| 1. |
- Andersson, Helene, 1983, et al.
(författare)
-
Effects of molecular weight on permeability and microstructure of mixed ethyl-hydroxypropyl-cellulose films
- 2013
-
Ingår i: European Journal of Pharmaceutical Sciences. - : Elsevier BV. - 0928-0987 .- 1879-0720. ; 48:1-2, s. 240-248
-
Tidskriftsartikel (refereegranskat)abstract
- Films of ethyl cellulose (EC) and water-soluble hydroxypropyl cellulose (HPC) can be used for extended release coatings in oral formulations. The permeability and microstructure of free EC/HPC films with 30% w/w HPC were studied to investigate effects of EC molecular weight. Phase separation during film spraying and subsequent HPC leaching after immersion in aqueous media cause pore formation in such films. It was found that sprayed films were porous throughout the bulk of the films after water immersion. The molecular weight affected HPC leaching, pore morphology and film permeability; increasing the molecular weight resulted in decreasing permeability. A model to distinguish the major factors contributing to diffusion retardation in porous films showed that the trend in permeability was determined predominantly by factors associated with the geometry and arrangement of pores, independent of the diffusing species. The film with the highest molecular weight did, however, show an additional contribution from pore wall/permeant interactions. In addition, rapid drying and increasing molecular weight resulted in smaller pores, which suggest that phase separation kinetics affects the final microstructure of EC/HPC films. Thus, the molecular weight influences the microstructural features of pores, which are crucial for mass transport in EC/HPC films.
|
|
| 2. |
- Larsson, Mikael, 1982, et al.
(författare)
-
Effect of ethanol on the water permeability of controlled release films composed of ethyl cellulose and hydroxypropyl cellulose
- 2010
-
Ingår i: European Journal of Pharmaceutics and Biopharmaceutics. - : Elsevier BV. - 1873-3441 .- 0939-6411. ; 76:3, s. 428-432
-
Tidskriftsartikel (refereegranskat)abstract
- The robustness of controlled release formulations when co-ingested with alcohol is a current concern expressed by regulatory authorities, especially with regard to dose dumping. One such controlled release formulation commonly used is film coating composed of ethyl cellulose (EC) and hydroxypropyl cellulose (HPC). The aim of this study was to investigate how the presence of ethanol in the dissolution medium affects the water permeability of such films. Film samples were prepared in various EC–HPC compositions, and the effect of different ethanol concentrations in the dissolution medium on the permeability was studied using a modified Ussing chamber and tritiated water. It was found that the effect of ethanol on the film permeability varied depending on the composition of the films. The results were interpreted in terms of swelling of the EC in the films, where the swelling increased with increasing ethanol concentration. Thus, for films with low HPC content (non-interconnected pores), the water permeability of the films increased with increasing ethanol concentration as the diffusion through the ethyl cellulose increased due to swelling. However, for films with higher HPC content (having interconnected pores through the films), the permeability decreased, likely due to the swelling of the ethyl cellulose blocking the pores. The interpretation of the results was supported by dynamic mechanic analysis and SEM analysis.
|
|
| 3. |
- Larsson, Mikael, 1982, et al.
(författare)
-
Novel nanostructured microfibrillated cellulose–hydroxypropyl methylcellulose films with large one-dimensional swelling and tunable permeability
- 2012
-
Ingår i: Carbohydrate Polymers. - : Elsevier BV. - 0144-8617. ; 88:2, s. 763-771
-
Tidskriftsartikel (refereegranskat)abstract
- Microfibrillated cellulose (MFC) films containing the water soluble and pharmaceutically approved polymer hydroxypropyl methylcellulose (HPMC) exhibited an unexpected decrease in permeability and excellent one-dimensional swelling properties above a threshold in HPMC content. It is proposed that the observed material characteristics derive from the influence of HPMC on the aggregation behavior of MFC in such a way that above a critical HPMC content the films are created through self assembly into a layered structure, composed of low swelling layers with swellable inter layer regions. The suggested structures were supported by high resolution microscopy. The findings should hold potential for direct applications, but even more as a concept for future material design.
|
|
