| 1. |
- Bryne, Lars Elof, 1969-
(författare)
-
Time dependent material properties of shotcrete for hard rock tunnelling
- 2014
-
Doktorsavhandling (övrigt vetenskapligt/konstnärligt)abstract
- In this thesis different mechanical properties for shotcrete (sprayed concrete) such as compression strength, bond strength, bending tensile strength, elastic modulus, free and restrained shrinkage as a function of its age was investigated. One of the main issues was to investigate the difference between ordinary cast concrete and shotcrete. Reliable material data for young and hardening shotcrete is scarce which in the past have made such comparisons difficult. Also, less accurate data representative for cast concrete has often been used in numerical modelling and design analyses. The focus of the project has particularly been on the properties bond strength and restrained shrinkage for which two new testing methods has been developed and evaluated. Microstructural studies have also been performed as a complement to the bond strength testing.The bond to rock is one of the most important properties for shotcrete used as rock reinforcement. During the very first time after spraying the physical properties and the bond to the rock depend on the set accelerator and the micro structure that is formed. The investigation of early age bond strength of shotcrete is of great importance both from a production perspective and a safety perspective. The newly developed method was tested and evaluated and proved that it can be used for bond strength testing already from a couple of hours after shotcreting. The bond, or adhesion, depends on several factors such as texture of the rock, the type of accelerator, application technique, etc. In this work the development of the microstructure in the interfacial transition zone (ITZ) and strength of the bond was investigated. The results show that the bond strength is related to the hydration process, i.e. the strength gain of the shotcrete. The early development of the ITZ was here studied using a scanning electron microscope (SEM) making it possible to observe changes over time, before and after proper cement hydration.Restrained shrinkage cracking of shotcrete, especially in the case of shotcrete sprayed on soft drains that are parts of a tunnel lining not continuously bonded to the rock, can be detrimental for the sustainability of an infrastructure tunnel system. Maintenance and repair costs can be high over time. It is shown that the developed test method realistically captures the behaviour of shotcrete drains on hard rock in situ. The method can be used in the evaluation of different technical solutions for avoiding or minimizing shrinkage cracks in shotcreted soft drains. It can also be used to assess the performance of shotcrete fully bonded to a rock surface, with respect to the ability to prevent cracking or to distribute possible shrinkage damage into several fine cracks instead of one wide.
|
|
| 2. |
- Ahmed, Lamis
(författare)
-
Models for analysis of shotcrete on rock exposed to blasting
- 2012
-
Licentiatavhandling (övrigt vetenskapligt/konstnärligt)abstract
- In underground construction and tunnelling, the strive for a more time-efficient construction process naturally focuses on the possibilities of reducing the times of waiting between stages of construction. The ability to project shotcrete (sprayed concrete) on a rock surface at an early stage after blasting is vital to the safety during construction and function of e.g. a tunnel. A complication arises when the need for further blasting affects the hardening of newly applied shotcrete. If concrete, cast or sprayed, is exposed to vibrations at an early age while still in the process of hardening, damage that threatens the function of the hard concrete may occur. There is little, or no, established knowledge on the subject and there are no guidelines for practical use. It is concluded from previous investigations that shotcrete can withstand high particle velocity vibrations without being seriously damaged. Shotcrete without reinforcement can survive vibration levels as high as 0.5−1 m/s while sections with loss of bond and ejected rock will occur for vibration velocities higher than 1 m/s. The performance of young and hardened shotcrete exposed to high magnitudes of vibration is here investigated to identify safe distances and shotcrete ages for underground and tunnelling construction, using numerical analyses and comparison with measurements and observations. The work focuses on finding correlations between numerical results, measurement results and observations obtained during tunnelling. The outcome will be guidelines for practical use. The project involves development of sophisticated dynamic finite element models for which the collected information and data will be used as input, accomplished by using the finite element program Abaqus. The models were evaluated and refined through comparisons between calculated and measured data. First, existing simple engineering models were compared and evaluated through calculations and comparisons with existing data. The first model tested is a structural dynamic model that consists of masses and spring elements. The second is a model built up with finite beam elements interconnected with springs. The third is a one-dimensional elastic stress wave model. The stress response in the shotcrete closest to the rock when exposed to P-waves striking perpendicularly to the shotcrete-rock interface was simulated. Results from a non-destructive laboratory experiment were also used to provide test data for the models. The experiment studied P-wave propagation along a concrete bar, with properties similar to rock. Cement based mortar with properties that resembles shotcrete was applied on one end of the bar with a hammer impacting the other. The