| 1. |
- Kumara, Chamara, et al.
(författare)
-
Microstructure modelling of laser metal powder directed energy deposition of alloy 718
- 2019
-
Ingår i: Additive Manufacturing. - : Elsevier. - 2214-8604 .- 2214-7810. ; 25, s. 357-364
-
Tidskriftsartikel (refereegranskat)abstract
- A multi-component and multi-phase-field modelling approach, combined with transformation kinetics modelling, was used to model microstructure evolution during laser metal powder directed energy deposition of Alloy 718 and subsequent heat treatments. Experimental temperature measurements were utilised to predict microstructural evolution during successive addition of layers. Segregation of alloying elements as well as formation of Laves and δ phase was specifically modelled. The predicted elemental concentrations were then used in transformation kinetics to estimate changes in Continuous Cooling Transformation (CCT) and Time Temperature Transformation (TTT) diagrams for Alloy 718. Modelling results showed good agreement with experimentally observed phase evolution within the microstructure. The results indicate that the approach can be a valuable tool, both for improving process understanding and for process development including subsequent heat treatment.
|
|
| 2. |
- Hanning, Fabian, 1988, et al.
(författare)
-
Investigation of the Effect of Short Exposure in the Temperature Range of 750-950 degrees C on the Ductility of Haynes (R) 282 (R) by Advanced Microstructural Characterization
- 2019
-
Ingår i: Metals. - : MDPI. - 2075-4701. ; 9:12
-
Tidskriftsartikel (refereegranskat)abstract
- A Gleeble-based test method has been developed to study the change in the ductility signature of Haynes (R) 282 (R) during isothermal exposure from 5 s to 1800 s. A temperature range of 750 to 950 degrees C has been used to investigate the effect of age-hardening reactions. Microstructural constituents have been analyzed and quantified using scanning and transmission electron microscopy. Carbides present in the material are identified as primary MC-type TiC carbides, Mo-rich M6C secondary carbides, and Cr-rich M23C6 secondary carbides. Gamma prime (gamma’) precipitates are present in all the material conditions with particle sizes ranging from 2.5 nm to 58 nm. Isothermal exposure causes the growth of gamma’ and development of a grain boundary carbide network. A ductility minimum is observed at 800-850 degrees C. The fracture mode is found to be dependent on the stroke rate, where a transition toward intergranular fracture is observed for stroke rates below 0.055 mm/s. Intergranular fracture is characterized by microvoids present on grain facets, while ductility did not change during ongoing age-hardening reactions for intergranularly fractured Haynes (R) 282 (R).
|
|
| 3. |
- Kumara, Chamara, et al.
(författare)
-
Predicting the Microstructural Evolution of Electron Beam Melting of Alloy 718 with Phase-Field Modeling
- 2019
-
Ingår i: Metallurgical and Materials Transactions A: Physical Metallurgy and Materials Science. - : Springer Science and Business Media LLC. - 1073-5623 .- 1543-1940. ; 50:5, s. 2527-2537
-
Tidskriftsartikel (refereegranskat)abstract
- Electron beam melting (EBM) is a powder bed additive manufacturing process where a powder material is melted selectively in a layer-by-layer approach using an electron beam. EBM has some unique features during the manufacture of components with high-performance superalloys that are commonly used in gas turbines such as Alloy 718. EBM has a high deposition rate due to its high beam energy and speed, comparatively low residual stresses, and limited problems with oxidation. However, due to the layer-by-layer melting approach and high powder bed temperature, the as-built EBM Alloy 718 exhibits a microstructural gradient starting from the top of the sample. In this study, we conducted modeling to obtain a deeper understanding of microstructural development during EBM and the homogenization that occurs during manufacturing with Alloy 718. A multicomponent phase-field modeling approach was combined with transformation kinetic modeling to predict the microstructural gradient and the results were compared with experimental observations. In particular, we investigated the segregation of elements during solidification and the subsequent “in situ” homogenization heat treatment at the elevated powder bed temperature. The predicted elemental composition was then used for thermodynamic modeling to predict the changes in the continuous cooling transformation and time–temperature transformation diagrams for Alloy 718, which helped to explain the observed phase evolution within the microstructure. The results indicate that the proposed approach can be employed as a valuable tool for understanding processes and for process development, including post-heat treatments.
|
|
| 4. |
- Rakoczy, Łukasz, et al.
(författare)
-
Microstructure evolution of the Gleeble-simulated heat-affected zone of Ni-based superalloy
- 2019
-
Ingår i: Power Transmissions 2019 Proceedings. ; 3
-
Konferensbidrag (refereegranskat)abstract
- The formation of liquation cracking in a simulated heat affected zone of René108 is reported. The stress controlled thermo-mechanical experiments were carried out on a Gleeble®3800 testing system. The base alloy was lost-wax cast and then solution treated and aged. Light and scanning electron microscopy of this material revealed high volume fraction of γ' precipitates in the dendrite arms and residual eutectic γ/γ' islands in the interdendritic areas. As a result of short-term exposure to high homologous temperature, the volume fraction of γ' phase was significantly decreased due to the dissolution of precipitates in the surrounding matrix. The thin non-equilibrium liquid film, formed locally along grain boundaries, was a key-factor favoring initiation of cracks and their spreading during the Gleeble testing. The liquid appeared as a result of constitutional liquation, mainly of the γ' precipitates.
|
|
