| 1. |
- Munthe, Christian, 1962
(författare)
-
Precaution and Ethics: Handling risks, uncertainties and knowledge gaps in the regulation of new biotechnologies
- 2017
-
Bok (övrigt vetenskapligt/konstnärligt)abstract
- This volume outlines and analyses ethical issues actualized by applying a precautionary approach to the regulation of new biotechnologies. It presents a novel way of categorizing and comparing biotechnologies from a precautionary standpoint. Based on this, it addresses underlying philosophical problems regarding the ethical assessment of decision-making under uncertainty and ignorance, and discusses how risks and possible benefits of such technologies should be balanced from an ethical standpoint. It argues on conceptual and ethical grounds for a technology neutral regulation as well as for a regulation that not only checks new technologies but also requires old, inferior ones to be phased out. It demonstrates how difficult ethical issues regarding the extent and ambition of precautionary policies need to be handled by such a regulation, and presents an overarching framework for doing so.
|
|
| 2. |
- Skoog, Emma, 1983, et al.
(författare)
-
Biobased adipic acid – The challenge of developing the production host
- 2018
-
Ingår i: Biotechnology Advances. - : Elsevier BV. - 0734-9750. ; 36:8, s. 2248-2263
-
Forskningsöversikt (refereegranskat)abstract
- Adipic acid is a platform chemical, and is the most important commercial dicarboxylic acid. It has been targeted for biochemical conversion as an alternative to present chemical production routes. From the perspective of bioeconomy, several kinds of raw material are of interest including the sugar platform (derived from starch, cellulose or hemicellulose), the lignin platform (aromatics) and the fatty acid platform (lipid derived). Two main biochemical-based production schemes may be employed: (i) direct fermentation to adipic acid, or (ii) fermentation to muconic or glucaric acid, followed by chemical hydrogenation (indirect fermentation). This review presents a comprehensive description of the metabolic pathways that could be constructed and analyzes their respective theoretical yields and metabolic constraints. The experimental yields and titers obtained so far are low, with the exception of processes based on palm oil and glycerol, which have been reported to yield up to 50 g and 68 g adipic acid/L, respectively. The challenges that remain to be addressed in order to achieve industrially relevant production levels include solving redox constraints, and identifying and/or engineering enzymes for parts of the metabolic pathways that have yet to be metabolically demonstrated. This review provides new insights into ways in which metabolic pathways can be constructed to achieve efficient adipic acid production. The production host provides the chassis to be engineered via an appropriate metabolic pathway, and should also have properties suitable for the industrial production of adipic acid. An acidic process pH is attractive to reduce the cost of downstream processing. The production host should exhibit high tolerance to complex raw material streams and high adipic acid concentrations at acidic pH.
|
|
| 3. |
- Anasontzis, George E, 1980
(författare)
-
Biomass modifying enzymes: From discovery to application
- 2012
-
Ingår i: Oral presentation at the Chalmers Life Science AoA conference.
-
Konferensbidrag (övrigt vetenskapligt/konstnärligt)abstract
- It has now been realized that the road towards the bio-based economy is a one-way street, leaving gradually the oil-based technology and driving slowly towards a more sustainable society. The current non-biodegradable hydrocarbon fuels and plastics will be replaced by new products which will derive from natural and renewable resources. The synthesis of such biofuels and biochemicals is still challenged by the difficulties to cost efficiently degrade lignocellulosic material to fermentable sugars or to isolate the intact polymers. Biomass degrading and modifying enzymes play an integral role both in the separation of the polymers from the wood network, as well as in their subsequent modification, prior to further product development.Our group interests focus on all levels of applied enzyme research of biomass acting enzymes: Discovery, assay development, production and application. Relevant examples will be provided: What is our strategy for discovering novel microorganisms and enzymes from the tropical forests and grasslands of Vietnam? How do we design novel real-world assays for enzyme activity determination? Which are the bottlenecks in the enzymatic cellulose hydrolysis? How enzymes can be used to produce high added value compounds from biomass?
|
|
| 4. |
- Wang, Shule, 1994-, et al.
(författare)
-
Effect of H2 as Pyrolytic Agent on the Product Distribution during Catalytic Fast Pyrolysis of Biomass Using Zeolites
- 2018
-
Ingår i: Energy & Fuels. - : American Chemical Society (ACS). - 0887-0624 .- 1520-5029. ; 32:8, s. 8530-8536
-
Tidskriftsartikel (refereegranskat)abstract
- Bio-oil generated from catalytic fast pyrolysis or hydrotreating processes represents one of the most promising alternatives to liquid fossil fuels. The use of H2 as carrier gas in the pyrolysis of biomass requires further research to study the catalytic fast pyrolysis reactions in the case of using reactive atmosphere. In this work, pyrolysis experiments with lignocellulosic biomass have been performed in a fixed bed reactor in H2 and N2 atmospheres with/without HZSM-5 additions to investigate the influence of the pyrolytic agents during fast pyrolysis of biomass and upgrading of pyrolytic vapors over a zeolitic catalyst. It was found that in a H2 atmosphere, H2 was consumed in both noncatalytic and catalytic pyrolysis processes, respectively. Higher yields of nonaqueous liquids and permanent gases are obtained in a H2 atmosphere compared to a N2 atmosphere. A catalytic pyrolysis process using HZSM-5 in a H2 atmosphere increased the production of polymer aromatic hydrocarbons and suppressed the production of monomer aromatic hydrocarbons compared to similar tests performed in a N2 atmosphere. The results show an overall increased activity of HZSM-5 in the reactive H2 atmosphere compared to a N2 atmosphere.
|
|
| 5. |
- Nickel, David, 1990
(författare)
-
Process development for platform chemical production from agricultural and forestry residues
- 2021
-
Doktorsavhandling (övrigt vetenskapligt/konstnärligt)abstract
- As part of a bio-based economy, biorefineries are envisaged to sustainably produce platform chemicals via biochemical conversion of agricultural and forestry residues. However, supply risks, the recalcitrance of lignocellulosic biomass, and inhibitor formation during pretreatment impair the economic feasibility of such biorefineries. In this thesis, process design and assessment were developed with the aim of addressing these hurdles and improving the cost-effectiveness of lignocellulose-derived platform chemicals. To expand the feedstock base and reduce operational costs, logging residues served as underutilised and inexpensive raw material. The major impediment in converting logging residues was their high recalcitrance and low cellulose content, which resulted in low attainable ethanol titres during simultaneous saccharification and co-fermentation (SSCF). Pretreatment optimisation reduced inhibitor formation and recalcitrance, and led to enzymatic hydrolysis yields at par with those obtained for stem wood, despite the less favourable chemical composition. Upgrading logging residues with carbohydrate-rich oat hulls increased ethanol titres to >50 g/L using batch SSCF at 20% WIS loadings, demonstrating the potential to further decrease downstream processing costs. To alleviate the toxicity of inhibitors generated during pretreatment, preadaptation was applied to Saccharomyces cerevisiae . Exposure to the inhibitors in the pretreated liquid fraction improved ethanol production during subsequent fermentation. Transferring the concept of preadaptation to lactic acid production by Bacillus coagulans cut the process times by half and more than doubled the average specific lactic acid productivity, showcasing how preadaptation could decrease operational costs. To assess the performance and robustness of process designs against process input variations, a multi-scale variability analysis framework was developed. The framework included models for bioprocess, flowsheet, techno-economic, and life cycle assessment. In a case study, multi-feed processes, in which solids and cells are fed to the process using model-based predictions, were more robust against variable cellulolytic activities than batch SSCFs in a wheat straw-based ethanol biorefinery. The developed framework can be used to identify robust biorefinery process designs, which simultaneously meet technological, economic, and environmental goals.
|
|
| 6. |
|
|
| 7. |
- McKee, Lauren S., et al.
(författare)
-
A GH115 alpha-glucuronidase from Schizophyllum commune contributes to the synergistic enzymatic deconstruction of softwood glucuronoarabinoxylan
- 2016
-
Ingår i: Biotechnology for Biofuels. - : BioMed Central. - 1754-6834. ; 9
-
Tidskriftsartikel (refereegranskat)abstract
- Background: Lignocellulosic biomass from softwood represents a valuable resource for the production of biofuels and bio-based materials as alternatives to traditional pulp and paper products. Hemicelluloses constitute an extremely heterogeneous fraction of the plant cell wall, as their molecular structures involve multiple monosaccharide components, glycosidic linkages, and decoration patterns. The complete enzymatic hydrolysis of wood hemicelluloses into monosaccharides is therefore a complex biochemical process that requires the activities of multiple degradative enzymes with complementary activities tailored to the structural features of a particular substrate. Glucuronoarabinoxylan (GAX) is a major hemicellulose component in softwood, and its structural complexity requires more enzyme specificities to achieve complete hydrolysis compared to glucuronoxylans from hardwood and arabinoxylans from grasses. Results: We report the characterisation of a recombinant alpha-glucuronidase (Agu115) from Schizophyllum commune capable of removing (4-O-methyl)-glucuronic acid ((Me) GlcA) residues from polymeric and oligomeric xylan. The enzyme is required for the complete deconstruction of spruce glucuronoarabinoxylan (GAX) and acts synergistically with other xylan-degrading enzymes, specifically a xylanase (Xyn10C), an alpha-l-arabinofuranosidase (AbfA), and a beta-xylosidase (XynB). Each enzyme in this mixture showed varying degrees of potentiation by the other activities, likely due to increased physical access to their respective target monosaccharides. The exo-acting Agu115 and AbfA were unable to remove all of their respective target side chain decorations from GAX, but their specific activity was significantly boosted by the addition of the endo-Xyn10C xylanase. We demonstrate that the proposed enzymatic cocktail (Agu115 with AbfA, Xyn10C and XynB) achieved almost complete conversion of GAX to arabinofuranose (Araf), xylopyranose (Xylp), and MeGlcA monosaccharides. Addition of Agu115 to the enzymatic cocktail contributes specifically to 25 % of the conversion. However, traces of residual oligosaccharides resistant to this combination of enzymes were still present after deconstruction, due to steric hindrances to enzyme access to the substrate. Conclusions: Our GH115 alpha-glucuronidase is capable of finely tailoring the molecular structure of softwood GAX, and contributes to the almost complete saccharification of GAX in synergy with other exo- and endo-xylan-acting enzymes. This has great relevance for the cost-efficient production of biofuels from softwood lignocellulose.
|
|
| 8. |
- Olofsson, Martin, 1975-, et al.