shape of the stress waves travelling towards the shotcrete was registered using accelerometers positioned along the bar. Due to the inhomogeneous nature of the rock, the stress waves from the blasting attenuate on the way from the point of explosion towards the shotcrete on the rock surface. Material damping for the rock mass is therefore accounted for, estimated from previous in-situ measurements. The vibration resistance of the shotcrete-rock support system depends on the material properties of the shotcrete and here were age-dependent properties varied to investigate the behaviour of young shotcrete subjected to blast loading. The numerical simulations require insertion of realistic material data for shotcrete and rock, such as density and modulus of elasticity. The calculated results were in good correspondence with observations and measurements in-situ, and with the previous numerical modelling results. Compared to the engineering models, using a sophisticated finite element program facilitate modelling of more complex geometries and also provide more detailed results. It was demonstrated that wave propagation through rock towards shotcrete can be modelled using two dimensional elastic finite elements in a dynamic analysis. The models must include the properties of the rock and the accuracy of the material parameters used will greatly affect the results. It will be possible to describe the propagation of the waves through the rock mass, from the centre of the explosion to the reflection at the shotcrete-rock interface. It is acceptable to use elastic material formulations until the material strengths are exceeded, i.e. until the strains are outside the elastic range, which thus indicates material failure. The higher complexity of this type of model, compared to the engineering models, will make it possible to model more sophisticated geometries. Examples of preliminary recommendations for practical use are given and it is demonstrated how the developed models and suggested analytical technique can be used to obtain further detailed limit values.
|
|
| 3. |
- Ansell, Anders, et al.
(författare)
-
Concrete Structures
- 2012
-
Rapport (övrigt vetenskapligt/konstnärligt)
|
|
| 4. |
- Rydell, Cecilia, 1978-
(författare)
-
Seismic high-frequency content loads on structures and components within nuclear facilities
- 2014
-
Licentiatavhandling (övrigt vetenskapligt/konstnärligt)abstract
- Sweden is generally considered to be a low seismicity area, but for structures within nuclear power facilities, the safety level demand with respect to seismic events are high and thus, these structures are required to be earthquake-resistant. The seismic hazard is here primarily considered to be associated with near-field earthquakes. The nuclear power plants are further founded on hard rock and the expected ground motions are dominated by high frequencies. The design earthquake considered for the nuclear facilities has an annual probability of 10-5 events, that is, the probability of occurrence is once per 100 000 years. The focus of the study is the seismic response of large concrete structures for the nuclear power industry, with regard not only to the structure itself but also to non-structural components attached to the primary structure, and with emphasis on Swedish conditions. The aim of this licentiate thesis is to summarize and demonstrate some important aspects when the seismic load is dominated by high frequencies. Additionally, an overview of laws, regulations, codes, standards, and guidelines important for seismic analysis and design of nuclear power structures is provided.The thesis includes two case studies investigating the effect of seismic high-frequency content loads. The first study investigates the influence of gaps in the piping supports on the response of a steel piping system subjected to a seismic load dominated by high amplitudes at high frequencies. The gaps are found in the joints of the strut supports or are gaps between the rigid box supports and the pipe. The piping system is assessed to be susceptible to high-frequency loads and is located within the reactor containment building of a nuclear power plant. The stress response of the pipe and the acceleration response of the valves are evaluated. The second study investigates the effect of fluid-structure interaction (FSI) on the response of an elevated rectangular water-containing concrete pool subjected to a seismic load with dominating low and high frequencies, respectively. The pool is located within the reactor containment building of a boiling water reactor at a nuclear power plant. The hydrodynamic pressure distribution is evaluated together with the stress distribution in the walls of the tank.From the two case studies, it is evident that the response due to a seismic load dominated by high frequencies and low frequencies, respectively, is different. Although the seismic high-frequency load may be considered non-damaging for the structure, the effect may not be negligible for non-structural components attached to the primary structure. Including geometrical non-linear effects such as gaps may however reduce the response. It was shown that the stress response for most of the pipe elements in the first case study was reduced due to the gaps. It may also be that the inclusion of fluid-structure interaction effects changes the dynamic properties of a structural system so that it responds significantly in the high frequency range, thus making it more vulnerable to seismic loads dominated by high frequencies. In the second case study, it was shown that even for a seismic load with small amplitudes and short duration, but with dominating high-frequency content, as the Swedish 10-5 design earthquake, the increase of the dynamic response as fluid-structure interaction is accounted for is significant.
|
|
