| 1. |
- Atak, Gamze, et al.
(författare)
-
Cycling durability and potentiostatic rejuvenation of electrochromic tungsten oxide thin films : Effect of silica nanoparticles in LiClO4-Propylene carbonate electrolytes
- 2023
-
Ingår i: Solar Energy Materials and Solar Cells. - : Elsevier. - 0927-0248 .- 1879-3398. ; 250
-
Tidskriftsartikel (refereegranskat)abstract
- Electrochromic (EC) technology allows control of the transmission of visible light and solar radiation through thin-film devices. When applied to “smart” windows, EC technology can significantly diminish energy use for cooling and air conditioning of buildings and simultaneously provide good indoor comfort for the buildings’ occupants through reduced glare. EC “smart” windows are available on the market, but it is nevertheless important that their degradation under operating conditions be better understood and, ideally, prevented. In the present work, we investigated EC properties, voltammetric cycling durability, and potentiostatic rejuvenation of sputter-deposited WO3 thin films immersed in LiClO4–propylene carbonate electrolytes containing up to 3.0 wt% of ∼7-nm-diameter SiO2 nanoparticles. Adding about 1 wt% SiO2 led to a significant improvement in cycling durability in the commonly used potential range of 2.0–4.0 V vs. Li/Li+. Furthermore, X-ray photoemission spectroscopy indicated that O–Si bonds were associated with enhanced durability in the presence of SiO2 nanoparticles.
|
|
| 2. |
- Atak, Gamze, et al.
(författare)
-
Durability studies of annealed electrochromic tungsten oxide films
- 2021
-
Ingår i: EMRS Fall Meeting 2021.
-
Konferensbidrag (övrigt vetenskapligt/konstnärligt)abstract
- In electrochromic (EC) applications, annealing is a crucial parameter not only for an individual layer but also for a full device. For the fabrication of a complete EC device, indium tin oxide (ITO) is often preferred as a transparent conductor layer. ITO films with high transparency and low electrical resistance are usually obtained by sputtering at high substrate temperatures. Consequently, the effect of high temperature on the EC layers can be very significant during sputtering of the ITO top layer for EC devices consisting of five sputtered layers on a single substrate. The role of annealing of a single layer of WO3 may also be important for EC performance. In the present work, we studied the effects of annealing on the durability of WO3 films. Thin films of WO3 were deposited by reactive DC magnetron sputtering in a mixture of Ar and O2 gases using an oxygen to argon ratio of 0.15. The total gas pressure was set to 4.0 Pa, and the sputtering power was 200 W. The WO3 films were deposited onto (i) unheated glass plates, (ii) such plates pre-coated with transparent and electrically conducting ITO with a sheet resistance of 60 Ω/square, and (iii) glass plates pre-coated with fluorine-doped tin oxide (FTO) with a sheet resistance of 14 Ω/square. Film thicknesses were 300±10 nm. After deposition of the films, the samples were annealed at 150, 300, 450, and 600 °C in ambient air for one h using a heating rate of 10 °C min-1. Cyclic voltammetry (CV) was performed for up to 500 cycles between 2.0 and 4.0 V vs. Li/Li+ at a scan rate of 20 mV s–1. Annealing at temperatures at and above 300 °C resulted in deteriorated electrochromic properties of the WO3 films i.e., a decreased transmittance variation. Charge density and coloration efficiency changes during extended electrochemical cycling were also observed as a function of cycle number and annealing temperature. It was found that the maximum optical transmittance modulation at a wavelength of 528 nm after 500 CV cycles was 69.3% for the film annealed at 150 °C.
|
|
| 3. |
- Atak, Gamze, et al.
(författare)
-
Electrochromic performance of WO3 films with different ITO layers
- 2019
-
Ingår i: EMRS Spring Meeting 2019..
