| 1. |
- Abelev, Betty, et al.
(författare)
-
Long-range angular correlations on the near and away side in p-Pb collisions at root S-NN=5.02 TeV
- 2013
-
Ingår i: Physics Letters. Section B: Nuclear, Elementary Particle and High-Energy Physics. - : Elsevier BV. - 0370-2693. ; 719:1-3, s. 29-41
-
Tidskriftsartikel (refereegranskat)abstract
- Angular correlations between charged trigger and associated particles are measured by the ALICE detector in p-Pb collisions at a nucleon-nucleon centre-of-mass energy of 5.02 TeV for transverse momentum ranges within 0.5 < P-T,P-assoc < P-T,P-trig < 4 GeV/c. The correlations are measured over two units of pseudorapidity and full azimuthal angle in different intervals of event multiplicity, and expressed as associated yield per trigger particle. Two long-range ridge-like structures, one on the near side and one on the away side, are observed when the per-trigger yield obtained in low-multiplicity events is subtracted from the one in high-multiplicity events. The excess on the near-side is qualitatively similar to that recently reported by the CMS Collaboration, while the excess on the away-side is reported for the first time. The two-ridge structure projected onto azimuthal angle is quantified with the second and third Fourier coefficients as well as by near-side and away-side yields and widths. The yields on the near side and on the away side are equal within the uncertainties for all studied event multiplicity and p(T) bins, and the widths show no significant evolution with event multiplicity or p(T). These findings suggest that the near-side ridge is accompanied by an essentially identical away-side ridge. (c) 2013 CERN. Published by Elsevier B.V. All rights reserved.
|
|
| 2. |
- Abelev, Betty, et al.
(författare)
-
Measurement of prompt J/psi and beauty hadron production cross sections at mid-rapidity in pp collisions at root s=7 TeV
- 2012
-
Ingår i: Journal of High Energy Physics. - 1029-8479. ; :11
-
Tidskriftsartikel (refereegranskat)abstract
- The ALICE experiment at the LHC has studied J/psi production at mid-rapidity in pp collisions at root s = 7 TeV through its electron pair decay on a data sample corresponding to an integrated luminosity L-int = 5.6 nb(-1). The fraction of J/psi from the decay of long-lived beauty hadrons was determined for J/psi candidates with transverse momentum p(t) > 1,3 GeV/c and rapidity vertical bar y vertical bar < 0.9. The cross section for prompt J/psi mesons, i.e. directly produced J/psi and prompt decays of heavier charmonium states such as the psi(2S) and chi(c) resonances, is sigma(prompt J/psi) (p(t) > 1.3 GeV/c, vertical bar y vertical bar < 0.9) = 8.3 +/- 0.8(stat.) +/- 1.1 (syst.)(-1.4)(+1.5) (syst. pol.) mu b. The cross section for the production of b-hadrons decaying to J/psi with p(t) > 1.3 GeV/c and vertical bar y vertical bar < 0.9 is a sigma(J/psi <- hB) (p(t) > 1.3 GeV/c, vertical bar y vertical bar < 0.9) = 1.46 +/- 0.38 (stat.)(-0.32)(+0.26) (syst.) mu b. The results are compared to QCD model predictions. The shape of the p(t) and y distributions of b-quarks predicted by perturbative QCD model calculations are used to extrapolate the measured cross section to derive the b (b) over bar pair total cross section and d sigma/dy at mid-rapidity.
|
|
| 3. |
- Abelev, Betty, et al.
(författare)
-
Underlying Event measurements in pp collisions at root s=0.9 and 7 TeV with the ALICE experiment at the LHC
- 2012
-
Ingår i: Journal of High Energy Physics. - 1029-8479. ; :7
-
Tidskriftsartikel (refereegranskat)abstract
- We present measurements of Underlying Event observables in pp collisions at root s = 0 : 9 and 7 TeV. The analysis is performed as a function of the highest charged-particle transverse momentum p(T),L-T in the event. Different regions are defined with respect to the azimuthal direction of the leading (highest transverse momentum) track: Toward, Transverse and Away. The Toward and Away regions collect the fragmentation products of the hardest partonic interaction. The Transverse region is expected to be most sensitive to the Underlying Event activity. The study is performed with charged particles above three different p(T) thresholds: 0.15, 0.5 and 1.0 GeV/c. In the Transverse region we observe an increase in the multiplicity of a factor 2-3 between the lower and higher collision energies, depending on the track p(T) threshold considered. Data are compared to PYTHIA 6.4, PYTHIA 8.1 and PHOJET. On average, all models considered underestimate the multiplicity and summed p(T) in the Transverse region by about 10-30%.
|
|
| 4. |
- Altimira, Mireia, 1981-, et al.
(författare)
-
Disintegration regime of industrial fan-spray atomizers through CFD simulations
- 2011
-
Ingår i: ILASS – Europe 2011, 24th European Conference on Liquid Atomization and Spray Systems, Estoril, Portugal, September 2011.
