| 1. |
- Axelson, Olav, 1937-, et al.
(författare)
-
Regulatory toxicology and pharmacology.
- 2003
-
Ingår i: International journal of occupational and environmental health. - 1077-3525 .- 2049-3967. ; 9, s. 386-389
-
Tidskriftsartikel (refereegranskat)
|
|
| 2. |
|
|
| 3. |
- Das, D. K., et al.
(författare)
-
Effect of Al content on microstructure and cyclic oxidation performance of Pt-aluminide coatings
- 2002
-
Ingår i: Oxidation of Metals. - 0030-770X .- 1573-4889. ; 57:3-4, s. 245-266
-
Tidskriftsartikel (refereegranskat)abstract
- The effect of Al content, i.e., the amount of Al picked up during aluminizing, on the microstructure and cyclic oxidation properties of Pt-aluminide coatings has been investigated. The cast Ni-base superalloy CM-247 was used as the substrate material and a single-step, high-activity pack aluminizing process was used to produce the Pt-aluminide coatings. The Al content of these coatings was varied by using packs with different compositions of the Al source. Pt-aluminide coatings having three different Al contents, namely 6.5, 16, and 21 mg cm-2, were evaluated for their cyclic oxidation resistance at 1200°C in air. It was found that the Pt-aluminide coatings, irrespective of their Al contents, evolve in the same manner during aluminizing and result in a three-layer structure with an outer PtAl2 + NiAl two-phase layer, an intermediate NiAl layer, and the inner interdiffusion layer. The stability of this three-layer coating structure over long periods of aluminizing, however, is dependent on the availability of Al from the pack during this period. Below a certain threshold Al availability, the two-phase outer layer transforms to a single-phase NiAl structure causing the coating to change from its three-layer structure to a two-layer one. Cyclic oxidation results indicate that, while a minimum Al content in Pt-aluminide coatings is essential for deriving the best oxidation performance, increasing the Al content beyond a certain level does not significantly enhance oxidation behavior. The effect of Al content on aspects, such as coating degradation and nature of coating-surface damage during cyclic oxidation, is also discussed.
|
|
| 4. |
- Das, D. K., et al.
(författare)
-
Effect of prealuminizing diffusion treatment on microstructural evolution of high-activity pt-aluminide coatings
- 2000
-
Ingår i: Metallurgical and Materials Transactions. A. - 1073-5623 .- 1543-1940. ; 31:8, s. 2037-2047
-
Tidskriftsartikel (refereegranskat)abstract
- The effect of prealuminizing (or prior) diffusion treatment on the evolution of Pt-aluminide coatings on the Ni-based superalloy CM-247 has been studied by using a single-step, high-activity aluminizing process. Coatings generated without any prior diffusion treatment, as well as those formed by adopting two extreme prior-diffusion schedules (at 850 °C for 0.5 hours and at 1034 °C for 5 hours), were investigated by analyzing the coating structures at various stages of aluminizing. When the dilution of the Pt layer, caused by its interdiffusion with the substrate during the prior diffusion treatment, is only marginal (as in the case of no prior diffusion and diffusion at 850 °C for 0.5 hours), the equilibrium Pt-aluminide coating structure evolves through the formation of two transient layers during the initial stages of aluminizing. In contrast, for diffusion at 1034 °C for 5 hours, which results in extensive dilution of the Pt layer, the two-phase equilibrium structure (PtAl2 in a matrix of NiAl) in the outer layer of the coating is found to develop during very early stages of aluminizing and remains unchanged, even over extended periods of aluminizing. Further, in the case of prior diffusion at 1034 °C for 5 hours, Pt is found to remain distributed to a greater extent over the entire thickness of the coating than in the cases of limited prior diffusion treatment. The present findings underline the significance of the nature of the prior-diffusion schedule on the microstructural evolution of Pt-aluminide coatings. It has also been found that a prealuminizing diffusion treatment is particularly important for Pt-aluminide coatings from the point of view of coating adhesion to the substrate.
|
|
| 5. |
- DAS, D.K., et al.
