| 1. |
- Bechta, Sevostian, et al.
(författare)
-
INTERACTION BETWEEN MOLTEN CORIUM UO2+x-ZrO2-FeOy AND VVER VESSEL STEEL
- 2010
-
Ingår i: Nuclear Technology. - : American Nuclear Society. - 0029-5450 .- 1943-7471. ; 170:1, s. 210-218
-
Tidskriftsartikel (refereegranskat)abstract
- In case of in-vessel corium retention during a severe accident in a light water reactor, weakening of the vessel wall and deterioration of the vessel steel properties can be caused both by the melting of the steel and by its physicochemical interaction with corium. The interaction behavior has been studied in medium-scale experiments with prototypic corium. The experiments yielded data for the steel corrosion rate during interaction with UO2+x-ZrO2-FeOy melt in air and steam at different steel surface temperatures and heat fluxes from the corium to the steel. It has been observed that the corrosion rates in air and steam atmosphere are almost the same. Further, if the temperature at the interface increases beyond a certain level, corrosion intensifies. This is explained by the formation of liquid phases in the interaction zone. The available experimental data have been used to develop a correlation for the corrosion rate as afunction of temperature and heat flux.
|
|
| 2. |
- Buerger, M., et al.
(författare)
-
Coolability of particulate beds in severe accidents : Status and remaining uncertainties
- 2010
-
Ingår i: Progress in nuclear energy (New series). - : Elsevier BV. - 0149-1970 .- 1878-4224. ; 52:1, s. 61-75
-
Tidskriftsartikel (refereegranskat)abstract
- Particulate debris beds may form during different stages of a severe core melt accident; e.g. in the degrading hot core, due to thermal stresses during reflooding, in the lower plenum, by melt flow from the core into water in the lower head, and in the cavity by melt flow out of a failing RPV into a wet cavity. Deep water pools in the cavity are used in Nordic BWRs as an accident management measure aiming at particulate debris formation and coolability. It has been elaborated in the joint work of the European Severe Accident Research Network (SARNET) in Work Package (WP) 11.1 that coolability of particulate debris, reflooding of hot debris as well as boil-off under decay heat (long-term coolability), is strongly favoured by 2D/3D effects in beds with non-homogeneous structure and shape. Especially, water inflow from the sides and via bottom regions strongly improves coolability as compared to 1D situations with top flooding, the latter being in the past the basis of analyses on coolability. Data from experiments included in the SARNET network (DEBRIS at IKE and STYX at VTT) and earlier ones (e.g. POMECO at KTH) have been used to validate key constitutive laws in 2D codes as WABE (IKE) and ICARE/CATHARE (IRSN), especially concerning flow friction and heat transfer. Major questions concern the need of the explicit use of interfacial friction to adequately treat the various flow situations in a unified approach, as well as the adequate characterization of realistic debris composed of irregularly shaped particles of different sizes. joint work has been supported by transfer of the WABE code to KTH and VTT. Concerning realistic debris, the formation from breakup of melt jets in water is investigated in the DEFOR experiments at KTH. Present results indicate that porosities in the debris might be much higher than previously assumed, which would strongly support attainment of coolability. Calculations have been performed with IKEJET/IKEMIX describing jet breakup, mixing and settling of resulting particles. Models about debris bed formation and porosity are developed at KTH. The codes have been applied to reactor conditions for analysing the potential for coolability in the different phases of a severe accident. Calculations have been performed with WABE (MEWA) implemented in ATHLET-CD and with ICARE/ICATHARE for degraded cores and debris beds in the lower plenum, under reflooding and boil-off. Ex-vessel situations have also been analysed. Strong effects of lateral water inflow and cooling by steam in hot areas have been demonstrated. In support, some typical basic configurations have been analysed, e.g. configurations with downcomers considered as possible AM measures. Melt pool formation or coolability of particulate debris is a major issue concerning melt retention in the core and the lower head. Present conclusions from those analyses for adequate modelling in ASTEC are outlined as well as remaining uncertainties. Experimental and analysis efforts and respective continued joint actions are discussed, which are needed to reach resolution of the coolability issue.
|
|
| 3. |
- Miassoedov, A., et al.
(författare)
-
Corium and debris coolability studies performed in the severe accident research network of excellence (SARNET2)
- 2012
-
Ingår i: Proceedings Of The 20th International Conference On Nuclear Engineering And The ASME 2012 Power Conference - 2012, Vol 2. - : ASME Press. ; , s. 383-392
-
Konferensbidrag (refereegranskat)abstract
- The motivation of the work performed within the work package "Corium and Debris Coolability" of the Severe Accident Research Network of Excellence (SARNET) is to reduce or possibly solve the remaining uncertainties on the efficiency of cooling reactor core structures and materials during severe accidents, either in the core, in the vessel lower head or in the reactor cavity, so as to limit the progression of the accident. This can be achieved either by ensuring corium retention within the reactor pressure vessel or at least by limiting the corium progression and the rate of corium release into the cavity. These issues are to be covered within the scope of accident management for existing reactors and within the scope of design and safety evaluation of future reactors. The specific objectives are to create and enhance the database on debris formation, debris coolability and corium behavior in the lower head, to develop and validate the models and computer codes for simulation of in-vessel debris bed and melt pool behavior, to perform reactor scale analysis for in-vessel corium coolability and to assess the influence of severe accident management measures on in-vessel coolability. The work being performed within this work package comprises experimental and modeling activities with strong cross coupling between the tasks. Substantial knowledge and understanding of governing phenomena concerning coolability of intact rod-like reactor core geometry was obtained in previous projects. Hence the main thrust of experimental and modeling efforts concentrates mainly on the study of formation and cooling of debris beds in order to demonstrate effective cooling modes, cooling rates and coolability limits. Modeling efforts have been aimed at assessing and validating the models in system-level and detailed codes for core degradation, oxidation and debris behavior. The paper describes the work performed up to now and summarizes the main results achieved so far.
|
|
