohol consumption varying by age and location. Stronger interventions, particularly those tailored towards younger individuals, are needed to reduce the substantial global health loss attributable to alcohol. Copyright (C) 2022 The Author(s). Published by Elsevier Ltd.
|
|
| 6. |
|
|
| 7. |
|
|
| 8. |
|
|
| 9. |
|
|
| 10. |
- Giroud, C., et al.
(författare)
-
Integration of a radiative divertor for heat load control into JET high triangularity ELMy H-mode plasmas
- 2012
-
Ingår i: Nuclear Fusion. - : IOP Publishing. - 0029-5515 .- 1741-4326. ; 52:6, s. 063022-
-
Tidskriftsartikel (refereegranskat)abstract
- Experiments on JET with a carbon-fibre composite wall have explored the reduction of steady-state power load in an ELMy H-mode scenario at high Greenwald fraction similar to 0.8, constant power and close to the L to H transition. This paper reports a systematic study of power load reduction due to the effect of fuelling in combination with seeding over a wide range of pedestal density ((4-8) x 10(19) m(-3)) with detailed documentation of divertor, pedestal and main plasma conditions, as well as a comparative study of two extrinsic impurity nitrogen and neon. It also reports the impact of steady-state power load reduction on the overall plasma behaviour, as well as possible control parameters to increase fuel purity. Conditions from attached to fully detached divertor were obtained during this study. These experiments provide reference plasmas for comparison with a future JET Be first wall and an all W divertor where the power load reduction is mandatory for operation.
|
|
| 11. |
- Giroud, C., et al.
(författare)
-
Progress at JET in integrating ITER-relevant core and edge plasmas within the constraints of an ITER-like wall
- 2015
-
Ingår i: Plasma Physics and Controlled Fusion. - : IOP Publishing. - 0741-3335 .- 1361-6587. ; 57:3
-
Tidskriftsartikel (refereegranskat)abstract
- This paper reports the progress made at JET-ILW on integrating the requirements of the reference ITER baseline scenario with normalized confinement factor of 1, at a normalized pressure of 1.8 together with partially detached divertor whilst maintaining these conditions over many energy confinement times. The 2.5 MA high triangularity ELMy H-modes are studied with two different divertor configurations with D-gas injection and nitrogen seeding. The power load reduction with N seeding is reported. The relationship between an increase in energy confinement and pedestal pressure with triangularity is investigated. The operational space of both plasma configurations is studied together with the ELM energy losses and stability of the pedestal of unseeded and seeded plasmas. The achievement of stationary plasma conditions over many energy confinement times is also reported.
|
|
| 12. |
- Maddison, G. P., et al.
(författare)
-
Contrasting H-mode behaviour with deuterium fuelling and nitrogen seeding in the all-carbon and metallic versions of JET
- 2014
-
Ingår i: Nuclear Fusion. - : IOP Publishing. - 0029-5515 .- 1741-4326. ; 54:7, s. 073016-
-
Tidskriftsartikel (refereegranskat)abstract
- The former all-carbon wall on JET has been replaced with beryllium in the main torus and tungsten in the divertor to mimic the surface materials envisaged for ITER. Comparisons are presented between type I H-mode characteristics in each design by examining respective scans over deuterium fuelling and impurity seeding, required to ameliorate exhaust loads both in JET at full capability and in ITER. Attention is focused upon a common high-triangularity, single-null divertor configuration at 2.5 MA, q(95) approximate to 3.5 yielding the most robust all-C performance. Contrasting results between the alternative linings are found firstly in unseeded plasmas, for which purity is improved and intrinsic radiation reduced in the ITER-like wall (ILW) but normalized energy confinement is approximate to 30% lower than in all-C counterparts, owing to a commensurately lower (electron) pedestal temperature. Divertor recycling is also radically altered, with slower, inboard-outboard asymmetric transients at ELMs and spontaneous oscillations in between them. Secondly, nitrogen seeding elicits opposite responses in the ILW to all-C experience, tending to raise plasma density, reduce ELM frequency, and above all to recover (electron) pedestal pressure, hence global confinement, almost back to previous levels. A hitherto unrecognized role of light impurities in pedestal stability and dynamics is consequently suggested. Thirdly, while heat loads on the divertor outboard target between ELMs are successfully reduced in proportion to the radiative cooling and ELM frequency effects of N in both wall environments, more surprisingly, average power ejected by ELMs also declines in the same proportion for the ILW. Detachment between transients is simultaneously promoted. Finally, inter-ELM W sources in the ILW divertor tend to fall with N input, although core accumulation possibly due to increased particle confinement still leads to significantly less steady conditions than in all-C plasmas. This limitation of ILW H-modes so far will be readdressed in future campaigns to continue progress towards a fully integrated scenario suitable for D-T experiments on JET and for 'baseline' operation on ITER. The diverse changes in behaviour between all-C and ILW contexts demonstrate essentially the strong impact which boundary conditions and intrinsic impurities can have on tokamak-plasma states.
