| 1. |
- Aad, G., et al.
(författare)
-
- 2010
-
swepub:Mat__t
|
|
| 2. |
- Frey, B. N., et al.
(författare)
-
Cooling Yb-Doped Silica Fibers and Fiber Lasers with Anti-Stokes Pumping
- 2023
-
Ingår i: Proceedings of SPIE - The International Society for Optical Engineering. - : SPIE - International Society for Optical Engineering. - 9781510659797
-
Konferensbidrag (refereegranskat)abstract
- Optical cooling in Yb-doped silica fibers using anti-Stokes fluorescence has become a subject of great interest in the fiber laser community. This paper provides an update on the development of silica fibers designed specifically to enhance their cooling properties. This growing list includes a new, nearly single-mode fiber with a borophosphosilicate core that produced –65 mK of cooling with only 260 mW of 1040-nm pump power. The silica compositions that have now been successfully cooled at atmospheric pressure by anti-Stokes fluorescence by our team include aluminosilicate, aluminofluorosilicate, borophosphosilicate, and aluminosilicate doped with one of three different alkali-earth nanoparticles (Ba, Sr, and Ca). By fitting the measured temperature dependence of the cooled fiber on pump power, two key parameters that control the degree of cooling are inferred, namely the critical quenching concentration and the absorptive loss due to impurities. The inferred values compiled for the fibers that cooled indicate that the extracted heat is highest when the Yb concentration is 2 wt.% or more (to maximize heat extraction), the Al concentration is ~0.8 wt.% or greater (to reduce quenching), and the absorptive loss is below approximately 15 dB/km, and ideally below 5 dB/km (to minimize heating due to pump absorption). Only two of the reported fibers, an LaF3-doped and an LuF3-doped nanoparticle fiber, did not cool, because their Yb and Al concentrations were not sufficiently high. This analysis shows that through careful composition control (especially the Al and Yb concentrations) and minimization of the OH contamination, a new generation of Yb-doped silica fibers is emerging with higher Yb concentrations, greater resistance to quenching, and lower residual loss than commercial Yb-doped fibers. They can be expected to have a significant impact not only on optically cooled devices but also on a much broader range of fiber lasers and amplifiers.
|
|
| 3. |
- Knall, J. M., et al.
(författare)
-
Experimental observation of cooling in Yb-doped silica fibers
- 2020
-
Ingår i: Proceedings of SPIE - The International Society for Optical Engineering. - : SPIE - International Society for Optical Engineering. - 9781510633599
-
Konferensbidrag (refereegranskat)abstract
- Anti-Stokes fluorescence cooling in a silica-based fiber is reported for the first time. The fiber had a core with a 20-μm diameter doped with 2.06 wt.% Yb and co-doped with 0.86 wt.% Al and 0.88 wt.% F. Core-pumping the fiber with 1040- nm light, temperature changes as large at -50 mK were measured at atmospheric pressure. Temperature measurements were performed at 12 pump wavelengths, and the measured dependence of the temperature change as a function of pump wavelength was in excellent agreement with a previously reported model. With this model, the absorptive loss in the fiber was inferred to be less than 15 dB/km, and the critical quenching concentration to be ∼15.6 wt.% Yb. This combination of low loss and high quenching concentration (a factor of 16 times higher than the highest reported values for Yb-doped silica) is what allowed the observation of cooling. The temperature measurements were performed at atmospheric pressure using a custom slow-light fiber Bragg grating sensor with an improved thermal contact between the test fiber and the FBG. The improved method involves isopropanol to establish a good thermal contact between the two fibers. This eliminated a source of heating and enabled more accurate measurements of the cooled-fiber temperature. This improved temperaturemeasurement set-up also led to a new cooling record in a multimode Yb-doped ZBLAN fiber at atmospheric pressure. When pumped at 1030 nm, the fiber cooled by -3.5 K, a factor of 5.4 times higher than the previous record.
|
|
| 4. |
- Knall, J., et al.