-
Konferensbidrag (refereegranskat)abstract
- Among all the literature devoted to the investigation of sprays, very few works deal with the influence of the nozzle’s geometry on the characteristics of the spray produced, even though it has been proved to play a crucial role in certain operating regimes. The present paper presents criteria for the determination of the dominant disintegration regime in industrial fan-spray atomizers through CFD simulations accounting for the atomizer’s geometry.
|
|
| 5. |
- Altimira, Mireia, 1981-, et al.
(författare)
-
Linear spatial instability of viscous flow of a liquid sheet through gas
- 2010
-
Ingår i: Physics of fluids. - : American Institute of Physics (AIP). - 1070-6631 .- 1089-7666. ; 22:7
-
Tidskriftsartikel (refereegranskat)abstract
- The present paper focuses on the linear spatial instability of a viscous two-dimensional liquid sheet bounded by two identical viscous gas streams. The Orr–Sommerfeld differential equations and the boundary conditions of the flow configuration are numerically solved using Chebyshev series expansions and the collocation method. The strong dependence of the instability parameters on the velocity profiles is proven by using both quadratic and error functions to define the base flow in the liquid sheet and the gas shear layer. The sensitivity of the spatial instability growth rate to changes in the dimensionless parameters of the problem is assessed. Regarding the liquid sheet Reynolds number, it has been observed that, when this parameter increases, both the most unstable growth rate and the corresponding wavenumber decrease, whereas the cutoff wavenumber increases. The results of this analysis are compared with temporal theory through Gaster transformation. The effects liquid and gas viscosity have on instability are studied by comparing the instability curves given by the presented model with those from an inviscid liquid sheet and a viscous liquid sheet in an inviscid gaseous medium. The model presented in this paper features a variation in the cutoff wavenumber with all the governing parameters of the problem, whereas that provided by cases that account for an inviscid surrounding gas depends only on the liquid sheet Weber number and the ratio of gas to liquid densities. Results provided by the presented model have been experimentally validated and show that quadratic profiles have a greater capacity to predict the disturbance wavelength.
|
|
| 6. |
- Larraona, Gorka S., et al.
(författare)
-
Computational parametric study of an impinging jet in a cross-flow configuration for electronics cooling applications
- 2013
-
Ingår i: Applied Thermal Engineering. - : Elsevier. - 1359-4311 .- 1873-5606. ; 52:2, s. 428-438
-
Tidskriftsartikel (refereegranskat)abstract
- A parametric study based on design of experiments (DoE) techniques was carried out by computational simulation in order to evaluate the effect that design parameters have on heat transfer and pressure loss of an impinging jet in a cross-flow configuration. The main effects of each parameter and the interactions between parameters were analyzed in detail through the Response Surface Methodology (RSM). Additionally, the potential of the impinging jet in a cross-flow configuration was assessed by calculating the optimal values of the parameters and comparing the cooling efficiency of the resulting configuration with the efficiency of the conventional cross-flow configuration. It was found that the degree to which the average heat transfer coefficient is enhanced as the result of adding an impinging jet depends on the height of the cooled component. Specifically, it was found that the higher the component, the more significant the enhancement.
|
|
| 7. |
- Martinez-Galvan, Eduardo, et al.
(författare)
-
Film Thickness and Heat Transfer Measurements in a Spray Cooling System With R134a
- 2011
-
Ingår i: Journal of Electronic Packaging. - : ASME International. - 1043-7398 .- 1528-9044. ; 133:1, s. 011002-
-
Tidskriftsartikel (refereegranskat)abstract
- Experimental measurements in a spray cooling test rig have been carried out for several heat fluxes in the heater and different spray volumetric fluxes with the dielectric refrigerant R134a. Results of the heat transfer and the sprayed refrigerant film thickness measurements are presented. The film thickness measurements have been made with a high speed camera equipped with a long distance microscope. It has been found that there is a relation between the variation in the average Nusselt number and the film thickness along the spray cooling boiling curve. The heat transfer regimes along that curve are related not only with a variation in the average Nusselt number but also with changes in the film thickness. The qualitative analysis of those variations has served to understand better the heat transfer mechanisms occurring during the spray cooling.
|
|
| 8. |
- Martinez-Galvan, Eduardo, et al.