|
|
| 13. |
- Monier-Garbet, P, et al.
(författare)
-
Impurity-seeded ELMy H-modes in JET, with high density and reduced heat load
- 2005
-
Ingår i: Nuclear Fusion. - : IOP Publishing. - 0029-5515 .- 1741-4326. ; 45:11, s. 1404-1410
-
Tidskriftsartikel (refereegranskat)abstract
- Experiments performed at JET during the past two years show that, in high triangularity H-mode plasmas with I-p = 2.5 MA, n(e)/n(Gr) approximate to 1.0, it is possible to radiate separately up to approximate to 40% of the total injected power on closed flux surfaces in the pedestal region (argon seeding) and up to approximate to 50% of the injected power in the divertor region (nitrogen seeding), while maintaining the confinement improvement factor at the value required for ITER, H98(y, 2) 1.0. The total radiated power fraction achieved in both cases (65-70%) is close to that required for ITER. However, Type I ELMS observed with impurity seeding have the same characteristics as that observed in reference pulses without seeding: decreasing plasma energy loss per ELM with increasing pedestal collisionality. One has to reach the Type III ELM regime to decrease the transient heat load to the divertor to acceptable values for ITER, although at the expense of confinement. The feasibility of an integrated scenario with Type-III ELMS, and q(95) = 2.6 to compensate for the low H factor, has been demonstrated on JET. This scenario would meet ITER requirements at 17 MA provided that the IPB98 scaling for energy content is accurate enough, and provided that a lower dilution is obtained when operating at higher absolute electron density.
|
|
| 14. |
- Stork, D., et al.
(författare)
-
Overview of transport, fast particle and heating and current drive physics using tritium in JET plasmas
- 2005
-
Ingår i: Nuclear Fusion. - 0029-5515 .- 1741-4326. ; 45:10, s. S181-S194
-
Tidskriftsartikel (refereegranskat)abstract
- Results are presented from the JET Trace Tritium Experimental (TTE) campaign using minority tritium (T) plasmas (n(T)/n(D) < 3%). Thermal tritium particle transport coefficients (D-T, nu(T)) are found to exceed neo-classical values in all regimes, except in ELMy H-modes at high densities and in the region of internal transport barriers (ITBs) in reversed shear plasmas. In ELMy H-mode dimensionless parameter scans, at q(95) 2.8 and triangularity delta = 0.2, the T particle transport scales in a gyro-Bohm manner in the inner plasma (r/a < 0.4), whilst the outer plasma particle transport scaling is more Bohm-like. Dimensionless parameter scans show contrasting behaviour for the trace particle confinement (increases with collisionality, nu* and beta) and bulk energy confinement (decreases with nu* and is independent of beta). In an extended ELMy H-mode data set, with rho*, nu*, and q varied but with neo-classical tearing modes (NTMs) either absent or limited to weak, benign core modes (4/3 or above), the multiparameter fit to the normalized diffusion coefficient in the outer plasma (0.65 < r/a < 0.8) gives D-T/B-phi similar to rho*(2.46) nu*(-0.23) beta(-1.01) q(2.03). In hybrid scenarios (q(min) similar to 1, low positive shear, no sawteeth), the T particle confinement is found to scale with increasing triangularity and plasma current. Comparing regimes (ELMy H-mode, ITB plasma and hybrid scenarios) in the outer plasma region, a correlation of high values of D-T with high values Of nu(T) is seen. The normalized diffusion coefficients for the hybrid and ITB scenarios do not fit the scaling derived for ELMy H-modes. The normalized tritium diffusion scales with normalized poloidal Larmor radius (rho(theta)* = q rho*) in a manner close to gyro-Bohm (similar to rho(sigma)*(3)), with an added inverse P dependence. The