(författare)
-
Combined Effects of Nitrogen Concentration and Seasonal Changes on the Production of Lipids in Nannochloropsis oculata
- 2014
-
Ingår i: Marine Drugs. - Basel, Switzerland : MDPI AG. - 1660-3397. ; 12:4, s. 1891-1910
-
Tidskriftsartikel (refereegranskat)abstract
- Instead of sole nutrient starvation to boost algal lipid production, we addressed nutrient limitation at two different seasons (autumn and spring) during outdoor cultivation in flat panel photobioreactors. Lipid accumulation, biomass and lipid productivity and changes in fatty acid composition of Nannochloropsis oculata were investigated under nitrogen (N) limitation (nitrate:phosphate N:P 5, N:P 2.5 molar ratio). N. oculata was able to maintain a high biomass productivity under N-limitation compared to N-sufficiency (N:P 20) at both seasons, which in spring resulted in nearly double lipid productivity under N-limited conditions (0.21 g L−1 day−1) compared to N-sufficiency (0.11 g L−1 day−1). Saturated and monounsaturated fatty acids increased from 76% to nearly 90% of total fatty acids in N-limited cultures. Higher biomass and lipid productivity in spring could, partly, be explained by higher irradiance, partly by greater harvesting rate (~30%). Our results indicate the potential for the production of algal high value products (i.e., polyunsaturated fatty acids) during both N-sufficiency and N-limitation. To meet the sustainability challenges of algal biomass production, we propose a dual-system process: Closed photobioreactors producing biomass for high value products and inoculum for larger raceway ponds recycling waste/exhaust streams to produce bulk chemicals for fuel, feed and industrial material.
|
|
| 9. |
|
|
| 10. |
- Shin, Jae Ho, 1987, et al.
(författare)
-
Molecular docking and linear interaction energy studies give insight to α, β-reduction of enoate groups in enzymes
- 2018
-
Konferensbidrag (övrigt vetenskapligt/konstnärligt)abstract
- Production of adipic acid from renewable sources has been gaining attention in an attempt to move from an oil-based economy to a biobased economy. Metabolic engineering allows microorganisms to produce useful chemicals using renewable resources as carbon sources. We target a theoretical metabolic pathway that relies on conversion of L-lysine to adipic acid. One of the enzymatic steps in this conversion pathway is an α, β-reduction of an unsaturated bond in an enoate moiety and no aerobic enzymes have been identified to specifically make this conversion on 6-amino-trans-2-hexenoic acid. We evaluated Escherichia coli NemA, and Saccharomyces pastorianus Oye1 (Old Yellow Enzyme 1) for their potenstial capability to carry out the desired α, β-reduction. Here, we build homology models for E. coli NemA and perform molecular docking studies of trans-2-hexenoic acid and trans-2-hexenal to the candidate enzyme models. Ligand-enzyme binding stability is assessed by molecular dynamics (MD) simulations. Additionally, linear energy calculations were used to investigate binding stability in solution environment. Here, we propose that NemA and Oye1, both belonging to the Old yellow enzyme family, have large enough catalytic pocket for accommodating enoate moieties but not enough stability to carry out the α, β-reduction. Protein engineering of both NemA and Oye1 would be necessary for these enzymes to perform the targeted reactions efficiently. The results shown in this study provides a useful insight to α, β-reduction reaction potentially crucial in bio-based production of adipic acid.
|
|
| 11. |
- Zhou, Yongjin, 1984, et al.
(författare)
-
Production of fatty acid-derived oleochemicals and biofuels by synthetic yeast cell factories
- 2016
-
Ingår i: Nature Communications. - : Springer Science and Business Media LLC. - 2041-1723 .- 2041-1723. ; 7, s. 11709-11709
-
Tidskriftsartikel (refereegranskat)abstract
- Sustainable production of oleochemicals requires establishment of cell factory platform strains. The yeast Saccharomyces cerevisiae is an attractive cell factory as new strains can be rapidly implemented into existing infrastructures such as bioethanol production plants. Here we show high-level production of free fatty acids (FFAs) in a yeast cell factory, and the production of alkanes and fatty alcohols from its descendants. The engineered strain produces up to 10.4 g/L of FFAs, which is the highest reported titre to date. Furthermore, through screening of specific pathway enzymes, endogenous alcohol dehydrogenases and aldehyde reductases, we reconstruct efficient pathways for conversion of fatty acids to alkanes (0.8 mg /L) and fatty alcohols (1.5 g/L), to our knowledge the highest titres reported in S. cerevisiae. This should facilitate the construction of yeast cell factories for production of fatty acids derived products and even aldehyde-derived chemicals of high value.
|
|
| 12. |
- Karlsson, Emma, 1983, et al.
(författare)
-
In silico and in vitro studies of the reduction of unsaturated α,β bonds of trans-2-hexenedioic acid and 6-amino-trans-2-hexenoic acid – Important steps towards biobased production of adipic acid
- 2018
-
Ingår i: PLoS ONE. - : Public Library of Science (PLoS). - 1932-6203 .- 1932-6203. ; 13:2
-
Tidskriftsartikel (refereegranskat)abstract
- The biobased production of adipic acid, a precursor in the production of nylon, is of great interest in order to replace the current petrochemical production route. Glucose-rich lignocel-lulosic raw materials have high potential to replace the petrochemical raw material. A number of metabolic pathways have been proposed for the microbial conversion of glucose to adipic acid, but achieved yields and titers remain to be improved before industrial applications are feasible. One proposed pathway starts with lysine, an essential metabolite industrially produced from glucose by microorganisms. However, the drawback of this pathway is that several reactions are involved where there is no known efficient enzyme. By changing the order of the enzymatic reactions, we were able to identify an alternative pathway with one unknown enzyme less compared to the original pathway. One of the reactions lacking known enzymes is the reduction of the unsaturated α,β bond of 6-amino-trans-2-hexenoic acid and trans-2hexenedioic acid. To identify the necessary enzymes, we selected N-ethylmaleimide reductase from Escherichia coli and Old Yellow Enzyme 1 from Saccharomyces pastorianus. Despite successful in silico docking studies, where both target substrates could fit in the enzyme pockets, and hydrogen bonds with catalytic residues of both enzymes were predicted, no in vitro activity was observed. We hypothesize that the lack of activity is due to a difference in electron withdrawing potential between the naturally reduced aldehyde and the carboxylate groups of our target substrates. Suggestions for protein engineering to induce the reactions are discussed, as well as the advantages and disadvantages of the two metabolic pathways from lysine. We have highlighted bottlenecks associated with the lysine pathways, and proposed ways of addressing them.
|
|
| 13. |
- Gontia, Paul, 1984, et al.
(författare)
-
Life cycle assessment of bio-based sodium polyacrylate production from pulp mill side streams: Case study of thermo-mechanical and sulfite pulp mills
- 2016
-
Ingår i: Journal of Cleaner Production. - : Elsevier BV. - 0959-6526. ; 131, s. 475-484
-
Tidskriftsartikel (refereegranskat)abstract
- Sodium polyacrylate (Na-PA) is a super absorbent polymer, which is commonly used in diverse hygiene products. The polymer is currently produced from fossil feedstock and its production consequently leads to adverse environmental impacts. Na-PA production from sugars present in pulp mill side streams can potentially be a successful way to achieve a more sustainable production of this polymer. In order to guide the development of a novel biochemical process for producing Na-PA, a life cycle assessment was done in which Na-PA produced from side streams of thermo-mechanical pulp (TMP) and sulfite pulp mills were compared. Furthermore, a comparison was made with Na-PA produced from fossil resources. The results show that the main determinant of the environmental impact of the bio-based Na-PA production is the free sugar content in the side streams. The lowest environmental impact is achieved by the least diluted side streams. More diluted side streams require larger amounts of energy for concentration, and, if the diluted streams are not concentrated, processes such as hydrolysis and detoxification, and fermentation are the environmental hotspots. Furthermore, the higher the yield of the fermentation process, the lower the environmental impact will be. Lastly, the production of bio-based Na-PA led to a lower global warming potential for some of the considered pulp mill side streams, but all of the other impacts considered were higher, when compared to fossil-based Na-PA production. Therefore, in parallel with efforts to develop a high-yield yeast for the fermentation process, technology developers should focus on low energy concentration processes for the side streams.
|
|
| 14. |
- Adeboye, Peter, 1982, et al.
(författare)
-
DETOXIFICATION AS A STRATEGY FOR DEVELOPING TOLERANCE IN Saccharomyces cerevisiae TO PHENOLIC COMPOUNDS
- 2014
-
Ingår i: ISSY31: 31ST INTERNATIONAL SPECIALISED SYMPOSIUM ON YEAST.
-
Konferensbidrag (övrigt vetenskapligt/konstnärligt)abstract
- Several phenolic compounds are formed as products of lignin breakdown during pretreatment of lignocellulosic biomass. These phenolic compounds are inhibitory to cell growth and function as biocatalysts in the production of second generation biofuels from degraded lignocellulosic biomass. Our research is focused on developing a Saccharomyces cerevisiae strain with improved resistance to phenolic compounds.As part of our study, we have focused on understanding the ability of S. cerevisiae to tolerate and convert phenolic compounds. We aim to understand the conversion mechanisms of phenolic compounds and adapt the knowledge to the engineering and use of S. cerevisiae on a biotechnological platform for bioethanol production and prospective, novel bio-based chemicals.We have investigated toxicity of various phenolic compounds against S. cerevisiae. Our results showed that phenolic compounds have varied toxicity against S. cerevisiae and the toxicity may be dependent on the structure of the compound involved. Under aerobic batch cultivation conditions, we have also studied the conversion of phenolic compounds by S. cerevisiae using coniferyl aldehyde, ferulic acid and p-coumaric acid as representative phenolic compounds. We compiled a list of conversion products of the three starting compounds under investigation and we proposed a possible conversion pathway, currently being investigated.In this talk, we present the proposed conversion pathway through which S. cerevisiae converts and detoxifies coniferyl aldehyde, ferulic acid and p-coumaric acid under aerobic cultivation condition.
|
|
| 15. |
- Amiandamhen, Stephen, 1983-, et al.