-
Konferensbidrag (övrigt vetenskapligt/konstnärligt)abstract
- Electrochromic (EC) materials are able to change their optical properties such as transmission, absorption and reflection reversibly by application of an external voltage. EC metal oxides are divided into two groups: cathodic (coloring under ion insertion) and anodic (coloring under ion extraction). Tungsten oxide (WO3) is a well-known cathodic EC material and has been intensively studied in the last 30 years. EC materials and devices have been developed as an alternative to passive coating materials for light and heat management. Conventionally, an EC device is a construction with five-layers: transparent conducting oxide (TCO)/cathodic EC/ion conducting layer (liquid, gel or solid)/anodic EC/TCO, either all on one substrate or positioned between two substrates in a laminated configuration. Indium-tin oxide (ITO) coated substrates are used as a TCO electrode in EC applications due to their high conductivity and transparency.In this study, we deposited WO3 films onto ITO coated glass substrates with different sheet resistances (15, 30, 60 and 1000 Ω/□) by using DC magnetron sputtering technique. Optical and structural properties of ITO films were investigated. For durability studies, cyclic voltammetry data was recorded for up to 500 cycles between 2.0 and 4.0 V versus Li/Li+ at a scan rate of 20 mV s−1. Chronoamperometry measurements of the WO3 films were also performed. We measured the inserted and extracted charges as well as bleaching and coloring times of WO3 films with different ITO layer properties. Generally, ITO with low resistivity is preferred for the electrochemical measurements while absorption is low in the near-infrared region for ITO with higher resistivity. In this study, it is observed that the ITO with 60 Ω/□ sheet resistance is very suitable for optical and electrochromic measurements.
|
|
| 4. |
- Atak, Gamze, et al.
(författare)
-
Electrochromic tungsten oxide films prepared by sputtering : Optimizing cycling durability by judicious choice of deposition parameters
- 2021
-
Ingår i: Electrochimica Acta. - : Elsevier. - 0013-4686 .- 1873-3859. ; 367
-
Tidskriftsartikel (refereegranskat)abstract
- Thin films of W oxide were prepared by reactive DC magnetron sputtering (5 cm-diameter W target), and their electrochromic (EC) properties were investigated in an electrolyte of LiClO4 in propylene carbonate. The purpose of the study was to elucidate the role of critical deposition parameters-oxygen/argon gas flow ratio for the sputter plasma Gamma, total pressure in the sputter plasma p(tot) , and sputtering power P-s - on the EC performance with foci on electrochemical cycling durability and optical modulation range Delta T. Specifically, we used 0.15 <= Gamma <= 0.90, 5 <= p(tot) <= 30 mTorr, and 200 <= P-s <= 400 W and studied cycling durability for up to 500 voltammetric cycles in the range 2.0-4.0 V vs. Li/Li+ together with optical properties at a wavelength of 528 nm. Most significantly, we discovered that a judicious choice of deposition parameters could yield films with superior cycling durability. Thus a similar to 300 nm-thick film prepared at Gamma = 0.90, p(tot) = 10 mTorr, and P-s = 200 W showed Delta T approximate to 65% after an initial "training" during similar to 100 voltammetric cycles; higher values of p(tot), on the other hand, yielded films whose Delta Ts degraded by similar to 10% during the cycling, and a lower value of p(tot) led to dark films with only marginal electrochromism. Hence our work delineates a pathway towards W oxide films with excellent durability of the EC properties.
|
|
| 5. |
- Atak, Gamze, et al.
(författare)
-
Electrochromism of nitrogen-doped tungsten oxide thin films
- 2020
-
Ingår i: Materials Today. - : Elsevier BV. - 2214-7853. ; 33:6, s. 2434-2439
-
Tidskriftsartikel (refereegranskat)abstract
- Tungsten-oxide-based thin films were prepared by reactive DC magnetron sputtering in the presence ofoxygen and nitrogen. Nitrogen contents up to 12 at.% were documented by Rutherford backscattering spectrometry and time-of-flight elastic recoil detection analysis. Optical and electrochemical measurements showed that films with up to 4 at.% of nitrogen were as transparent as undoped tungsten oxide films and displayed enhanced electrochromic properties manifested in an increase in the coloration efficiency by as much as 20%.
|
|
| 6. |
- Atak, Gamze, et al.
(författare)
-
Nitrogen doped W oxide films for electrochromic applications
- 2019
-
Ingår i: EMRS Spring Meeting 2019.