effects of ELMs, sawteeth and NTMs on the T particle transport are described. Fast-ion confinement in current-hole (CH) plasmas was tested in TTE by tritium neutral beam injection into JET CH plasmas. gamma-rays from the reactions of fusion alpha and beryllium impurities (Be-9(alpha, n gamma)C-12) characterized the fast fusion-alpha population evolution. The gamma-decay times are consistent with classical alpha plus parent fast triton slowing down times (tau(Ts) + tau(alpha s)) for high plasma currents (I-p > 2 MA) and monotonic q-profiles. In CH discharges the gamma-ray emission decay times are much lower than classical (tau(Ts) + tau(alpha s)), indicating alpha confinement degradation, due to the orbit losses and particle orbit drift predicted by a 3-D Fokker-Planck numerical code and modelled using TRANSP.
|
|
| 15. |
- Giroud, C., et al.
(författare)
-
Impact of nitrogen seeding on confinement and power load control of a high-triangularity JET ELMy H-mode plasma with a metal wall
- 2013
-
Ingår i: Nuclear Fusion. - : IOP Publishing. - 0029-5515 .- 1741-4326. ; 53:11, s. 113025-
-
Tidskriftsartikel (refereegranskat)abstract
- This paper reports the impact on confinement and power load of the high-shape 2.5MA ELMy H-mode scenario at JET of a change from all carbon plasma-facing components to an all metal wall. In preparation to this change, systematic studies of power load reduction and impact on confinement as a result of fuelling in combination with nitrogen seeding were carried out in JET-C and are compared with their counterpart in JET with a metallic wall. An unexpected and significant change is reported on the decrease in the pedestal confinement but is partially recovered with the injection of nitrogen.
|
|
| 16. |
- Santala, M. I. K., et al.
(författare)
-
Proton-triton nuclear reaction in ICRF heated plasmas in JET
- 2006
-
Ingår i: Plasma Physics and Controlled Fusion. - : IOP Publishing. - 0741-3335 .- 1361-6587. ; 48:8, s. 1233-1253
-
Tidskriftsartikel (refereegranskat)abstract
- Fast protons can react with tritons in an endothermic nuclear reaction which can act as a source of neutrons in magnetically confined fusion plasmas. We have performed an experiment to systematically study this reaction in low tritium concentration (approximate to 1%) plasmas in the Joint European Torus. A linear dependence is found between excess neutron rate and tritium concentration when the DT fusion rate is low. We discuss the properties of the neutron emission, including anisotropy, from the proton-triton reaction in a fusion reactor environment and derive simple models for the calculation of the neutron yield from this reaction in terms of tritium density, fast ion temperature and fast ion energy content.
|
|
| 17. |
- Voitsekhovitch, I., et al.
(författare)
-
Integrated modelling for tokamak plasma: Physics and scenario optimisation
- 2012
-
Ingår i: 39th EPS Conference on Plasma Physics 2012, EPS 2012 and the 16th International Congress on Plasma Physics; Stockholm; Sweden; 2 July 2012 through 6 July 2012; Code 96757. - 9781622769810 ; 2, s. 1314-1317
-
Konferensbidrag (refereegranskat)abstract
- Simulations of JET and AUG HS with the GLF23 model show that the observed core confinement improvement can be partly explained by the beneficial s/q effect on the ITG driven transport while the effect of the ExB shear stabilisation is weaker than in H-mode plasmas. Strong stabilising effect of βe on the ITG turbulence has been found, but the transport reduction due to this effect can be limited by the onset of the KBM mode at high βe. The simulations of toroidal rotation in HS with the GLF23 model give an indication of the toroidal momentum pinch (Pr
|
|
| 18. |
- Zastrow, K. D., et al.