(författare)
-
Bioenergy production and utilization in different sectors in Sweden: A state of the art review
- 2020
-
Ingår i: BioResources. - : University of North Carolina Press. - 1930-2126. ; 15:4, s. 9834-9857
-
Forskningsöversikt (refereegranskat)abstract
- In the continual desire to reduce the environmental footprints of human activities, research efforts to provide cleaner energy is increasingly becoming vital. The effect of climate change on present and future existence, sustainable processes, and utilizations of renewable resources have been active topics within international discourse. In order to reduce the greenhouse gases emissions from traditional materials and processes, there has been a shift to more environmental friendly alternatives. The conversion of biomass to bioenergy, including biofuels has been considered to contribute to the future of climate change mitigation, although there are concerns about carbon balance from forest utilization. Bioenergy accounts for more than one-third of all energy used in Sweden and biomass has provided about 60% of the fuel for district heating. Apart from heat and electricity supply, the transport sector, with about 30% of global energy use, has a significant role in a sustainable bioenergy system. This review presents the state of the art in the Swedish bioenergy sector based on literature and Swedish Energy Agency’s current statistics. The review also discusses the overall bioenergy production and utilization in different sectors in Sweden. The current potential, challenges, and environmental considerations of bioenergy production are also discussed.
|
|
| 16. |
- Brink, Daniel
(författare)
-
Understanding and improving microbial cell factories through Large Scale Data-approaches
- 2019
-
Doktorsavhandling (övrigt vetenskapligt/konstnärligt)abstract
- Since the advent of high-throughput genome sequencing methods in the mid-2000s, molecular biology has rapidly transitioned towards data-intensive science. Recent technological developments have increased the accessibility of omics experiments by decreasing the cost, while the concurrent design of new algorithms have improved the computational work-flow needed to analyse the large datasets generated. This has enabled the long standing idea of a systems approach to the cell, where molecular phenomena are no longer observed in isolation, but as parts of a tightly regulated cell-wide system. However, large data biology is not without its challenges, many of which are directly related to how to store, handle and analyse ome-wide datasets.The present thesis examines large data microbiology from a middle ground between metabolic engineering and in silico data management. The work was performed in the context of applied microbial lignocellulose valorisation with the end goal of generating improved cell factories for the production of value-added chemicals from renewable plant biomass. Three different challenges related to this feedstock were investigated from a large data-point of view: bacterial catabolism of lignin and its derived aromatic compounds; tolerance of baker’s yeast Saccharomyces cerevisiae to inhibitory compounds in lignocellulose hydrolysate; and the non-fermentable response to xylose in S. cerevisiae engineered for growth on this pentose sugar.The bibliome of microbial lignin catabolism is vast and consists of a long-standing cohort of fundamental microbiology, and a more recent cohort of applied lignin biovalorisation. Here, an online database was created with the long-term ambition of closing the gap between the two and make new connections that can fuel the generation of new knowledge. Whole-genome sequencing was used to investigate the genetic basis for observed phenotypes in bacterial isolates capable of growing on different kinds of lignin-derived aromatics. A whole-genome approach was also used to identify key sequence variants in the genotype of an industrial S. cerevisiae strain evolved for improved tolerance to inhibitors and high temperature. Finally, assessment of the sugar signalome of S. cerevisiae was enabled by the design and validation of a panel of in vivo fluorescent biosensors for single-cell cytometric analysis. It was found that xylose triggered a signal similar to that of low glucose in yeast cells engineered with xylose utilization pathways, and that introduction of deletions previously related to improved xylose utilization altered the signal towards that of high glucose.Taken together, the present thesis illustrates how omics-approaches can aid design of laboratory experiments to increase the knowledge and understanding of microorganisms, and demonstrates the need for a combined knowledge of molecular and computational biology in large-scale data microbiology.
|
|
| 17. |
- Marx, Christian, 1975, et al.
(författare)
-
ENGINEERING GLUTATHIONE BIOSYNTHESIS TO ENHANCE REDOX ROBUSTNESS OF Saccharomyces cerevisiae
- 2014
-
Ingår i: ISSY31: 31ST INTERNATIONAL SPECIALISED SYMPOSIUM ON YEAST.
-
Konferensbidrag (övrigt vetenskapligt/konstnärligt)abstract
- The focus for biofuel production shifts to using lignocellulose biomass from forest and agricultural by-products since it does not compete with food and feed production. Polysaccharides must be pretreated to be made accessible to hydrolytic enzymes to generate monomeric sugars for the following fermentation. In this pretreatment step inhibitors of fermenting microorganisms are generated, mainly furan derivates, weak acids and phenolics. Although Saccharomyces cerevisiae is more robust than bacteria, there is demand for improvement and the development of novel yeast strains with increased inhibitor tolerance is highly desirable.Furan derivates and other inhibitors have been shown to induce the formation of reactive oxygen species. Engineering of the redox metabolism of S. cerevisiae in terms of increasing the intracellular levels of glutathione by overexpressing glutathione synthetase GSH1 resulted in increased strain robustness in a simultaneous saccharification and fermentation (SSF) process. Cell survival and final ethanol concentrations were increased in the recombinant strains compared to the wild type in industrial media [Ask et al. 2013].To show a correlation between the intracellular concentration of glutathione and the resulting effect on robustness, strains accumulating different amounts of glutathione will be created. GshF is a bi-functional enzyme found in several bacterial species, that catalyzes the formation of glutathione from its precursors without accumulation of the intermediate product γ- glutamylcysteine and without any relevant feedback inhibition. GshF will be overexpressed in a CEN.PK strain, followed by deletion of the native GSH1 and GSH2 enzymes catalyzing the two-step reaction in S. cerevisiae.
|
|
| 18. |
- Xiros, Charilaos, 1973, et al.
(författare)
-
Toward a sustainable biorefinery using high-gravity technology
- 2017
-
Ingår i: Biofuels, Bioproducts and Biorefining. - : Wiley. - 1932-1031 .- 1932-104X. ; 11:1, s. 15-27
-
Tidskriftsartikel (refereegranskat)abstract
- The realization of process solutions for a sustainable bioeconomy depends on the efficient processing of biomass. High-gravity technology is one important alternative to realizing such solutions. The aims of this work were to expand the knowledge-base on lignocellulosic bioconversion processes at high solids content, to advance the current technologies for production of second-generation liquid biofuels, to evaluate the environmental impact of the proposed process by using life cycle assessment (LCA), and to develop and present a technically, economically, and environmentally sound process at high gravity, i.e., a process operating at the highest possible concentrations of raw material. The results and opinions presented here are the result of a Nordic collaborative study within the framework of the HG Biofuels project. Processes with bioethanol or biobutanol as target products were studied using wheat straw and spruce as interesting Nordic raw materials. During the project, the main scientific, economic, and technical challenges of such a process were identified. Integrated solutions to these challenges were proposed and tested experimentally, using wheat straw and spruce wood at a dry matter content of 30% (w/w) as model substrates. The LCA performed revealed the environmental impact of each of the process steps, highlighting the importance of the enzyme dose used for the hydrolysis of the plant biomass, as well as the importance of the fermentation yield.
|
|
| 19. |
- Aulitto, Martina, 1991, et al.
(författare)
-
Seed culture pre-adaptation of Bacillus coagulans MA-13 improves lactic acid production in simultaneous saccharification and fermentation
- 2019
-
Ingår i: Biotechnology for Biofuels. - : Springer Science and Business Media LLC. - 1754-6834 .- 1754-6834. ; 12:1
-
Tidskriftsartikel (refereegranskat)abstract
- Background Lignocellulosic biomass is an abundant and sustainable feedstock, which represents a promising raw material for the production of lactic acid via microbial fermentation. However, toxic compounds that affect microbial growth and metabolism are released from the biomass upon thermochemical pre-treatment. So far, susceptibility of bacterial strains to biomass-derived inhibitors still represents a major barrier to lactic acid production from lignocellulose. Detoxification of the pre-treated lignocellulosic material by water washing is commonly performed to alleviate growth inhibition of the production microorganism and achieve higher production rates. Results In this study, we assessed the feasibility of replacing the washing step with integrated cellular adaptation during pre-culture of Bacillus coagulans MA-13 prior to simultaneous saccharification and lactic acid fermentation of steam exploded wheat straw. Using a seed culture pre-exposed to 30% hydrolysate led to 50% shorter process time, 50% higher average volumetric and 115% higher average specific productivity than when using cells from a hydrolysate-free seed culture. Conclusions Pre-exposure of B. coagulans MA-13 to hydrolysate supports adaptation to the actual production medium. This strategy leads to lower process water requirements and combines cost-effective seed cultivation with physiological pre-adaptation of the production strain, resulting in reduced lactic acid production costs.
|
|
| 20. |
|
|
| 21. |
- Adeboye, Peter, 1982, et al.
(författare)
-
Conversion of lignin-derived phenolic compounds by Saccharomyces cerevisiae
- 2014
-
Ingår i: 36th Symposium on Biotechnology for Fuels and Chemicals, April 2-May 1st, Clearwater Beach, Florids, USA.
-
Konferensbidrag (övrigt vetenskapligt/konstnärligt)abstract
- Lignin breakdown during biomass pretreatment releases a wide array of phenolic compounds in lignocellulose hydrolysates. Phenolic compounds, together with organic acids and furaldehydes are known to be inhibitors of microbial fermentation, thus limiting the efficient bioconversion of lignocellulose biomass. The goal of our study is to improve S. cerevisiae tolerance to phenolic compounds from lignocellulose hydrolysates and investigate its conversion capacities. In particular, we aimed i) to establish a correlation between the phenolic compounds structure and the effect on yeast growth, and ii) to investigate the conversion/detoxification products of selected representative compounds in order to provide strain engineering strategies for enhanced phenolics conversion.First, the effect on S. cerevisiae growth of 13 different phenolic compounds commonly found in lignocellulose hydrolysates was characterized. The compounds could be grouped in three clusters, according to their effect on lag phase duration, specific growth rate and cell density. Next, coniferyl aldehyde, p-coumaric acid and ferulic acid were chosen as representative compounds and their conversion product by S. cerevisiae in aerobic culture in bioreactor were identified and followed throughout the fermentation time. Understanding the effect of different phenolics on yeast and their conversion/ detoxification pathways is the first step not only in strain engineering for enhanced robustness, but also for designing new biorefinery concepts, where the bioconversion of lignin-derived aromatics could potentially be the source of new bio-based chemicals.
|
|
| 22. |
- Bettiga, Maurizio, 1978, et al.