-
Konferensbidrag (refereegranskat)abstract
- Electrochromic (EC) materials are able to change their optical properties such as transmission, absorption and reflection reversibly by application of an external voltage. EC metal oxides are divided into two groups: cathodic (coloring under ion insertion) and anodic (coloring under ion extraction). W oxide is a well-known cathodic EC material and its color changes from transparent to dark blue when ions are inserted.A desirable electrochromic material must have and maintain a high optical modulation, high coloration efficiency, fast coloration/bleaching switching kinetics and a stable charge/ discharge reversibility. In this study, W oxide films with different nitrogen levels were deposited by using reactive DC sputtering onto glass and ITO coated glass in Ar+O2+N2 atmosphere. For all films, the total gas pressure was set to 4.0 Pa, the Ar flow rate was kept at 50 ml/min, and the O2+N2 flow rate was kept at 7.5 ml/min. The optical, structural and electrochromic properties of undoped and N-doped W oxide films were investigated. The optical studies revealed that the average optical transmittance and band gap decreased (from 3.43 to 3.08 eV) due to N doping. It is shown that a small amount of nitrogen has promising effects on the EC performance (i.e. charge/discharge reversibility, optical modulation, coloration efficiency) of the WO3 films. It is observed that CE values increased by increasing N2 flow rate and its maximum value was 33.8 cm2/C. The maximum ΔT at 537 nm was 73.6% for an optimized N doped W oxide film.
|
|
| 7. |
- Atak, Gamze, et al.
(författare)
-
The role of oxygen to argon gas flow ratio on the durability of sputter-deposited electrochromic tungsten oxide films
- 2021
-
Ingår i: EMRS Fall Meeting 2021.
-
Konferensbidrag (övrigt vetenskapligt/konstnärligt)abstract
- Materials that are able to vary their transparency and coloration reversibly when they are subjected to an electrical current or voltage are referred to as “electrochromic” (EC). High optical transmittance modulation and long service lifetime are apparent requirements for EC materials used in smart windows technology. An extended service lifetime is provided by the long-term durability of the materials. One important aspect of durability is the ability to sustain charge transport between the EC film and electrolyte, or between the two EC films in a device, for many hundreds or thousands of cycles without any significant changes in the performance such as optical modulation and inserted-extracted charge. The purpose of this study is to clarify the effects of the oxygen-argon gas flow ratio during sputter deposition on the durability of WO3 films. In this study, the oxygen to argon gas-flow ratio was modulated by setting the O2 flow rate to 7.5, 15.0, 22.5, and 45.0 ml min-1 and using a fixed Ar flow rate of 50 ml min-1. Thus, the oxygen to argon gas-flow ratio was varied from 0.15 to 0.90. The pressure in the sputter plasma was set as 30 mTorr and the sputter power was maintained at 200 W. For durability studies, cyclic voltammetry data were recorded for up to 500 cycles between 2.0 and 4.0 V versus Li/Li+ at a scan rate of 20 mV s-1. High oxygen to argon gas ratio was found to have a positive effect on the EC properties of the films. When the long-term performance of the films was examined, it was seen that all the samples displayed a slow decline of the colored-state transmittance due to ion accumulation in the host material. After 500 color-bleach cycles, the maximum optical transmittance modulation between colored and bleached states at a wavelength of 528 nm was 63.6% when the oxygen to argon gas-flow ratio was 0.90.
|
|
| 8. |
- Bayrak Pehlivan, Ilknur, et al.
(författare)
-
Bifunctional solar electrocatalytic water splitting using CIGS solar modules and WO3-based electrolyzers
- 2019
-
Ingår i: EMRS Spring Meeting 2019.
-
Konferensbidrag (refereegranskat)abstract
- Using energy from the sun to produce a fuel and finally obtaining only water as an exhaust is a promising future technology for renewable energy and environmental sustainability. Solar driven water splitting is a method to produce hydrogen from solar energy. Coupling a solar cell with an electrolyzer is the approach with highest technological readiness. CuInxGa1-xSe2 (CIGS) is here a promising solar cell material for water splitting because it is possible to tune the band gap between 1.0 and 1.7 eV by changing the ratio between Ga and In, thus enabling maximum power point matching with an electrolyzer. Tungsten oxide is known as a photocatalytic material and mainly used for the oxygen evolution reaction in a water splitting process. However, WO3 films also show electrochromic activity together with hydrogen evolution. This result is interesting because it shows that WO3 films can be used as bifunctional materials for both hydrogen and oxygen evolution in water splitting, and provide additional functionalities to the system. In this study, WO3 films coated at different sputtering conditions on Ni foam and indium tin oxide substrates were investigated in the potential range of the hydrogen evolution reaction. The best overpotential of 164 mV vs. RHE at 10 mA/cm2 was obtained for WO3 films on Ni foam in 0.5 M H2SO4. The lowest potential needed for 10 mA/cm2 was measured 1.768 V for the electrolyzers consisting WO3 films on Ni foam as the cathode and non-coated Ni foam as the anode. Optimum solar-to-hydrogen (STH) efficiency of the CIGS solar cell modules and the electrolyzers was examined for different band gaps of the CIGS modules and sputtering conditions of WO3 films. Operation points of the combined system were calculated from the intersection of the voltage-current density curves for the CIGS modules and the electrolyzers. The results showed that the detailed sputtering conditions were not very critical to obtain high STH efficiency, indicating that the system could be robust and easily manufactured. The best-matched band gap of the CIGS was 1.19 eV and the highest STH efficiency of the CIGS driven WO3-based electrolyzers was 12.98 %.