(författare)
-
Tritium transport experiments on the JET tokamak
- 2004
-
Ingår i: Plasma Physics and Controlled Fusion. - 0741-3335 .- 1361-6587. ; 46, s. B255-B265
-
Tidskriftsartikel (refereegranskat)abstract
- An overview is given of the experimental method, the analysis technique and the results for trace tritium experiments conducted on the JET tokamak in 2003. Observations associated with events such as sawtooth collapses, neo-classical tearing modes and edge localized modes are described. Tritium transport is seen to approach neo-classical levels in the plasma core at high density and low q(95), and in the transport barrier region of internal transport barrier (ITB) discharges. Tritium transport remains well above neo-classical levels in all other cases. The correlation of the measured tritium diffusion coefficient and convection velocity for normalized minor radii r/a = [0.65, 0.80] with the controllable parameters q95 and plasma density are found to be consistent for all operational regimes (ELMy H-mode discharges with or without ion cyclotron frequency resonance heating, hybrid scenario and ITB discharges). Scaling with local physics parameters is best described by gyro-Bohm scaling with an additional inverse beta dependence.
|
|
| 19. |
- Airila, M. I., et al.
(författare)
-
Preliminary Monte Carlo simulation of beryllium migration during JET ITER-like wall divertor operation
- 2015
-
Ingår i: Journal of Nuclear Materials. - : Elsevier BV. - 0022-3115 .- 1873-4820. ; 463, s. 800-804
-
Tidskriftsartikel (refereegranskat)abstract
- Migration of beryllium into the divertor and deposition on tungsten in the final phase of the first ITER-like-wall campaign of JET are modelled with the 3D Monte Carlo impurity transport code ERO. The simulation covers the inner wall and the inner divertor. To generate the plasma background for Monte Carlo tracing of impurity particles, we use the EDGE2D/EIRENE code set. At the relevant regions of the wall, the estimated plasma conditions vary around T-e approximate to 5eV and n(e) 2 x 10(17) m(-3) (far-scrape-off layer; more than 10 cm away from the LCFS). We calculate impurity distributions in the plasma using the main chamber source as a free parameter in modelling and attempt to reproduce inter-ELM spectroscopic BeII line (527 nm) profiles at the divertor. The present model reproduces the level of emission close to the inner wall, but further work is needed to match also the measured emission peak values and ultimately link the modelled poloidal net deposition profiles of beryllium to post mortem data.
|
|
| 20. |
|
|
| 21. |
|
|
| 22. |
- Garzotti, L., et al.
(författare)
-
Simulations of density profiles in JET hybrid discharges
- 2012
-
Ingår i: 39th EPS Conference on Plasma Physics 2012, EPS 2012 and the 16th International Congress on Plasma Physics; Stockholm; Sweden; 2 July 2012 through 6 July 2012; Code 96757. - 9781622769810 ; 1, s. 157-160
-
Konferensbidrag (refereegranskat)
|
|
| 23. |
- Hillairet, J., et al.
(författare)
-
Recent progress on lower hybrid current drive and implications for ITER
- 2013
-
Ingår i: Nuclear Fusion. - : IOP Publishing. - 1741-4326 .- 0029-5515. ; 53:7
-
Tidskriftsartikel (refereegranskat)abstract
- The sustainment of steady-state plasmas in tokamaks requires efficient current drive systems. Lower hybrid current drive is currently the most efficient method to generate a continuous additional off-axis toroidal plasma current and to reduce the poloidal flux consumption during the plasma current ramp-up phase. The operation of the Tore Supra ITER-like lower hybrid (LH) launcher has demonstrated the capability to couple LH power at ITER-like power densities with very low reflected power during long pulses. In addition, the installation of eight 700 kW/CW klystrons at the LH transmitter has allowed increasing the total LH power in long-pulse scenarios. However, in order to achieve pure stationary LH-sustained plasmas, some R&D is needed to increase the reliability of all the systems and codes, from radio-frequency (RF) sources to plasma scenario prediction. The CEA/IRFM is addressing some of these issues by leading a R&D programme towards an ITER LH system and by the validation of an integrated LH modelling suite of codes. In 2011, the RF design of a mode converter was validated at a low power. A 500 kW/5 s RF window is currently under manufacture and will be tested at a high power in 2012 in collaboration with the National Fusion Research Institute. All of this work aims to reduce the operational risks associated with the ITER steady-state operations.
|
|
| 24. |
- Koskela, T., et al.