(författare)
-
Yeast physiology studies and metabolic engineering for enhanced robustness
- 2014
-
Ingår i: Enzitec 2014- XI Seminário Brasileiro de Tecnologia Enzimática. Barra da Tijuca-Rio de Janeiro, April 14th to 16th, 2014.
-
Konferensbidrag (övrigt vetenskapligt/konstnärligt)abstract
- The extensive research on second-generation ethanol has paved the way to a new concept of bio-based industry, where lignocellulosic material is the primary source of sugars, to be converted to a number of fuels and chemicals. Sugars are released from cellulose and hemicellulose by pretreatment and hydrolysis steps. Harsh conditions during pretreatment promote the formation of a number of inhibitory compounds, among which weak organic acids, furaldehydes and phenolic compounds. In addition, the product of interest can act as a potent inhibitor. Regardless of the product, robust microorganisms are a prerequisite for the feasibility of lignocellulose-based bioprocesses.Current research carried out by our group focuses on the yeast Saccharomyces cerevisiae and aims at investigating the molecular bases of microbial robustness. Our efforts include the identification of the molecular targets of different classes of fermentation inhibitors aiming at understanding the complex responses of the cells to these compounds. The final goal is to engineer more robust strains. The concept of robustness will be discussed and examples of key features for S. cerevisiae robustness as well as examples of successful engineering to increase robustness will be presented.In particular, during this presentation, the following results will be discussed i) the study of redox and energy metabolism as key determinants of tolerance; ii) conversion routes of in S. cerevisiae as a way of detoxification from phenolic compounds; iii) cell membrane engineering as a strategy to achieve enhanced tolerance to weak acids.
|
|
| 23. |
- Modin, Oskar, 1980, et al.
(författare)
-
Opportunities for microbial electrochemistry in municipal wastewater treatment – an overview
- 2014
-
Ingår i: Water Science and Technology. - : IWA Publishing. - 0273-1223 .- 1996-9732. ; 69:7, s. 1359-1372
-
Tidskriftsartikel (refereegranskat)abstract
- Microbial bioelectrochemical systems (BESs) utilise living microorganisms to drive oxidation and reduction reactions at solid electrodes. BESs could potentially be used at municipal wastewater treatment plants (WWTPs) to recover the energy content of organic matter, to produce chemicals useful at the site, or to monitor and control biological treatment processes. In this paper, we review bioelectrochemical technologies that could be applied for municipal wastewater treatment. Sjölunda WWTP in Malmö, Sweden, is used as an example to illustrate how the different technologies potentially could be integrated in an existing treatment plant and the impact they could have on the plant’s utilization of energy and chemicals.
|
|
| 24. |
|
|
| 25. |
- Bonzom, Cyrielle, 1987, et al.
(författare)
-
Feruloyl esterases immobilization in mesoporous silica particles
- 2016
-
Konferensbidrag (övrigt vetenskapligt/konstnärligt)abstract
- Mesoporous silica materials (MPS) are an interesting choice as support to immobilize enzymes because MPS offer unique properties such as high enzyme loading and tunable pore size. They also provide the enzyme with a sheltered environment therefore reducing loss of function in industrial applications.Feruloyl esterases (FAEs) are naturally hydrolytic enzymes which are known for their action on lignocellulosic material and release ferulic acid (FA) which is bound to plant cell wall materials. Under specific conditions they are also able to perform synthetic reactions. In our work we focused on performing transesterification reactions with FAEs. The synthesis of butyl ferulate (BFA) from methyl ferulate (MFA) was chosen as a model reaction.Reduced water content of the reaction system, needed for the transesterification reaction to happen, can be achieved by replacing buffer with solvents. However, solvents can have a deleterious effect on the biocatalyst. Therefore, the use of ionic liquids instead of solvents was investigated. In addition, the enzymes were immobilized on MPS. In order to achieve a good immobilization yield and a good immobilized activity of the FAEs, several parameters were varied, and enzyme activity and selectivity were assessed. Since the reaction of interest was transesterification, the selectivity of the enzyme was quantified by determining the molar ratio between the product of transesterification reaction and the product of hydrolysis reaction: BFA/FA. Kinetic parameters, stability and reusability of the immobilized biocatalyst were also investigated. We found that the properties of enzyme themselves influence the immobilization process as well as the enzyme performance. Enzymes having a different isoelectric point or bearing different surface modifications such as glycosylations have different behaviors both in terms of enzyme activity and of immobilization performance.
|
|
| 26. |
- Janssen, Mathias, 1973, et al.
(författare)
-
Guiding technology development using LCA: The case of bio-based adipic acid production
- 2015
-
Ingår i: ISIE Conference 2015.
-
Konferensbidrag (refereegranskat)abstract
- Moving from a fossil-based to a bio-based economy requires the development of new technologies for the production of bio-based chemicals and materials. These technologies may become part of novel biorefinery concepts that combine the production of bulk and fine chemicals. This paper presents a life cycle assessment (LCA) of such a novel concept in which forest residues and micro-algae are used as feedstock for the combined production of adipic acid and high value-added chemicals. Adipic acid is mainly used as a precursor in the production of nylon, and its current fossil-based production process emits significant quantities of nitrous oxide (N2O), a highly potent greenhouse gas. There is thus a great potential to reduce the global warming potential of the production of adipic acid, and consequently nylon.The novel biorefinery concept is the main target of a multi-disciplinary R&D project. The concept is in a very early stage of development which mostly consists of experimental lab work. There are some challenges that must be overcome to evaluate the concept using life cycle assessment at this early development stage. Scaling up lab results to an industrially relevant process capacity needs to be addressed in order to e.g. account for changes in yield. This can be done using process modeling and simulation. The total scale of production is another aspect which is important for the assessment of bio-based products, because the environmental impact of biomass production is not linearly dependent on the amount harvested. Furthermore, the results of the assessment need to be communicated in a meaningful way to the stakeholders who have different backgrounds and are often not familiar with LCA. The paper will discuss these challenges for the case of bio-based adipic acid production using the novel biorefinery concept, and will present results from the assessment and compare these to the case of fossil-based adipic acid production.
|
|
| 27. |
- Jiang, Wen, et al.
(författare)
-
Liquefaction of lignocellulosic materials and its applications in wood adhesives — A review
- 2018
-
Ingår i: Industrial crops and products (Print). - : Elsevier. - 0926-6690 .- 1872-633X. ; 124, s. 325-342
-
Tidskriftsartikel (refereegranskat)abstract
- Liquefaction, a useful method of turning whole biomass into liquids, provides advantages for energy andpolymers and finds applications in many sectors. This paper reviews the different liquefaction technologies andrecent advances in the development of sustainable wood adhesives. Current liquefaction technologies includehydrothermal liquefaction (HTL) and moderate acid-catalyzed liquefaction (MACL). HTL produces bio-oils asprimary products, and solid residues and gases as by-products. MACL depends on the solvent types used, whichare grouped to polyhydric alcohols and phenols. Bio-polyols from alcohol liquefaction, phenolated biomass fromphenol liquefaction and phenolic compounds rich-HTL bio-oils have been used in the production of liquefiedbiomass-based adhesives, which have shown competitive properties but face challenges for industrial uses. Yet, abetter understanding of reaction pathways and optimization of the liquefaction processes is needed.
|
|
| 28. |
- Salomon Johansen, Katja, 1969
(författare)
-
Oxidoreductases in biomass saccharification processes
- 2015
-
Ingår i: Oral presentation, 37th Symposium on biotechnology for fuels and chemicals, San Diego, US 2015.
-
Konferensbidrag (övrigt vetenskapligt/konstnärligt)abstract
- The inauguration of several commercial scale lignocellulosic ethanol factories within the past few months is a clear sign of the emergence of an industry. The development of an industry is likely to call for further studies of the fundamental principles governing the processes in order to facilitate further optimisation and thus competitive edge. Although impressive improvement in the efficiency of enzyme cocktails for lignocellulose deconstruction has been achieved already, the understanding of this process step is still incomplete. A recent development is the discovery of lytic polysaccharide monooxygenases which has opened a vide avenue for further studies of the mechanism by which plant cell wall are deconstructed in nature as well as in industrial settings. This is truly a new avenue within cellulase research which was in the past exclusively devoted to the study of hydrolases. Other oxidoreductases may also have a role to play. In nature, cellulytic LPMOs work in cooperation with another oxidoreductase, namely cellobiose dehydrogensase, but how the enzymes interact is inadequately described. In addition it has also been reported that laccase and peroxidase may have a positive effect on the saccharification efficiency but the mechanism behind is not understood in detail. The use of oxidoreductases in the production of lignocellulosic ethanol will be discussed in light of current scientific thinking and new insights.
|
|
| 29. |
- van Dijk, Marlous, 1990, et al.
(författare)
-
Bottlenecks in lignocellulosic ethanol production: xylose fermentation and cell propagation
- 2017
-
Ingår i: European biomass conference 2017, 25th edition, June 12-15; Stockholm, Sweden..
