| 1. |
- Ongena, J., et al.
(författare)
-
Recent progress on JET towards the ITER reference mode of operation at high density
- 2001
-
Ingår i: Plasma Physics and Controlled Fusion. - 0741-3335 .- 1361-6587. ; 43, s. A11-A30
-
Tidskriftsartikel (refereegranskat)abstract
- Recent progress towards obtaining high density and high confinement in JET as required for the ITER reference scenario at Q = 10 is summarized. Plasmas with simultaneous confinement H-98(y.2) = 1 and densities up to n/n(Gw) similar to 1 are now routinely obtained. This has been possible (i) by using plasmas at high (delta similar to 0.5) and medium (delta similar to 0.3-0.4) triangularity with sufficient heating power to maintain Type I ELMs, (ii) with impurity seeded plasmas at high (delta similar to 0.5) and low (delta less than or equal to 0.2) triangularity, (iii) with an optimized pellet injection sequence, maintaining the energy confinement and raising the density, and (iv) by carefully tuning the gas puff rate leading to plasmas with peaked density profiles and good confinement at long time scales. These high performance discharges exhibit Type I ELMs, with a new and more favourable behaviour observed at high densities, requiring further studies. Techniques for a possible mitigation of these ELMs are discussed, and first promising results are obtained with impurity seeding in discharges at high triangularity. Scaling studies using the new data of this year show a strong dependence of confinement on upper triangularity, density and proximity to the Greenwald limit. Observed MHD instabilities and methods to avoid these in high density and high confinement plasmas are discussed.
|
|
| 2. |
- Loarte, A., et al.
(författare)
-
Characterization of pedestal parameters and edge localized mode energy losses in the Joint European Torus and predictions for the International Thermonuclear Experimental Reactor
- 2004
-
Ingår i: Physics of Plasmas. - : AIP Publishing. - 1070-664X .- 1089-7674. ; 11:5, s. 2668-2678
-
Tidskriftsartikel (refereegranskat)abstract
- This paper presents the experimental characterization of pedestal parameters, edge localized mode (ELM) energy, and particle losses from the main plasma and the corresponding ELM energy fluxes on plasma facing components for a series of dedicated experiments in the Joint European Torus (JET). From these experiments, it is demonstrated that the simple hypothesis relating the peeling-ballooning linear instability to ELM energy losses is not valid. Contrary to previous observations at lower triangularities, small energy losses at low collisionality have been obtained in regimes at high plasma triangularity and q(95)similar to4.5, indicating that the edge plasma magnetohydrodynamic stability is linked with the transport mechanisms that lead to the loss of energy by conduction during type I ELMs. Measurements of the ELM energy fluxes on the divertor target show that their time scale is linked to the ion transport along the field and the formation of a high energy sheath, in agreement with kinetic modeling of ELMs. Higher density ELMs, of a convective nature, lead to overall much longer time scales for the ELM energy flux, with more than 80% of the ELM energy flux arriving after the surface divertor temperature has reached its maximum value. On the contrary, for low density ELMs, of a conductive nature, up to 40% of the energy flux arrives at the divertor target before the surface divertor temperature has reached its maximum value. These large and more conductive ELMs may lead to up to similar to50% of the ELM energy reaching the main wall plasma facing components instead of the divertor target. The extrapolation to the International Thermonuclear Experimental Reactor of the obtained results is described and the main uncertainties discussed.
|
|
| 3. |
- Goto, M, et al.
(författare)
-
Refinement of the automated method for human islet isolation and presentation of a closed system for in vitro islet culture
- 2004
-
Ingår i: Transplantation. - 1534-6080 .- 0041-1337. ; 78, s. 1367-1375
-
Tidskriftsartikel (refereegranskat)abstract
- Background. The procedure of human islet isolation needs further optimization and standardization. Here, we describe techniques to enhance enzymatic digestion and minimize mechanical forces during the digestion process. The isolation protocol has also been modified to meet current GMP (cGMP) standards. Moreover, the impact of donor- and process-related factors was correlated to the use of islets for clinical transplantation. Methods. One hundred twelve standardized consecutive islet isolations were evaluated. Metyltioninklorid and indermil (topical tissue adhesive) were applied to detect leakage of collagenase injected and to repair the damaged pancreatic glands. The effects of dye and glue were evaluated in terms of islet yield, islet function using the perifusion assay, and success rate of the isolation. To analyze key factors for successful isolations, both univariate and multivariate regression analysis were performed. Results. Both Metyltioninklorid and Indermil were effective to prevent leakage of enzyme solutions from the pancreatic glands. Both islet yield and success rate were higher when these tools were applied (4,516.1 +/- 543.0 vs. 3,447.7 +/- 323.5, P=0.02; 50.0% vs. 21.3%, P=0.02, respectively). No adverse effects on islet function or collagenase activity were observed. Multivariate regression analysis identified the maximal recorded amylase >100 U/L (P=0.026), BMI (P=0.03), and the use of catecholamine (P=0.04) as crucial donor-related factors. In addition, cold ischemia time (P=0.005), the dissection procedure using whole glands with duodenum (P=0.02), and the local procurement team (P=0.03) were identified as crucial isolation-related variables. Conclusions. A standardized technique of islet isolation is presented applying novel means to improve enzymatic digestion and to meet cGMP standards.
|
|
| 4. |
- Seekamp, J, et al.
(författare)
-
Nanoimprinted passive optical devices
- 2002
-
Ingår i: Nanotechnology. - : IOP Publishing. - 0957-4484. ; 13:5, s. 581-586
-
Tidskriftsartikel (refereegranskat)abstract
- We report on the feasibility and process parameters of nanoimprint lithography to fabricate low refractive index passive optical devices. Diffraction gratings printed in polymethylmethacrylate (PMMA) exhibit a sharp dispersion with a full width at half maximum of about 20 nm. Waveguides were printed in polystyrene (PS) on silicon oxide and had losses between 8-20 dB cm(-1) at wavelengths between 650-400 nm, respectively. Finally, one-dimensional photonic structures were also printed in PS and their transmission and morphology characterized. The expected Bragg peak was observed in transmission and atomic force microscopy images have shown a good pattern transfer. A square lattice was printed in PMMA and more than 40 print cycles were obtained, i.e., potentially more than 1000 imprints from one master stamp.
|
|