(författare)
-
Radiation-balanced silica fiber laser
- 2021
-
Ingår i: Optica. - 2334-2536. ; 8:6, s. 830-833
-
Tidskriftsartikel (refereegranskat)abstract
- In optically pumped lasers, heat generated by the quantum defect causes detrimental fluctuations in the output mode, frequency, and power. Common heat-mitigation techniques use bulky mechanical coolers that introduce vibrations, leading to laser frequency and amplitude noise. Here, we present a radiation-balanced fiber laser, optically cooled by anti-Stokes fluorescence (ASF). The gain medium is a silica fiber with a 21-µm-diameter core doped with 2.06 wt. % Yb3+ and co-doped with Al2O3 and F- to reduce concentration quenching. The laser was core-pumped at 1040 nm to create both gain at 1065 nm and ASF cooling at atmospheric pressure. We demonstrate a maximum output power of 114 mW with a slope efficiency of 41% while maintaining near-zero average temperature change. This result could enable the development of fiber lasers with unprecedented coherence and stability.
|
|
| 5. |
- Ballato, J., et al.
(författare)
-
Material approaches to thermal management in advanced fiber lasers and amplifiers
- 2023
-
Ingår i: Proceedings of SPIE - The International Society for Optical Engineering. - : SPIE - International Society for Optical Engineering. - 9781510659797
-
Konferensbidrag (refereegranskat)abstract
- For as long as light and matter have partnered, impurities have played a role in optical system performance. This remains generally true for photonic heat engines and especially the case for optical refrigeration. Building on the history of light and glass, including the materials development of low loss telecom fibers, this paper briefly discusses the sources of heat generation in materials and all-material means for their reduction. Particularly attention will be paid to active optical fibers and connect thermal management to parasitic optical nonlinearities, both critical to high and low power amplifier and laser systems.
|
|
| 6. |
- Balliu, Enkeleda, PhD student, et al.
(författare)
-
High-efficiency radiation-balanced Yb-doped silica fiber laser with 200-mW output
- 2024
-
Ingår i: Optics Letters. - : Optica Publishing Group. - 0146-9592 .- 1539-4794. ; 49:8, s. 2021-2024
-
Tidskriftsartikel (refereegranskat)abstract
- The focus of this study was the development of a second generation of fiber lasers internally cooled by anti-Stokes fluorescence. The laser consisted of a length of a single-mode fiber spliced to fiber Bragg gratings to form the optical resonator. The fiber was single-moded at the pump (1040 nm) and signal (1064 nm) wavelengths. Its core was heavily doped with Yb, in the initial form of CaF2 nanoparticles, and co-doped with Al to reduce quenching and improve the cooling efficiency. After optimizing the fiber length (4.1 m) and output-coupler reflectivity (3.3%), the fiber laser exhibited a threshold of 160 mW, an optical efficiency of 56.8%, and a radiation-balanced output power (no net heat generation) of 192 mW. On all three metrics, this performance is significantly better than the only previously reported radiation-balanced fiber laser, which is even more meaningful given that the small size of the single-mode fiber core (7.8-µm diameter). At the maximum output power (∼2 W), the average fiber temperature was still barely above room temperature (428 mK). This work demonstrates that with anti-Stokes pumping, it is possible to induce significant gain and energy storage in a small-core Yb-doped fiber while keeping the fiber cool.
|
|
| 7. |
- Hawkins, T. W., et al.
(författare)
-
Kilowatt power scaling of an intrinsically low Brillouin and thermo-optic Yb-doped silica fiber
- 2021
-
Ingår i: Journal of the Optical Society of America. B, Optical physics. - 0740-3224 .- 1520-8540. ; 38:12, s. F38-F49
-
Tidskriftsartikel (refereegranskat)abstract
- The performance of optical fibers is dependent on both the fiber design and the materials from which it is made. While much of the development over the past few decades has focused on fiber geometry and microstructuring, more recent analyses have shown clear benefits of addressing parasitic nonlinearities at the origins of their light–matter interactions. Reported here are results on intrinsically low Brillouin and thermo-optic core fibers, fabricated using modified chemical vapor deposition. Specifically, fibers in the Yb-doped Al2O3−P2O5−B2O3−SiO2 system are developed based on how each glass constituent affects the material parameters that enable both stimulated Brillouin scattering (SBS) and transverse mode instability (TMI). One fiber, developed to be very heavily doped, exhibited thermo-optic and Brillouin gain coefficients up to ∼3 dB and 6 dB below conventional laser fibers, respectively. A second fiber, designed to approximate a commercial double-clad laser fiber, which necessitated lower doping levels, was output power scaled to over 1 kW with an efficiency over 70% and no observed photodarkening under conventional testing. Design curves for the enabling material properties that drive TMI and SBS also are provided as functions of compositions as a tool for the community to further study and develop intrinsically low-nonlinearity fiber lasers.
|
|