-
Konferensbidrag (övrigt vetenskapligt/konstnärligt)abstract
- A remaining challenge for the development of economically feasible 2nd generation bio-ethanol is low xylose consumption rate and inhibitor tolerance of the utilized Saccharomyces cerevisiae strains. Yeast starter cultures produced for ethanol production in simultaneous saccharification and co-fermentation (SSCF) processes have to meet high, seemingly conflicting requirements. A high biomass yield during propagation is required to produce the high cell concentrations required for the harsh conditions in the proceeding fermentation. Inhibitor tolerance is essential for producing a highly viable starter culture as well as favorable fermentation kinetics. Short-term adaptation of yeast cultures during propagation has been shown to have a positive effect on pentose conversion as well as inhibitor tolerance. Here we propose a model propagation strategy for evaluating physiology of yeast cultures during propagation. This model propagation strategy will be implemented in a study comparing physiology of yeast cultures with and without exposure to lignocellulosic inhibitors during propagation to assess what molecular mechanisms underlie the short-term adaptation response phenotype. For industry, a better control of yeast properties during propagation will result in an improved and consistent performance of yeast starter cultures for SSCF purposes.
|
|
| 30. |
- Wang, Ruifei, 1985, et al.
(författare)
-
Process optimization of multi-feed SSCF
- 2014
-
Ingår i: 10th European Symposium on Biochemical Engineering Sciences and 6th International Forum on Industrial Bioprocesses.
-
Konferensbidrag (övrigt vetenskapligt/konstnärligt)abstract
- Economical production of bio-ethanol from lignocellulosic materials requires an efficient and robust process which enables high-solid fermentation of pretreated lignocellulose to achieve high ethanol fermentation performance. In this work, we design and optimize a high-solid fed-batch simultaneous saccharification and co-fermentation (SSCF) process with a feed of substrate, enzyme and yeast cell for efficient production of ethanol from pretreated wheat straw in both lab and pilot scale. The yeast is prepared by pre-cultivation and adaptation in a semi-continuous cultivation in liquid hydrolysate medium in order to achieve high fermentation capacity. The feeding profiles in both pre-cultivation and SSCF steps are optimized based on a previously developed multi-feed SSCF model [1] in order to maintain high activities of both hydrolytic enzyme and yeast cell resulting in highest biomass yield during pre-cultivation and highest ethanol production efficiency during SSCF process. We also demonstrate scale up of fed-batch SSCF process in a 10 m3 pilot-scale bioreactor. The fed-batch SSCF with an optimized feed of substrate, cell and enzymes reaches high ethanol fermentation performance suggesting it to be a promising process for efficient bioconversion of lignocellulosic materials to ethanol.[1] Wang et al. Bioresour. Technol., 2014
|
|
| 31. |
- Skoog, Emma, 1983
(författare)
-
Biobased Adipic Acid - Challenges in Establishing a Cell Factory
- 2019
-
Doktorsavhandling (övrigt vetenskapligt/konstnärligt)abstract
- Growing concern regarding climate change calls for sustainable solutions to significantly reduce our dependency on non-renewable fossil-based raw materials. One potential solution is the development of biorefineries where biobased, renewable raw materials are converted into valuable products via enzymatic, chemical or microbial conversion. This work focuses on the microbial production of adipic acid, a precursor in the nylon industry, currently derived from fossil-based raw material. No known naturally occurring microorganism is able to produce adipic acid, and genetic engineering of a suitable host is therefore required. The aim of the work presented in this thesis was to engineer a microorganism for the production of adipic acid from glucose, more specifically, from glucose streams derived from lignocellulosic forest residues. Theoretical evaluation of metabolic pathways for adipic acid production revealed several obstacles, including redox imbalance and the discovery or engineering of enzymes to catalyze novel reactions. Mining of enzyme databases for alternative paths proved fruitful, and the number of biochemical reactions in the lysine pathway employing as yet unidentified enzymes was reduced from three to two, without affecting the thermodynamics of the pathway. A combined approach of in vitro and in silico analysis suggested potential enzyme engineering strategies for one of the reactions, for which there are as yet no identified enzymes, namely, the reduction of unsaturated α,β bonds of 6-aminohex-2-enoic acid and 2-hexenedioic acid. When defining a suitable host for microbial adipic acid production, tolerance to high concentrations of adipic acid (50-100 g L-1) is important to ensure an economically feasible process, preferably at low pH (below 5) to further reduce the overall process cost. Screening of bacteria, yeasts and a filamentous fungus grown in increasing concentrations of adipic acid (0-100 g L-1) and at different pH revealed Candida viswanathii to be a promising host to engineer for adipic acid production. A comparative study of C. viswanathii with Saccharomyces cerevisiae in controlled batch cultivations at increasing adipic acid concentrations (0-95 g L-1) and low pH (pH 4 and pH 5) revealed significant differences in their tolerance to adipic acid; C. viswanathii being able to grow, almost unaffected, under all the conditions investigated, whereas S. cerevisiae was unable to grow at 95 g L-1. Lipid analysis of their cell membranes revealed C. viswanathii to have a thicker and more compact cell membrane, which is probably less permeable to adipic acid.
|
|
| 32. |
- Hao, Nanjing, et al.
(författare)
-
Glyconanomaterials for biosensing applications
- 2016
-
Ingår i: Biosensors & bioelectronics. - : Elsevier. - 0956-5663 .- 1873-4235. ; 76:15, s. 113-130
-
Tidskriftsartikel (refereegranskat)abstract
- Nanomaterials constitute a class of structures that have unique physiochemical properties and are excellent scaffolds for presenting carbohydrates, important biomolecules that mediate a wide variety of important biological events. The fabrication of carbohydrate-presenting nanomaterials, glyconanomaterials, is of high interest and utility, combining the features of nanoscale objects with biomolecular recognition. The structures can also produce strong multivalent effects, where the nanomaterial scaffold greatly enhances the relatively weak affinities of single carbohydrate ligands to the corresponding receptors, and effectively amplifies the carbohydrate-mediated interactions. Glyconanomaterials are thus an appealing platform for biosensing applications. In this review, we discuss the chemistry for conjugation of carbohydrates to nanomaterials, summarize strategies, and tabulate examples of applying glyconanomaterials in in vitro and in vivo sensing applications of proteins, microbes, and cells. The limitations and future perspectives of these emerging glyconanomaterials sensing systems are furthermore discussed.
|
|
| 33. |
- Johansson, Nina, 1983
(författare)
-
A study of ethylene production via the 2-oxoglutarate dependent pathway in S. cerevisiae
- 2014
-
Doktorsavhandling (övrigt vetenskapligt/konstnärligt)abstract
- The detrimental effect of the petroleum industry on the environment combined with the threat of peak oil has driven the exploration for alternative strategies to produce traditional petrochemicals. Biotechnological production could be an alternative, using microorganisms to convert renewable feedstocks into desired products. A microbial based system for production of the traditional petrochemical ethylene has previously been developed through the expression of a bacterial version of the ethylene forming enzyme (EFE), which catalyzes the 2-oxoglutarate dependent ethylene pathway, in the yeast Saccharomyces cerevisiae. This work aims at deepening the understanding of how the EFE functions and investigate the functionality of the S. cerevisiae-EFE cell factory for ethylene production. To this end metabolic modeling, metabolic engineering as well as several cultivation studies have been performed. Alongside this the enzyme has been characterized through structural prediction and enzyme engineering, which has reviled both a structural entity necessary for ethylene forming functionality as well as a number of specific amino acid residues coupled to ethylene formation. Cultivation studies combined with metabolic engineering strategies have shown that balancing of arginine availability is important for optimal ethylene productivity. Further studies have also revealed that maintaining a high oxygenation level is a crucial cultivation factor for optimal ethylene productivity. This can be linked both to the reaction mechanism of the EFE, for which oxygen is a substrate, but also to an increased requirement of NADH re-oxidation when EFE is expressed. It was found that co-expression of heterologous oxidases could help relieve the redox stress and expression of the Aox1 of Histoplasma capsulatum was concluded to increase the ethylene yield with 28 %. To find further metabolic targets for increased ethylene productivity metabolic modeling was performed. The majority of the targets found were involved in supply of the EFE substrate 2-oxogltuarate, however none of the targets evaluated in vivo so far has given any increase in ethylene yields. Through this work important factors for optimal ethylene formation have been revealed, however it has also shown that more work is required before this system is a competitive alternative for ethylene production.
|
|
| 34. |
- Borgström, Celina, et al.
(författare)
-
Using phosphoglucose isomerase-deficient (pgi1Δ) Saccharomyces cerevisiae to map the impact of sugar phosphate levels on d-glucose and d-xylose sensing
- 2022
-
Ingår i: Microbial Cell Factories. - : Springer Science and Business Media LLC. - 1475-2859. ; 21:1
-
Tidskriftsartikel (refereegranskat)abstract
- Background: Despite decades of engineering efforts, recombinant Saccharomyces cerevisiae are still less efficient at converting d-xylose sugar to ethanol compared to the preferred sugar d-glucose. Using GFP-based biosensors reporting for the three main sugar sensing routes, we recently demonstrated that the sensing response to high concentrations of d-xylose is similar to the response seen on low concentrations of d-glucose. The formation of glycolytic intermediates was hypothesized to be a potential cause of this sensing response. In order to investigate this, glycolysis was disrupted via the deletion of the phosphoglucose isomerase gene (PGI1) while intracellular sugar phosphate levels were monitored using a targeted metabolomic approach. Furthermore, the sugar sensing of the PGI1 deletants was compared to the PGI1-wildtype strains in the presence of various types and combinations of sugars. Results: Metabolomic analysis revealed systemic changes in intracellular sugar phosphate levels after deletion of PGI1, with the expected accumulation of intermediates upstream of the Pgi1p reaction on d-glucose and downstream intermediates on d-xylose. Moreover, the analysis revealed a preferential formation of d-fructose-6-phosphate from d-xylose, as opposed to the accumulation of d-fructose-1,6-bisphosphate that is normally observed when PGI1 deletants are incubated on d-fructose. This may indicate a role of PFK27 in d-xylose sensing and utilization. Overall, the sensing response was different for the PGI1 deletants, and responses to sugars that enter the glycolysis upstream of Pgi1p (d-glucose and d-galactose) were more affected than the response to those entering downstream of the reaction (d-fructose and d-xylose). Furthermore, the simultaneous exposure to sugars that entered upstream and downstream of Pgi1p (d-glucose with d-fructose, or d-glucose with d-xylose) resulted in apparent synergetic activation and deactivation of the Snf3p/Rgt2p and cAMP/PKA pathways, respectively. Conclusions: Overall, the sensing assays indicated that the previously observed d-xylose response stems from the formation of downstream metabolic intermediates. Furthermore, our results indicate that the metabolic node around Pgi1p and the level of d-fructose-6-phosphate could represent attractive engineering targets for improved d-xylose utilization.
|
|
| 35. |
- Bajracharya, Suman, et al.