(författare)
-
High temperature oxidation behaviour of directionally solidified nickel base superalloy CM–247LC
- 2003
-
Ingår i: Materials Science and Technology. - : Informa UK Limited. - 0267-0836 .- 1743-2847. ; 19:6, s. 695-708
-
Tidskriftsartikel (refereegranskat)abstract
- The present paper describes the isothermal and cyclic oxidation behaviour of the technologically important nickel base directionally solidified superalloy CM-247LC in air in the temperature range 1000-1200°C. This superalloy behaves as a transition nickel base alloy under isothermal oxidation conditions and exhibits a fairly long transient oxidation period (~20 h at 1100°C). Irrespective of the temperature of exposure and nature of oxidation (isothermal or cyclic), a composite oxide scale develops on CM-247LC. While the outer portion of the oxide scale consists of either spinel (NiAl2O4) or a mixture of spinel and NiO, depending on oxidation temperature, the inner portion is always constituted of alumina. Beyond the transient period, the alloy is found to follow parabolic oxidation kinetics. The oxide layer that forms is invariably very non-uniform in thickness, and is dispersed with two types of oxide particles. While tantalum rich oxide particles are found scattered in the outer zone of the oxide layer, hafnium rich oxide particles lie close to the oxide/metal interface. Results also reveal that the nature of oxidation associated with the CM-247LC superalloy causes entrapment of metal islands in the oxide layer.
|
|
| 6. |
- Joshi, S. V., et al.
(författare)
-
Influence of Laser Glazing on the Characteristics and Tribological Performance of Plasma and Detonation Sprayed WC-Co Coatings
- 2001
-
Ingår i: Proceedings of the International Thermal Spray Conference. ; , s. 583-592
-
Konferensbidrag (refereegranskat)abstract
- This paper deals with a comprehensive evaluation of the laser glazing or re-melting route as a possible means of specifically enhancing the performance of thermal sprayed WC-Co coatings. In the present study, a high-power continuous-wave 9kW CO2 laser was utilized for laser treatment of plasma sprayed as well as detonation sprayed WC-Co coatings. The influence of the two most important laser-related variables, namely laser power and scan speed, on the properties of the laser-treated layers was investigated. Both mere surface densification by melting a thin top layer of the coating as well as melting of the entire portion of the coated layer were targeted during laser treatment. In each case, the laser treated coatings were fully characterized by optical microscopy, scanning electron microscopy, and microhardness measurements. In addition, the influence of laser processing on the elemental distribution, phase constitution and extent of defects in the treated layers was investigated. The tribological performance of the laser-glazed coatings was also evaluated and compared against the performance of their as-sprayed counterparts. The study has revealed significant differences between the response of plasma and detonation sprayed WC-Co layers when subjected to laser treatment. The potential of plasma-sprayed coatings to match the performance of the inherently superior detonation sprayed coatings by adopting laser glazing as a post-processing step has also been assessed.
|
|
| 7. |
- Saravanan, P., et al.
(författare)
-
Application of Taguchi method to the optimization of detonation spraying process
- 2000
-
Ingår i: Materials and Manufacturing Processes. - New York, NY, United States : Marcel Dekker Inc. - 1042-6914 .- 1532-2475. ; 15:1, s. 139-153
-
Tidskriftsartikel (refereegranskat)abstract
- The present study deals with an application of the Taguchi method to the optimization of a detonation spray process for alumina coatings. Coating experiments were conducted using the Taguchi-fractional factorial (L8) design parametric study to optimize spray process parameters. The Taguchi design evaluated the effects of four detonation spray process parameters: acetylene to oxygen ratio, carrier gas flow rate, frequency of detonations and spray distance. The coating qualities evaluated were surface roughness, porosity, microhardness, and abrasion mass loss. The influence of process parameters on the as-sprayed coating qualities is discussed. The results of the study indicate that the higher fuel ratio and lower spray distance will result in higher hardness, lower porosity and lower abrasion mass loss. The Taguchi analysis employed in the present investigation led to optimized process parameters for the most abrasive wear resistant alumina coatings.
|
|
| 8. |
- Saravanan, P., et al.