(författare)
-
Effect of tungsten off-axis accumulation on neutral beam deposition in JET rotating plasmas
- 2015
-
Ingår i: Plasma Physics and Controlled Fusion. - : IOP Publishing. - 0741-3335 .- 1361-6587. ; 57:4
-
Tidskriftsartikel (refereegranskat)abstract
- Evidence for low field side accumulation of tungsten is often observed in bolometry and soft x-ray emissivities of highly rotating JET ITER-like wall (ILW) plasmas. Poloidal variation of the density of high-Z impurities, such as tungsten, in the core of NBI heated plasmas is expected from neoclassical theory due to charge displacement and parallel electric field generated by the centrifugal force. We calculate the poloidally asymmetric distribution of tungsten using fluid equations and a 1D transport simulation with the JETTO/SANCO code. Peaking of tungsten on the outboard side of the plasma is found and verified with soft x-ray and bolometry measurements. We then study the effect of a poloidally asymmetric tungsten distribution on the distribution of the NBI heat source by simulations with the Monte Carlo code ASCOT. The simulations show that the poloidally asymmetric tungsten profile redistributes the fast NBI ions radially through shifting their ionization profile and poloidally through enhanced pitch-angle scattering at high energy. The amplitude of the redistribution is in the order of 10% for the highest n(W)/n(e) ratios of similar to 10(-4) measured in recent JET H-mode plasmas. As a result of the scattering of the beam particles, the core heat deposition is changed less than 10%, which does not have a significant impact to the performance of JET plasmas. The modelling is in qualitative agreement with measurements by the vertical neutron camera that sees a broadening in the 2.5 MeV neutron profile when tungsten peaks on the outboard side of the plasma.
|
|
| 25. |
- Lawson, K. D., et al.
(författare)
-
Improved EDGE2D-EIRENE simulations of JET ITER-like wall L-mode discharges utilising poloidal VUV/visible spectral emission profiles
- 2015
-
Ingår i: Journal of Nuclear Materials. - : Elsevier BV. - 0022-3115 .- 1873-4820. ; 463, s. 582-585
-
Tidskriftsartikel (refereegranskat)abstract
- A discrepancy in the divertor radiated powers between EDGE2D-EIRENE simulations, both with and without drifts, and JET-ILW experiments employing a set of NBI-heated L-mode discharges with step-wise density variation is investigated. Results from a VUV/visible poloidally scanning spectrometer are used together with bolometric measurements to determine the radiated power and its composition. The analysis shows the importance of D line radiation in contributing to the divertor radiated power, while contributions from D radiative recombination are smaller than expected. Simulations with W divertor plates underestimate the Be content in the divertor, since no allowance is made for Be previously deposited on the plates being re-eroded. An improved version of EDGE2D-EIRENE is used to test the importance of the deposited layer in which the sputtering yield from supposed pure Be divertor plates is reduced to match the spectroscopic signals, while keeping the sputtering yield for the Be main chamber walls unchanged.
|
|
| 26. |
|
|
| 27. |
- Parail, V., et al.