(författare)
-
Chapter 12 - Advances in gas fermentation processes
- 2022
-
Ingår i: Current Developments in Biotechnology and Bioengineering. - : Elsevier. - 9780323911672 ; , s. 321-351
-
Bokkapitel (övrigt vetenskapligt/konstnärligt)abstract
- Microbial metabolism enables the sustainable synthesis of fuels and chemicals from gaseous substrates (H2, CO, and CO2), thus drastically diminishing the carbon load in the atmosphere. Various value-added biochemicals and biofuels, such as acetate, methane, ethanol, butanol, butyrate, caproate, and bioplastics, have been produced during the conversion of syngas or H2/CO2, using a variety of microorganisms as biocatalysts. Gas fermentation processes using acetogenic and methanogenic organisms are being extensively investigated. This chapter provides an overview of microbial CO and CO2 conversion technology, with an emphasis on recent developments and integration with renewable electricity for the generation of H2 or other forms of electron donors. A discussion on technological challenges in gas fermentation addresses issues, such as poor mass transfer, low microbial biomass, and low productivity. It also presents possible solutions based on the latest advances in bioelectrochemical processes including microbial gas electrofermentation. Finally, the chapter includes a sustainability analysis of the process and includes a brief update on commercially established companies operating gas fermentation systems. Overall, an integrated approach combining gas fermentation and renewable electricity offers an opportunity for the development of CO and CO2- based biochemical and biofuel production at commercial scale.
|
|
| 36. |
- Brink, Daniel P., et al.
(författare)
-
D-xylose sensing in saccharomyces cerevisiae : Insights from D-glucose signaling and native D-xylose utilizers
- 2021
-
Ingår i: International Journal of Molecular Sciences. - : MDPI AG. - 1661-6596 .- 1422-0067. ; 22:22
-
Forskningsöversikt (refereegranskat)abstract
- Extension of the substrate range is among one of the metabolic engineering goals for microorganisms used in biotechnological processes because it enables the use of a wide range of raw materials as substrates. One of the most prominent examples is the engineering of baker’s yeast Saccharomyces cerevisiae for the utilization of D-xylose, a five-carbon sugar found in high abundance in lignocellulosic biomass and a key substrate to achieve good process economy in chemical production from renewable and non-edible plant feedstocks. Despite many excellent engineering strategies that have allowed recombinant S. cerevisiae to ferment D-xylose to ethanol at high yields, the consumption rate of D-xylose is still significantly lower than that of its preferred sugar D-glucose. In mixed D-glucose/D-xylose cultivations, D-xylose is only utilized after D-glucose depletion, which leads to prolonged process times and added costs. Due to this limitation, the response on D-xylose in the native sugar signaling pathways has emerged as a promising next-level engineering target. Here we review the current status of the knowledge of the response of S. cerevisiae signaling pathways to D-xylose. To do this, we first summarize the response of the native sensing and signaling pathways in S. cerevisiae to D-glucose (the preferred sugar of the yeast). Using the Dglucose case as a point of reference, we then proceed to discuss the known signaling response to Dxylose in S. cerevisiae and current attempts of improving the response by signaling engineering using native targets and synthetic (non-native) regulatory circuits.
|
|
| 37. |
- Aryapratama, Rio, et al.
(författare)
-
Prospective life cycle assessment of bio-based adipic acid production from forest residues
- 2017
-
Ingår i: Journal of Cleaner Production. - : Elsevier BV. - 0959-6526. ; 164, s. 434-443
-
Tidskriftsartikel (refereegranskat)abstract
- Abstract Environmental concerns related to the production of bulk chemicals are growing. Researchers and technology developers are currently looking into alternative production pathways for such chemicals by utilizing renewable resources, such as lignocellulosic feedstocks. Adipic acid is an example of such a bulk chemical, and its conventional fossil-based production emits significant amounts of N2O, a major greenhouse gas. In this study, a prospective life cycle assessment (LCA) of bio-based adipic acid production from forest residues at an early development stage, situated in Sweden, was conducted. Acid-catalyzed (using SO2) and alkaline (using NaBH4) pretreatment were employed and scenarios and sensitivity analyses were conducted. The potential environmental impacts of this technology under development were compared to those of conventional adipic acid production. The results show that bio-based adipic acid production has a lower impact on global warming, eutrophication and photochemical ozone creation compared to fossil-based production. In contrast, it has a higher impact on acidification. An increased efficiency of mitigating \{N2O\} emissions from the fossil-based production may alter this comparison. Producing bio-based adipic acid using the alkaline pretreatment has a higher environmental impact than producing it using acid-catalyzed pretreatment. Furthermore, if biomass is used to fulfil process energy demands, instead of fossil fuel, the environmental impact of the bio-based production decreases. It is therefore important to reduce the amount of NaBH4 used in the alkaline pretreatment or to lower the environmental impact of its production.
|
|
| 38. |
- Bonzom, Cyrielle, 1987, et al.
(författare)
-
Enzyme production and immobilization in mesoporous materials
- 2014
-
Konferensbidrag (övrigt vetenskapligt/konstnärligt)abstract
- Enzymes display high reactivity and selectivity under normal conditions, but may suffer from denaturation in industrial applications. A strategy to solve this limitation is to immobilize enzymes [1]. Mesoporous silica materials (MPS) have become a common choice as support to immobilized enzymes. MPS offer unique properties such as high enzyme loading and tunable pore size [2].Feruloyl esterase (FAE) is a subclass (EC. 3.1.1.73) of carboxylic ester hydrolases. They catalyze the hydrolysis of ester linkages in plant cell walls materials releasing ferulic acid and other hydroxycinnamic acids [3]. They are also examples of FAEs used for esterification and transesterification [4].From the genomes of Aspergillus glacus and Aspergillus oryzae, some putative FAE were identified. Among them, five were selected for further investigation in order to find a suitable enzyme for catalyzing the reaction of interest. The selected genes were quite distant in an evolutionary tree.The five putative FAEs were cloned into Pichia pastoris and produced by fed-batch fermentation. They were then purified either by IMAC columns or by ion-exchange chromatography. Their activity was assessed against a range of substrate to screen for FAE, tannase and other esterase activities. When the type of the respective enzyme activity was determined, some of them were further characterized. Five new enzymes were recombinantly produced and purified. Their activity type was determined and some of them were immobilized.Enzymes produced in sufficient quantities and having a good free activity were further investigated by immobilization. The selected support for immobilization was mesoporous silica particles (MPS). The conditions of immobilization were investigated and the activity once immobilized was tested and compared to the free one to gain insights on what happens during the immobilization of enzymes. Results were compared to those obtained with a commercially available FAE (E-FAERU, Megazyme).References.[1] Hudson S.; Cooney J.; Magner E., Angew. Chem. Int. Ed. 2008, 47, 8582-8594. [2] Carlsson N.; Gustafsson H.; Thörn C.; Olsson L.; Holmberg K.; Åkerman B. Advances in Colloid and Interface Science 2014, 204, 339-360.[3] Topakas E.; Vafiadi C.; Christakopoulos P. Process Biochemistry 2007, 42, 497-509.[4] Thörn C.; Gustafsson H.; Olsson L. Journal of molecular Catalysis B: Enzymatic 2011, 72, 57-64
|
|
| 39. |
- Karlsson, Emma, 1983, et al.
(författare)
-
METABOLIC ENGINEERING OF Saccharomyces cerevisiae FOR PRODUCTION OF ADIPIC ACID FROM RENEWABLE SOURCES
- 2014
-
Konferensbidrag (övrigt vetenskapligt/konstnärligt)abstract
- Adipic acid is a six carbon long dicarboxylic acid, considered to be the most important synthetic dicarboxylic acid annually produced, according to the International Energy Agency (IEA). The global production of adipic acid had in 2010 a volume of 2.8 million tonnes, for a total market price of 4.9 billion USD. The current production of adipic acid relies on non-renewable fossil raw materials, leading to emission of the greenhouse gases carbon dioxide and N2O. In addition, the production starts from benzene, whose use has several health related negative implications. This project aims to create a greener process for production of adipic acid developing a fermentation-based process using Swedish domestic renewable raw materials, such as forest residues and/or algae. These materials will be used to establish a biorefinery, wherein the fermentation process for the biosynthesis of adipic acid will represent the core process. Our current strategy is based on the generation of genetically modified strains of the yeast Saccharomyces cerevisiae, harbouring heterologous enzymatic activities allowing the conversion of lysine into adipic acid. This system is our first choice and will also work as proof-of-concept for bio-based production of adipic acid. Here we present the metabolic engineering strategy we are pursuing, based on two possible metabolic pathways for conversion of lysine into adipic acid. Preliminary results on the effect of adipic acid on S. cerevisiae physiology, lysine uptake, the expression of the heterologous genes of choice, and the conversion of lysine into adipic acid precursors are presented.
|
|
| 40. |
- Torén, Johan, et al.
(författare)
-
Food waste as a resource for bio-based chemicals and materials in Sweden
- 2019
-
Rapport (övrigt vetenskapligt/konstnärligt)abstract
- Waste, also food waste, abound. From an environmental point of view food waste should first and foremost be avoided. However, the waste that inevitably is produced along the food production chain should be utilized to the best of our ability. One option is to produce biobased chemicals and materials from the waste through biological processes. This study looks into what food waste resources are available for such production, industrial fermentation, in Sweden, from waste emanating in primary production all the way through to final consumption. In addition, drivers for waste generation, influencing institution and waste market characteristics are assessed.
|
|
| 41. |
- Ask, Magnus, 1983, et al.