(författare)
-
Influence of process variables on the quality of detonation gun sprayed alumina coatings
- 2000
-
Ingår i: Surface & Coatings Technology. - Lausanne, Switzerland : Elsevier Sequoia SA. - 0257-8972 .- 1879-3347. ; 123:1, s. 44-54
-
Tidskriftsartikel (refereegranskat)abstract
- Detonation gun (D-gun) spraying is one of the most promising thermal spray variants for depositing high quality wear resistant coatings. Of all the ceramic materials that can be D-gun sprayed, alumina (Al2O3) is the most widely established and these coatings have already gained industrial acceptance for diverse applications. The present study deals with a statistical design of experimental study of the D-gun spraying of Al2O3 powder. Coating experiments were conducted, using a Taguchi-full factorial (L16) design parametric study, to optimize the D-gun spray process parameters. Four selected important spraying parameters were considered in their upper and lower levels of the predefined range according to the test matrix, in order to display the range of processing conditions and their effect on the coating quality. Optical microscopy, scanning electron microscopy, X-ray diffraction, image analysis and hardness testing was used for characterization. Coating qualities are discussed with respect to surface roughness, hardness, porosity and microstructure. The attributes of the coatings are correlated with the changes in operating parameters and their relative importance and contribution ratios to overall variance are calculated. Detonation gun (D-gun) spraying is one of the most promising thermal spray variants for depositing high quality wear resistant coatings. Of all the ceramic materials that can be D-gun sprayed, alumina (Al2O3) is the most widely established and these coatings have already gained industrial acceptance for diverse applications. The present study deals with a statistical design of experimental study of the D-gun spraying of Al2O3 powder. Coating experiments were conducted, using a Taguchi-full factorial (L16) design parametric study, to optimize the D-gun spray process parameters. Four selected important spraying parameters were considered in their upper and lower levels of the predefined range according to the test matrix, in order to display the range of processing conditions and their effect on the coating quality. Optical microscopy, scanning electron microscopy, X-ray diffraction, image analysis and hardness testing was used for characterization. Coating qualities are discussed with respect to surface roughness, hardness, porosity and microstructure. The attributes of the coatings are correlated with the changes in operating parameters and their relative importance and contribution ratios to overall variance are calculated.
|
|
| 9. |
- Saravanan, P., et al.
(författare)
-
Study of plasma- and detonation gun-sprayed alumina coatings using Taguchi experimental design
- 2000
-
Ingår i: Journal of thermal spray technology (Print). - Materials Park, OH, United States : ASM International. - 1059-9630 .- 1544-1016. ; 9:4, s. 505-512
-
Tidskriftsartikel (refereegranskat)abstract
- Atmospheric plasma spraying (APS) is a most versatile thermal spray method for depositing alumina (Al2O3) coatings, and detonation gun (D-gun) spraying is an alternative thermal spray technology for depositing such coatings with extremely good wear characteristics. The present study is aimed at comparing the characteristics of Al2O3 coatings deposited using the above techniques by using Taguchi experimental design. Alumina coating experiments were conducted using a Taguchi fractional-factorial (L8) design parametric study to optimize the spray process parameters for both APS and D-gun. The Taguchi design evaluated the effect of four APS and D-gun spray variables on the measured coating attributes. The coating qualities evaluated were surface roughness, porosity, microhardness, abrasion, and sliding wear. The results show that the coating quality is directly related to the corresponding coating microstructure, which is significantly influenced by the spray parameters employed. Though it is evident that the D-gun-sprayed coatings consistently exhibit dense and uniform microstructure, higher hardness, and superior tribological performance, the attainment of suitable plasma-sprayed coatings can be improved by employing the Taguchi analysis.
|
|