(författare)
-
Integrated modelling of ITER reference scenarios
- 2009
-
Ingår i: Nuclear Fusion. - : IOP Publishing. - 1741-4326 .- 0029-5515. ; 49:7
-
Tidskriftsartikel (refereegranskat)abstract
- The ITER Scenario Modelling Working Group (ISM WG) is organized within the European Task Force on Integrated Tokamak Modelling (ITM-TF). The main responsibility of the WG is to advance a pan-European approach to integrated predictive modelling of ITER plasmas with the emphasis on urgent issues, identified during the ITER Design Review. Three major topics are discussed, which are considered as urgent and where the WG has the best possible expertize. These are modelling of current profile control, modelling of density control and impurity control in ITER (the last two topics involve modelling of both core and SOL plasma). Different methods of heating and current drive are tested as controllers for the current profile tailoring during the current ramp-up in ITER. These include Ohmic, NBI, ECRH and LHCD methods. Simulation results elucidate the available operational margins and rank different methods according to their ability to meet different requirements. A range of ITER-relevant' plasmas from existing tokamaks were modelled. Simulations confirmed that the theory-based transport model, GLF23, reproduces the density profile reasonably well and can be used to assess ITER profiles with both pellet injection and gas puffing. In addition, simulations of the SOL plasma were launched using both H-mode and L-mode models for perpendicular transport within the edge barrier and in the SOL. Finally, an integrated approach was also used for the predictive modelling of impurity accumulation in ITER. This includes helium ash, extrinsic impurities (such as argon) and impurities coming from the wall (including tungsten). The relative importance of anomalous and neo-classical pinch contributions towards impurity penetration through the edge transport barrier and further accumulation in the core was assessed.
|
|
| 28. |
- Romanelli, M., et al.
(författare)
-
JINTRAC: A system of codes for integrated simulation of Tokamak scenarios
- 2014
-
Ingår i: Plasma and Fusion Research. - : Japan Society of Plasma Science and Nuclear Fusion Research. - 1880-6821. ; 9:SPECIALISSUE.2
-
Tidskriftsartikel (refereegranskat)abstract
- Operation and exploitation of present and future Tokamak reactors require advanced scenario modeling in order to optimize engineering parameters in the design phase as well as physics performance during the exploitation phase. The simulation of Tokamak scenarios involves simultaneous modeling of different regions of the reactor, characterized by different physics and symmetries, in order to predict quantities such as particle and energy confinement, fusion yield, power deposited on wall, wall load from fast particles. JINTRAC is a system of 25 interfaced Tokamak-physics codes for the integrated simulation of all phases of a Tokamak scenario. JINTRAC predictions reflect the physics and assumptions implemented in each module and extensive comparison with experimental data is needed to allow validation of the models and improvement of Tokamak-physics understanding. © 2014 The Japan Society of Plasma Science and Nuclear Fusion Research.
|
|
| 29. |
- Sauter, O., et al.
(författare)
-
Control of neoclassical tearing modes by sawtooth control
- 2002
-
Ingår i: Physical Review Letters. - 0031-9007 .- 1079-7114. ; 88:10
-
Tidskriftsartikel (refereegranskat)abstract
- The onset of a neoclassical tearing mode (NTM) depends on the existence of a large enough seed island. It is shown in the Joint European Torus that NTMs can be readily destabilized by long-period sawteeth, such as obtained by sawtooth stabilization from ion-cyclotron heating or current drive. This has important implications for burning plasma scenarios, as alpha particles strongly stabilize the sawteeth. It is also shown that, by adding heating and current drive just outside the inversion radius, sawteeth are destabilized, resulting in shorter sawtooth periods and larger beta values being obtained without NTMs.
|
|
| 30. |
- Solano, E. R., et al.
(författare)
-
Observation of Confined Current Ribbon in JET Plasmas
- 2010
-
Ingår i: Physical Review Letters. - 0031-9007 .- 1079-7114. ; 104:18, s. 185003-
-
Tidskriftsartikel (refereegranskat)abstract
- We report the identification of a localized current structure inside the JET plasma. It is a field-aligned closed helical ribbon, carrying current in the same direction as the background current profile (cocurrent), rotating toroidally with the ion velocity (corotating). It appears to be located at a flat spot in the plasma pressure profile, at the top of the pedestal. The structure appears spontaneously in low density, high rotation plasmas, and can last up to 1.4 s, a time comparable to a local resistive time. It considerably delays the appearance of the first edge localized mode.
|
|
| 31. |
- Westerhof, E., et al.