(författare)
-
The influence of HMF and furfural on redox-balance and energy-state of xylose-utilizing Saccharomyces cerevisiae
- 2013
-
Ingår i: Biotechnology for Biofuels. - : Springer Science and Business Media LLC. - 1754-6834 .- 1754-6834. ; 6:22
-
Tidskriftsartikel (refereegranskat)abstract
- BackgroundPretreatment of biomass for lignocellulosic ethanol production generates compounds that can inhibit microbial metabolism. The furan aldehydes hydroxymethylfurfural (HMF) and furfural have received increasing attention recently. In the present study, the effects of HMF and furfural on redox metabolism, energy metabolism and gene expression were investigated in anaerobic chemostats where the inhibitors were added to the feed-medium.ResultsBy cultivating the xylose-utilizing Saccharomyces cerevisiae strain VTT C-10883 in the presence of HMF and furfural, it was found that the intracellular concentrations of the redox co-factors and the catabolic and anabolic reduction charges were significantly lower in the presence of furan aldehydes than in cultivations without inhibitors. The catabolic reduction charge decreased from 0.13(+/-0.005) to 0.08(+/-0.002) and the anabolic reduction charge decreased from 0.46(+/-0.11) to 0.27(+/-0.02) when HMF and furfural were present. The intracellular ATP concentration was lower when inhibitors were added, but resulted only in a modest decrease in the energy charge from 0.87(+/-0.002) to 0.85(+/-0.004) compared to the control. Transcriptome profiling followed by MIPS functional enrichment analysis of up-regulated genes revealed that the functional group "Cell rescue, defense and virulence" was over-represented when inhibitors were present compared to control cultivations. Among these, the ATP-binding efflux pumps PDR5 and YOR1 were identified as important for inhibitor efflux and possibly a reason for the lower intracellular ATP concentration in stressed cells. It was also found that genes involved in pseudohyphal growth were among the most up-regulated when inhibitors were present in the feed-medium suggesting nitrogen starvation. Genes involved in amino acid metabolism, glyoxylate cycle, electron transport and amino acid transport were enriched in the down-regulated gene set in response to HMF and furfural. It was hypothesized that the HMF and furfural-induced NADPH drainage could influence ammonia assimilation and thereby give rise to the nitrogen starvation response in the form of pseudohyphal growth and down-regulation of amino acid synthesis.ConclusionsThe redox metabolism was severely affected by HMF and furfural while the effects on energy metabolism were less evident, suggesting that engineering of the redox system represents a possible strategy to develop more robust strains for bioethanol production.
|
|
| 42. |
- Persson, Viktor C., et al.
(författare)
-
Impact of xylose epimerase on sugar assimilation and sensing in recombinant Saccharomyces cerevisiae carrying different xylose-utilization pathways
- 2023
-
Ingår i: Biotechnology for Biofuels and Bioproducts. - 2731-3654. ; 16:1
-
Tidskriftsartikel (refereegranskat)abstract
- BackgroundOver the last decades, many strategies to procure and improve xylose consumption in Saccharomyces cerevisiae have been reported. This includes the introduction of efficient xylose-assimilating enzymes, the improvement of xylose transport, or the alteration of the sugar signaling response. However, different strain backgrounds are often used, making it difficult to determine if the findings are transferrable both to other xylose-consuming strains and to other xylose-assimilation pathways. For example, the influence of anomerization rates between α- and β-xylopyranose in pathway optimization and sugar sensing is relatively unexplored.ResultsIn this study, we tested the effect of expressing a xylose epimerase in S. cerevisiae strains carrying different xylose-consuming routes. First, XIs originating from three different species in isogenic S. cerevisiae strains were tested and the XI from Lachnoclostridium phytofermentans was found to give the best performance. The benefit of increasing the anomerization rate of xylose by adding a xylose epimerase to the XI strains was confirmed, as higher biomass formation and faster xylose consumption were obtained. However, the impact of xylose epimerase was XI-dependent, indicating that anomer preference may differ from enzyme to enzyme. The addition of the xylose epimerase in xylose reductase/xylitol dehydrogenase (XR/XDH)-carrying strains gave no improvement in xylose assimilation, suggesting that the XR from Spathaspora passalidarum had no anomer preference, in contrast to other reported XRs. The reduction in accumulated xylitol that was observed when the xylose epimerase was added may be associated with the upregulation of genes encoding endogenous aldose reductases which could be affected by the anomerization rate. Finally, xylose epimerase addition did not affect the sugar signaling, whereas the type of xylose pathway (XI vs. XR/XDH) did.ConclusionsAlthough xylose anomer specificity is often overlooked, the addition of xylose epimerase should be considered as a key engineering step, especially when using the best-performing XI enzyme from L. phytofermentans. Additional research into the binding mechanism of xylose is needed to elucidate the enzyme-specific effect and decrease in xylitol accumulation. Finally, the differences in sugar signaling responses between XI and XR/XDH strains indicate that either the redox balance or the growth rate impacts the SNF1/Mig1p sensing pathway.
|
|
| 43. |
- Shin, Jae Ho, 1987
(författare)
-
Engineering synthetic pathways for adipic acid biosynthesis
- 2021
-
Doktorsavhandling (övrigt vetenskapligt/konstnärligt)abstract
- Utilization of petroleum in consumer product manufacturing is causing irreversible environmental damage. Its impact on land, sea, and air calls for the development of more sustainable technologies based on the use of renewable materials such as lignocellulosic biomass and its conversion into platform chemicals. Engineering microorganisms to produce chemicals is an important undertaking to address such issues and bio-based production of adipic acid especially has gained recent attention. In the present thesis I assess the in vivo and in silico action of enzymes involved in microbial production of adipic acid from simple sugar molecules. The aim of this work was to comprehensively map out the metabolic pathways leading to adipic acid biosynthesis and to investigate the enzymatic components of the L-lysine pathway, the reverse β-oxidation pathway, and cis,cis -muconic acid reduction. Investigation of theoretical and in silico aspects in the deamination step in the L-lysine pathway revealed deamination of L-lysine was determined to be chemically difficult to occur. Removal of the β-amino group from β-D-lysine was deemed more feasible than the α-amino group from L-lysine, and an alternative route via β-D-lysine deamination was suggested. Homology modeling and molecular docking studies shed light on the substrate binding mechanisms of enzymes responsible for the reduction of the intermediates in the L-lysine pathway. Potential mechanism and feasibility of α,β-reduction were explained in terms of substrate interaction in the enzyme-binding pockets. Corynebacterium glutamicum was chosen as the host chassis for achieving adipic acid synthesis via reverse β-oxidation. Stepwise construction of a five-step synthetic pathway demonstrated functionality of each step in C. glutamicum. Biosynthesized and secreted 3-hydroxyadipate was detected in the cultivation broth using GC/MS. Weak trans-2-hexenedioic acid and adipic acid signals was observed using LC/MS after concentrating the cultivation broth. Dehydration of 3-hydroxyadipyl-CoA was identified as a potential bottleneck hindering this pathway. While implementing the reverse β-oxidation pathway, a new pathway involving cis,cis -muconic acid and 3-oxoadipic acid was observed and experimented on. The modified strategy for bio-conversion of benzoic acid to cis,cis -muconic acid was successful and molecular docking studies were carried out to better understand how oxidoreductases might reduce cis,cis -muconic acid. Taking multiple approaches to generate adipic acid revealed different challenges in each pathway. One approach led to biosynthesis of adipic acid. Further investigation will allow multiple options for bio-based adipic acid production for better sustainability.
|
|
| 44. |
- Teixeira, Paulo, 1990
(författare)
-
Engineering Lipid Metabolism for Production of Oleochemicals in Saccharomyces cerevisiae
- 2018
-
Doktorsavhandling (övrigt vetenskapligt/konstnärligt)abstract
- Oleochemicals are chemicals usually derived from plant oils or animal fat. Large use of plant oil derivatives as replacements for petroleum-derived chemicals brings sustainability issues from extensive cultivation of oil plants in restricted regions. This project studied and developed the baker’s yeast Saccharomyces cerevisiae as a platform for sustainable production of oleochemical precursors. The first part of this work studied the dynamics of free fatty acids (FFAs) production. First, an alternative fatty acid synthesis system based on the reverse β-oxidation pathway was evaluated for its in vivo function but concluding that it was not an efficient route for fatty acid synthesis. The subsequent studies were based on high level production of FFA and secretion to the extracellular medium through removal of acyl-CoA synthase activity by deleting the FAA1-4 genes. This phenotype was coupled to a pathway that converts FFA to fatty alcohols, which allowed the observation that while FFA are more efficiently converted to fatty alcohols during growth on glucose, the production of FFA is highly increased during growth on ethanol. Fine-tuning of FAA1 expression resulted in improved production of fatty alcohols without FFA secretion in this strain. Following up, the pathways leading to FFA formation in a Δfaa1 Δfaa4 background were studied through construction of a strain with a constrained lipid metabolism network. It was observed that upon removing storage lipid formation, phospholipid synthesis had a strong correlation with FFA production and FFA formation was mostly derived from phospholipid hydrolysis. On the second part of this work, S. cerevisiae was engineered for the highest TAG production levels reported so far. This relied on overexpressing genes involved in malonyl-CoA supply and TAG synthesis from acyl-CoA, and removing genes involved in TAG hydrolysis, β-oxidation and glycerol-3-phosphate usage. On a second approach, TAG accumulation properties were further improved in these strains through enhancing lipid droplet assembly processes. This was achieved through expression of perilipins and FIT proteins and through stimulation of ER stress mechanisms. In conclusion, lipid metabolism is an important part of cell homeostasis and engineering this system requires overcoming its tight regulation networks and mastering the processes involved in the physical structural organization of the system. Here this was highlighted using both knowledge-driven studies and engineering approaches, leading to important advancements in the field.