|
|
| 9. |
- Bayrak Pehlivan, Ilknur, et al.
(författare)
-
Electrochromic solar water splitting using a cathodic WO3 electrocatalyst
- 2021
-
Ingår i: Nano Energy. - : Elsevier. - 2211-2855 .- 2211-3282. ; 81
-
Tidskriftsartikel (refereegranskat)abstract
- Solar-driven water splitting is an emerging technology with high potential to generate fuel cleanly and sustainably. In this work, we show that WO3 can be used as a cathodic electrocatalyst in combination with (Ag,Cu) InGaSe2 solar cell modules to produce hydrogen and provide electrochromic functionality to water splitting devices. This electrochromic effect can be used to monitor the charge state or performance of the catalyst for process control or for controlling the temperature and absorbed heat due to tunable optical modulation of the electrocatalyst. WO3 films coated on Ni foam, using a wide range of different sputtering conditions, were investigated as cathodic electrocatalysts for the water splitting reaction. The solar-to-hydrogen (STH) efficiency of solar-driven water electrolysis was extracted using (Ag,Cu)InGaSe2 solar cell modules with a cell band gap varied in between 1.15 and 1.25 eV with WO3 on Ni foam-based electrolyzers and yielded up to 13% STH efficiency. Electrochromic properties during water electrolysis were characterized for the WO3 films on transparent substrate (indium tin oxide). Transmittance varied between 10% and 78% and the coloration efficiency at a wavelength of 528 nm and the overpotential of 400 mV was 40 cm(2) C-1. Hydrogen ion consumption in ion intercalation for electrochromic and hydrogen gas production for water electrolysis processes was discussed.
|
|
| 10. |
- Sorar, Idris, et al.
(författare)
-
Durability and rejuvenation of electrochromic tungsten oxide thin films in LiClO4-propylene carbonate viscous electrolyte : Effect of Ti doping of the film and polyethylene oxide addition to the electrolyte
- 2023
-
Ingår i: Solid State Sciences. - : Elsevier. - 1293-2558 .- 1873-3085. ; 137
-
Tidskriftsartikel (refereegranskat)abstract
- Tungsten oxide and titanium doped tungsten oxide thin films, deposited by sputtering, were immersed in a viscous electrolyte comprised of LiClO4 in propylene carbonate and 2.0 wt% of polyethylene oxide (PEO). Electrochromic properties of the films were investigated by electrochemical techniques and in situ transmittance measurements. Cyclic voltammetry data were taken in the voltage ranges 2.0–4.0 and 1.5–4.0 V vs Li/Li+ for up to 500 cycles. A potentiostatic rejuvenation treatment was then performed on the degraded electrochromic films, at 6.0 V for 20 h, which was subsequently followed by another cyclic voltammetry measurement. Titanium incorporation into tungsten oxide resulted in a small cyclic stability improvement in the 2.0–4.0-V range, whereas less pronounced effects were observed for cycling in the 1.5–4.0-V range. Combining the results of the present study with our previous work, we are able to assess the relative merits of titanium incorporation and PEO addition to the electrolyte for the durability of electrochromic tungsten oxide thin films. Titanium addition was found advantageous for electrochemical durability in the 2.0–4.0-V range, but no clear benefits of PEO in the electrolyte were seen. On the other hand, in the wider 1.5–4.0-V range, tungsten oxide exhibited better durability than titanium-containing films, and this was especially so after rejuvenation in the PEO-containing electrolyte.
|
|
