| 1. |
- Bader Eddin, Mohamad, et al.
(författare)
-
Prediction of Sound Insulation Using Artificial Neural Networks—Part II : Lightweight Wooden Façade Structures
- 2022
-
Ingår i: Applied Sciences (Switzerland). - : MDPI AG. - 2076-3417. ; 12:14
-
Tidskriftsartikel (refereegranskat)abstract
- A prediction model based on artificial neural networks is adapted to forecast the acoustic performance of airborne sound insulation of various lightweight wooden façade walls. A total of 100 insulation curves were used to develop the prediction model. The data are laboratory measurements of façade walls in one-third-octave bands (50 Hz–5 kHz). For each façade wall, geometric and physical information (material type, dimensions, thicknesses, densities, and more) are used as input parameters. The model shows a satisfactory predictive capability for airborne sound reduction. A higher accuracy is obtained at middle frequencies (250 Hz–1 kHz), while lower and higher frequency ranges often show higher deviations. The weighted airborne sound reduction index ((Formula presented.)) of façades can be estimated with a maximum difference of 3 dB. Sometimes, the model shows high variations within fundamental and critical frequencies that influence the predictive precision. A sensitivity analysis is implemented to investigate the significance of parameters in insulation estimations. The material density (i.e., cross-laminated timber panel, gypsum board), thickness of the insulation materials, thickness and spacing between interior studs and the total density of façades are factors of significant weight on predictions. The results also emphasize the importance of façade thickness and the total density of the clustered exterior layers.
|
|
| 2. |
- Eddin, Mohamad Bader, et al.
(författare)
-
A comparison of numerical approaches to quantify sound insulation of lightweight wooden floor structures
- 2022
-
Ingår i: Internoise 2022 - 51st International Congress and Exposition on Noise Control Engineering. - 9781906913427
-
Konferensbidrag (refereegranskat)abstract
- Quantifying air-borne and structure-borne sound insulation is an important design consideration for the indoor comfort in a building. Although sound insulation performance is commonly measured experimentally, numerical methods can have time-saving and economic benefits. Further, numerical methods can be incorporated within building simulations to provide an estimate of the acoustic environment. In response, this paper evaluates three different computational approaches for quantifying sound insulation in one-third octave bands (50 Hz -5 kHz) of a lightweight floor including: an analytical (theoretical) model, a finite element model (FEM), and an artificial neural network (ANN) model. The three numerical methods are tested on the sound insulation of a cross laminated timber (CLT) floor. The results of this study show that the ANN model is able to accurately predict the air-borne and impact sound insulation performance at frequencies above 250 Hz, but over-predicts the air-borne performance and under-predicts the impact performance at low frequencies. However, the analytical and FEM strategies provide acceptable estimations, useful during the conceptual design stage, but with higher deviations than ANN model across all frequencies. While no model is able to accurately represent acoustic behavior across all frequencies, this work highlights the advantages and disadvantages when applied to predicting the sound insulation of a CLT floor.
|
|
| 3. |
- Eddin, Mohamad Bader, et al.
(författare)
-
Prediction of Sound Insulation Using Artificial Neural Networks—Part I : LightweightWooden Floor Structures
- 2022
-
Ingår i: Acoustics. - : MDPI AG. - 2624-599X. ; 4:1, s. 203-226
-
Tidskriftsartikel (refereegranskat)abstract
- The artificial neural networks approach is applied to estimate the acoustic performance for airborne and impact sound insulation curves of different lightweight wooden floors. The prediction model is developed based on 252 standardized laboratory measurement curves in one-third octave bands (50-5000 Hz). Physical and geometric characteristics of each floor structure (materials, thickness, density, dimensions, mass and more) are utilized as network parameters. The predictive capability is satisfactory, and the model can estimate airborne sound better than impact sound cases especially in the middle-frequency range (250-1000 Hz), while higher frequency bands often show high errors. The forecast of the weighted airborne sound reduction index Rw was calculated with a maximum error of 2 dB. However, the error increased up to 5 dB in the worse case prediction of the weighted normalized impact sound pressure level Ln,w. The model showed high variations near the fundamental and critical frequency areas which affect the accuracy. A feature attribution analysis explored the essential parameters on estimation of sound insulation. The thickness of the insulation materials, the density of cross-laminated timber slab and the concrete floating floors and the total density of floor structures seem to affect predictions the most. A comparison between wet and dry floor solution systems indicated the importance of the upper part of floors to estimate airborne and impact sound in low frequencies.
|
|
| 4. |
- Eddin, Mohamad Bader, et al.
(författare)
-
Sound insulation of lightweight wooden floor structures : ANN model and sensitivity analysis
- 2022
-
Ingår i: Internoise 2022 - 51st International Congress and Exposition on Noise Control Engineering. - 9781906913427
-
Konferensbidrag (refereegranskat)abstract
- The study aims to develop an artificial neural networks (ANN) model to estimate the acoustic performance for airborne and impact sound insulation curves of different lightweight wooden floors. The prediction model is developed using 252 standardized laboratory measurement curves in one-third octave bands (50 − 5000 Hz). Each floor structure has been divided into three parts in the database: upper, main and ceiling parts. Physical and geometric characteristics (materials, thickness, density, dimensions, mass, and more) are used as network parameters. The results demonstrated that the predictive ability of the model is satisfactory. The forecast of the weighted airborne sound reduction index Rw was calculated with a maximum error of 2 dB. However, it is increased up to 5 dB in the worst case prediction of the weighted normalized impact sound pressure level Ln,w. A sensitivity analysis explored the essential parameters on sound insulation estimation. The thickness and the density of upper and main parts of the floors seem to affect estimations the most in all frequencies. In addition, no remarkable attribution has been found for the thickness and density of the ceiling part of the structures.
|
|