|
|
| 45. |
- Wang, Zhao, 1989-
(författare)
-
Recalcitrance of wood to biochemical conversion : feedstock properties, pretreatment, saccharification, and fermentability
- 2018
-
Doktorsavhandling (övrigt vetenskapligt/konstnärligt)abstract
- Lignocellulose is an inexpensive and abundant renewable resource that can be used to produce advanced biofuels, green chemicals, and other bio-based products. Pretreatment and efficient enzymatic saccharification are essential features of bioconversion of lignocellulosic biomass. The aims of the research were to achieve a better understanding of the recalcitrance of woody biomass to bioconversion, to explore different pretreatment techniques that can be used to decrease the recalcitrance of the biomass and improve the digestibility of the cellulose, and to investigate by-products of acid pretreatment that cause enzymes and microorganisms to work less efficiently.The recalcitrance of wood from aspen, birch, and spruce was investigated before and after acid pretreatment. Before pretreatment, birch exhibited the highest recalcitrance, which was attributed to structural factors. After pretreatment, spruce showed the highest recalcitrance, which was attributed to chemical factors, such as high lignin content. Deacetylation of hybrid aspen in planta by a CE5 acetyl xylan esterase decreased the recalcitrance, and the glucose yield of enzymatic saccharification of non-pretreated wood increased with 27%.Pretreatment options based on ionic liquids and steam explosion were further explored. The effects of the anionic constituents of a series of imidazolium-based ionic liquids on pretreatment of aspen and spruce were investigated. [HSO4]− was efficient only for aspen, which was attributed to acid degradation of xylan. [MeCO2]− was efficient for both aspen and spruce, which was attributed to its capability to create a disordered cell wall structure rather than to removal of lignin and hemicellulose. A comparison was made between using sulfuric acid and sulfur dioxide for pretreatment of spruce. Although sulfur dioxide resulted in a pretreatment liquid that was more inhibitory to both enzymes and yeast, it was still superior to pretreatment with sulfuric acid, a phenomenon that was attributed to the particle size of the pretreated material.In a comparison of microbial inhibitors in pretreatment liquids from steam explosion of spruce, formaldehyde was found to be the most important inhibitor of yeast. Enzyme inhibition by catalytically non-productive adsorption to lignins and pseudo-lignin was investigated using quantitative proteomics. The results indicate that protein adsorption to pseudo-lignin can be as extensive as adsorption to real lignin.
|
|
| 46. |
- Li, Xue-Yuan, et al.
(författare)
-
Combination of modern plant breeding and enzyme technology to obtain highly enriched erucic acid from Crambe oil
- 2016
-
Ingår i: Sustainable Chemical Processes. - : Springer Science and Business Media LLC. - 2043-7129. ; 4
-
Tidskriftsartikel (refereegranskat)abstract
- Background Fatty acids from vegetable oils are useful building blocks for industrial materials. The purpose of this work was to prepare erucic acid with high purity from a vegetable oil. High purity erucic acid is used for the production of erucamide with applications in plastics manufacturing. A newly developed transgenic Crambe line produces seed oil with 68% erucic acid compared to 53% in the wild type oil. Results Further enrichment of erucic acid from Crambe (wild type and transgenic) oil was achieved by selective enzymatic hydrolysis. UsingCandida rugosalipase as catalyst, other fatty acids were preferentially hydrolysed from the triacylglycerols and erucic acid was enriched in the acylglycerol fraction. The highest content of erucic acid achieved in that fraction was 95%. Conclusions The combination of modern plant breeding and enzyme technology is a promising approach for preparation of fatty acids of high purity.
|
|
| 47. |
- Abitbol, Tiffany, et al.
(författare)
-
Isolation of Mixed Compositions of Cellulose Nanocrystals, Microcrystalline Cellulose, and Lignin Nanoparticles from Wood Pulps
- 2023
-
Ingår i: ACS Omega. - : American Chemical Society (ACS). - 2470-1343. ; 8:24, s. 21474-21484
-
Tidskriftsartikel (refereegranskat)abstract
- From a circular economyperspective, one-pot strategies for theisolation of cellulose nanomaterials at a high yield and with multifunctionalproperties are attractive. Here, the effects of lignin content (bleachedvs unbleached softwood kraft pulp) and sulfuric acid concentrationon the properties of crystalline lignocellulose isolates and theirfilms are explored. Hydrolysis at 58 wt % sulfuric acid resulted inboth cellulose nanocrystals (CNCs) and microcrystalline celluloseat a relatively high yield (>55%), whereas hydrolysis at 64 wt% gaveCNCs at a lower yield (<20%). CNCs from 58 wt % hydrolysis weremore polydisperse and had a higher average aspect ratio (1.5-2x),a lower surface charge (2x), and a higher shear viscosity (100-1000x).Hydrolysis of unbleached pulp additionally yielded spherical nanoparticles(NPs) that were <50 nm in diameter and identified as lignin bynanoscale Fourier transform infrared spectroscopy and IR imaging.Chiral nematic self-organization was observed in films from CNCs isolatedat 64 wt % but not from the more heterogeneous CNC qualities producedat 58 wt %. All films degraded to some extent under simulated sunlighttrials, but these effects were less pronounced in lignin-NP-containingfilms, suggesting a protective feature, but the hemicellulose contentand CNC crystallinity may be implicated as well. Finally, heterogeneousCNC compositions obtained at a high yield and with improved resourceefficiency are suggested for specific nanocellulose uses, for instance,as thickeners or reinforcing fillers, representing a step toward thedevelopment of application-tailored CNC grades.
|
|
| 48. |
- Honarvar, Hadis, et al.
(författare)
-
Position for site-specific attachment of a DOTA chelator to synthetic affibody molecules has a different influence on the targeting properties of 68Ga-Compared to 111in-labeled conjugates
- 2014
-
Ingår i: Molecular Imaging. - : SAGE Publications. - 1535-3508 .- 1536-0121. ; 13:10
-
Tidskriftsartikel (refereegranskat)abstract
- Affibody molecules, small (7 kDa) scaffold proteins, are a promising class of probes for radionuclide molecular imaging. Radiolabeling of Affibody molecules with the positron-emitting nuclide 68Ga would permit the use of positron emission tomography (PET), providing better resolution, sensitivity, and quantification accuracy than single-photon emission computed tomography (SPECT). The synthetic anti-HER2 ZHER2:S1 Affibody molecule was conjugated with DOTA at the N-terminus, in the middle of helix 3, or at the Cterminus. The biodistribution of 68Ga-and 111In-labeled Affibody molecules was directly compared in NMRI nu/nu mice bearing SKOV3 xenografts. The position of the chelator strongly influenced the biodistribution of the tracers, and the influence was more pronounced for 68Ga-labeled Affibody molecules than for the 111In-labeled counterparts. The best 68Ga-labeled variant was 68Ga-[DOTA-A1]-ZHER2:S1, which provided a tumor uptake of 13 ± 1 %ID/g and a tumor to blood ratio of 39 ± 12 at 2 hours after injection. 111In-[DOTA-A1]-ZHER2:S1 and 111In-[DOTA-K58]-ZHER2:S1 were equally good at this time point, providing a tumor uptake of 15 to 16 %ID/g and a tumor to blood ratio in the range of 60 to 80. In conclusion, the selection of the best position for a chelator in Affibody molecules can be used for optimization of their imaging properties. This may be important for the development of Affibody-based and other protein-based imaging probes.
|
|
| 49. |
- Bonzom, Cyrielle, 1987, et al.
(författare)
-
Feruloyl esterase immobilization in mesoporous silica: hydrolysis and transesterifications reactions.
- 2015
-
Konferensbidrag (övrigt vetenskapligt/konstnärligt)abstract
- Mesoporous silica materials (MPS) are an interesting choice as support to immobilize enzymes because MPS offer unique properties such as high enzyme loading and tunable pore size. They also provide the enzyme with a sheltered environment therefore reducing the risks of denaturation in industrial applications.Immobilization parameters such as pH, buffer and pore size of the material were investigated. Among them, the chemical composition of the buffer as well as its pH proved to be critical resulting in enzyme loadings varying from nearly zero up to 0.025 mgenzyme.mgMPS-1.Selectivity of the enzyme, a feruloyl esterase (FAE), was investigated by quantifying the molar ratio between the transesterification and hydrolysis products, namely butyl ferulate (BFA) and ferulic acid (FA). The reaction of interest was transesterification therefore hydrolysis was an unwanted side-reaction. The immobilization pH and the water content of the reaction were the most influent parameters inducing variation up to 4-fold of the BFA/FA molar ratio.Optimal reaction conditions and kinetic parameters of the free and immobilized enzyme were determined for both hydrolysis and transesterification to determine in which conditions transesterification is prevailing. While optimal pHs were similar for all studied, temperature optimums varied from 25 to 50°C. Interestingly the Km of the FAE was not affected upon immobilization, but the kcat was decreased 10-fold resulting in a lower catalytic efficiency. Km was 100-fold higher for transesterification than for hydrolysis whereas kcat was 100-fold lower; this resulted in a drastic reduction of the catalytic efficiency of the FAE.Stability of the enzyme was evaluated using the hydrolysis reaction. No significant improvement could be observed for the immobilized enzyme. Reusability of the immobilized biocatalyst was determined during 10-cycles of 48h. A decrease in activity was observed during the course of the experiment. In addition a decrease in the BFA/FA molar ratio indicating a shift in enzyme specificity happened.
|
|
| 50. |
- Shin, Jae Ho, 1987, et al.
(författare)
-
Synthetic pathway engineering in Corynebacterium glutamicum for production of adipic acid
- 2020
-
Konferensbidrag (övrigt vetenskapligt/konstnärligt)abstract
- We are interested in production of adipic acid from renewable sources using a gram-positive bacterium, Corynebacterium glutamicum ATCC 13032, as a target for metabolic engineering. We aim to construct a synthetic pathway that would allow biosynthesis of adipic acid and to implement it into the host chassis for utilizing simple sugar, glucose, as the starting raw material. The chosen pathway stems off from intermediates from the central metabolism and requires 5 synthetic biochemical steps before reaching adipic acid. The pathway is equipped with a promiscuous enzyme to allow leakage at each metabolic step and byproduct formation in order to monitor the efficiency of each step of the pathway. In order to ensure translation, each gene introduced was codon-optimized to C. glutamicum. Introducing the synthetic genes one by one into C. glutamicum as well as flask-level cultivation of engineered strains in a semi-defined medium allowed detection of each byproduct of the pathway leading up to adipic acid by GC/MS based methods. Further, the codon-optimized version of the 5 synthetic genes were constructed in 2 separate operons each with an inducible promoter. Finally, we analyzed the translational efficiency of the genes and modified the constructs for a better operon expression. We implement additional sample preparation methods for isolating and concentrating adipic acid content for better analysis. The results shown here will be used to further develop and complete biosynthesis of adipic acid from a C. glutamicum chassis.
|
|