(författare)
-
Influence of surface roughness on a spray cooling system with R134a. Part I : Heat transfer measurements
- 2013
-
Ingår i: Experimental Thermal and Fluid Science. - : Elsevier BV. - 0894-1777 .- 1879-2286. ; 46, s. 183-190
-
Tidskriftsartikel (refereegranskat)abstract
- Experimental measurements in a spray cooling test rig were carried out for two different heater surface roughnesses and for two different types of nozzles with the dielectric refrigerant R134a. In this paper, results of the heat transfer measurements are presented. The analysis of the results explains the influence of the volumetric flow rate, the surface roughness and the type of nozzle (through the spray parameters) on the spray cooling boiling curve, on the Nusselt number and on the efficiency. It has been found that the effect of a smooth roughness is to delay the onset of the nucleate boiling, but once this regime has started, boiling is so fast that the CHF (Critical Heat Flux) is reached at lower heater temperatures and lower heat fluxes. In a companion paper the sprayed refrigerant film thickness measurements and its relation with the heat transfer measurements are presented.
|
|
| 9. |
- Martinez-Galván, Eduardo, et al.
(författare)
-
Influence of surface roughness on a spray cooling system with R134a. Part II : Film thickness measurements
- 2013
-
Ingår i: Experimental Thermal and Fluid Science. - : Elsevier. - 0894-1777 .- 1879-2286. ; 48, s. 73-80
-
Tidskriftsartikel (refereegranskat)abstract
- Experimental measurements in a spray cooling test rig were carried out for two different heater surface roughnesses and for two different types of nozzles with the dielectric refrigerant R134a. In this paper, results of the sprayed refrigerant film thickness measurements are presented. The influence of the volumetric flow rate, the surface roughness and the type of nozzle (through the spray parameters) on the total average film thickness is analyzed and discussed. In a companion paper, results of the heat transfer measurements are presented. It has been found that there is a relation between the variations of the average Nusselt number and of the film thickness along the spray cooling boiling curve. The heat transfer regimes along that curve are related not only to a variation in the average Nusselt number but also to changes in the film thickness. The qualitative analysis of those variations served to better understand the heat transfer mechanisms occurring during the spray cooling.
|
|
| 10. |
- Masip, Yunesky, et al.
(författare)
-
Experimental study of the turbulent flow around a single wall-mounted cube exposed to a cross-flow and an impinging jet
- 2012
-
Ingår i: International Journal of Heat and Fluid Flow. - : Elsevier. - 0142-727X .- 1879-2278. ; 38, s. 50-71
-
Tidskriftsartikel (refereegranskat)abstract
- The air flow around a cubic obstacle mounted on one wall of a rectangular channel was studied experimentally. The obstacle represents an electronic component and the channel the space between two parallel printed circuit boards (PCBs). The flow was produced by the combination of a channel stream and a jet which issued from a circular nozzle placed at the wall opposite from where the component is mounted. With this aim, a test rig was designed and built to carry out experiments with both the above mentioned configurations and other cooling arrangements. Planar Particle Image Velocimetry (PIV) was employed to measure the instantaneous flow velocity on several planes covering the space around the component. The mean velocity and the Reynolds stresses were obtained from averaging the instantaneous velocity, and the mean flow showed a complex pattern with different features such as recirculation bubbles, vortices, detachment and reattachment zones. The influence of two parameters, namely the channel Reynolds number and the jet-to-channel Reynolds number ratio, on these flow features was studied considering nine cases that combined three values of the channel Reynolds number (3410, 5752 and 8880) and three values of the ratio (0.5, 1.0 and 1.5). The results show that the Reynolds number ratio determines the drag produced on the jet and the deflection from its geometric axis due to the channel stream. In all the cases corresponding to the lowest value of the ratio, the jet was dragged and did not impact the component. This fact accounts for the non-existence of the Upper Horseshoe Vortex and changes in the flow characteristics at the region over the component.
|
|
| 11. |
|
|
| 12. |
- Zhang, Ruiying, et al.
(författare)
-
Comparative phylogeography of two widespread magpies : importance of habitat preference and breeding behavior on genetic structure in China.
- 2012
-
Ingår i: Molecular Phylogenetics and Evolution. - : Elsevier BV. - 1055-7903 .- 1095-9513. ; 65:2, s. 562-72
-
Tidskriftsartikel (refereegranskat)abstract
- Historical geological events and climatic changes are believed to have played important roles in shaping the current distribution of species. However, sympatric species may have responded in different ways to such climatic fluctuations. Here we compared genetic structures of two corvid species, the Azure-winged Magpie Cyanopica cyanus and the Eurasian Magpie Pica pica, both widespread but with different habitat dependence and some aspects of breeding behavior. Three mitochondrial genes and two nuclear introns were used to examine their co-distributed populations in East China and the Iberian Peninsula. Both species showed deep divergences between these two regions that were dated to the late Pliocene/early Pleistocene. In the East Chinese clade of C. cyanus, populations were subdivided between Northeast China and Central China, probably since the early to mid-Pleistocene, and the Central subclade showed a significant pattern of isolation by distance. In contrast, no genetic structure was found in the East China populations of P. pica. We suggest that the different patterns in the two species are at least partly explained by ecological differences between them, especially in habitat preference and perhaps also breeding behavior. These dissimilarities in life history traits might have affected the dispersal and survival abilities of these two species differently during environmental fluctuations.
|
|