(författare)
-
Control of sawteeth and triggering of NTMs with ion cyclotron resonance frequency waves in JET
- 2002
-
Ingår i: Nuclear Fusion. - : IOP Publishing. - 0029-5515 .- 1741-4326. ; 42:11, s. 1324-1334
-
Tidskriftsartikel (refereegranskat)abstract
- A new scenario to delay or prevent neoclassical tearing mode (NTM) onset is presented. By active sawtooth destabilization, short period and low amplitude sawteeth are generated, such that the sawtooth produced NTM seed island is reduced and the threshold normalized plasma pressure for triggering of NTMs, beta(Nonset), is increased. The scenario has been explored experimentally in the Joint European Torus (JET). Ion cyclotron resonance frequency (ICRF) waves tuned to the 2nd harmonic H-minority resonance have been used for sawtooth control. Whereas ICRF waves generally induce sawtooth stabilization, favouring the triggering of NTMs and reducing beta(Nonset), the present experiments show that by toroidally directed waves, ion cyclotron current drive is produced, and that sawteeth can be destabilized by careful positioning of the 2nd harmonic H resonance layer with respect to the sawtooth inversion radius. As a result, NTM onset is delayed and beta(Nonset) is increased above its value obtained in discharges with additional heating from neutral beam injection alone.
|
|
| 32. |
- Nordman, Hans, 1957, et al.
(författare)
-
Modelling of impurity transport experiments at the Joint European Torus
- 2010
-
Ingår i: Proceedings of EPS 2010, Europhysics Conference Abstracts. - 2914771622 ; 34A
-
Konferensbidrag (refereegranskat)abstract
- Impurity transport in JET is studied using interpretative analysis and predictive simulations of JET discharges. The simulations are based on transport models for Ion-Temperature-Gradient (ITG) mode and Trapped-Electron (TE) mode driven turbulence and neoclassicaltransport. The properties of the impurity transport coefficients obtained with fluid as well as quasi-linear and nonlinear gyrokinetic simulations using the code GENE are compared and discussed. In particular, the sign of the impurity convective velocity (pinch) and the scaling of the normalised impurity density peaking factor -R∇nZ/nZ with impurity charge number is investigated. Predictive simulations of temperatures (Te, Ti=TZ) and densities (ne,nZ) are performed with the JETTO/SANCO core transport code.The scaling of impurity transport with impurity charge Z is crucial for the performance and optimisation of a fusion reactor. In the present study, a set of dedicated JET impurity injection experiments are analysed. The impurities were injected by laser ablation (Ni) and gas injection (Ne, Ar) and the diffusivity DZ and convective velocity VZ were determined by matching spectroscopic data with predictive results obtained with the transport code UTC-SANCO.
|
|
| 33. |
- Tegnered, Daniel, 1987, et al.
(författare)
-
Predictive simulations of impurity transport at JET
- 2013
-
Konferensbidrag (refereegranskat)abstract
- Impurity transport in the Joint European Torus is analysed using the coupling between the transport codes JETTO (for main ions) and SANCO (for impurities) for predictive simulations of dedicated impurity injection experiments. The experimentally injected trace levels of Ne, Ar and Ni in a 2% C background are considered together with numerical experiments covering a broad range of impurities from Be to W. Transport coefficients due to Ion-Temperature-Gradient (ITG) mode and Trapped-Electron (TE) mode turbulence are used together with neoclassical transport from NCLASS. The transport coefficients obtained using the Chalmers fluid model are compared with gyrokinetic results using the code GENE. An updated, multiple ion species version of the Chalmers model called EDWM (Extended Drift Wave Model) has been used for the transport coefficients. Self-consistent simulations of electron and ion temperatures, main ion and impurity densities and toroidal momentum are performed. The role of neoclassical impurity transport is evaluated and the dependence of the simulated profiles on impurity charge number Z, collisionality, ExB shearing, rotation gradient (roto-diffusion), and impurity charge fraction (Zeff) are discussed. For the NBI heated JET L-mode discharges considered, the predictive simulations show that the impurity transport in the bulk of the plasma is dominated by ITG driven transport resulting in impurity peaking factors substantially below the neoclassical predictions for low to intermediate charge numbers. For larger Z-values as well as in the inner core region (ρ
|
|
