| 1. |
- Tao, Qiang, 1987, et al.
(författare)
-
D-A(1)-D-A(2) Copolymers with Extended Donor Segments for Efficient Polymer Solar Cells
- 2015
-
Ingår i: Macromolecules. - : American Chemical Society (ACS). - 1520-5835 .- 0024-9297. ; 48:4, s. 1009-1016
-
Tidskriftsartikel (refereegranskat)abstract
- Typically a donor-acceptor (D-A) design strategy is used for engineering the bandgap of polymers for solar cells. However, in this work, a series of alternating D-A(1-)D-A(2) copolymers PnTQTI(F) were synthesized and characterized with oligothiophenes (nT, n = 1, 2, 3) as the donor and two electron-deficient moieties, quinoxaline and isoindigo, as the acceptors in the repeating unit. We have studied the influence of the donor segments with different numbers of thiophene units and the effect of the addition of fluorine to the quinoxaline unit of the D-A(1)-D-A(2) polymers. The photophysical, electrochemical, and photovoltaic properties of the polymers were examined via a range of techniques and related to theoretical simulations. On increasing the length of the donor thiophene units, broader absorption spectra were observed in addition to a sequential increase in HOMO levels, while the LUMO levels displayed very small variations. The addition of fluorine to the quinoxaline unit not only decreased the HOMO levels of the resulting polymers but also enhanced the absorption coefficients. A superior photovoltaic performance was observed for the P3TQTI-F-based device with a power conversion efficiency (PCE) of 7.0%, which is the highest efficiency for alternating D-A(1)-D-A(2) polymers reported to date. The structureproperty correlations of the PnTQTI(F) polymers demonstrate that varying of the length of the donor segments is a valuable method for designing high-performance D-A(1)-D-A(2) copolymers and highlight the promising nature of D-A(1)-D-A(2) copolymers for efficient bulk-heterojunction solar cells.
|
|
| 2. |
- Xu, Xiaofeng, 1984, et al.
(författare)
-
Pyrrolo[3,4-g]quinoxaline-6,8-dione-based conjugated copolymers for bulk heterojunction solar cells with high photovoltages
- 2015
-
Ingår i: Polymer Chemistry. - : ROYAL SOC CHEMISTRY. - 1759-9954 .- 1759-9962. ; 6:25, s. 4624-4633
-
Tidskriftsartikel (refereegranskat)abstract
- A new electron-deficient building block 5,9-di(thiophen-2-yl)-6H-pyrrolo[3,4-g]quinoxaline-6,8(7H)-dione (PQD) was synthesized via functionalizing the 6- and 7-positions of quinoxaline (Qx) with a dicarboxylic imide moiety. Side chain substitution on the PQD unit leads to good solubility which enables very high molecular weight copolymers to be attained. The fusion of two strong electron-withdrawing groups (Qx and dicarboxylic imide) makes the PQD unit a stronger electron-deficient moiety than if the unit had just one electron-withdrawing group, thus enhancing the intramolecular charge transfer between electron-rich and deficient units of the copolymer. Four PQD-based polymers were synthesized which feature deep-lying highest occupied molecular orbital (HOMO) levels and bathochromic absorption spectra when compared to PBDT-Qx and PBDT-TPD analogues. The copolymers incorporated with benzo[1,2-b:4,5-b]dithiophene (BDT) units show that the 1D and 2D structural variations of the side groups on the BDT unit are correlated with the device performance. As a result, the corresponding solar cells (ITO/PEDOT:PSS/polymer: PC71BM/LiF/Al) based on the four copolymers feature very high open-circuit voltages (V-oc) of around 1.0 V. The copolymer PBDT-PQD1 attains the best power conversion efficiency of 4.9%, owing to its relatively high absorption intensity and suitable film morphology. The structure-property correlation demonstrates that the new PQD unit is a promising electron-deficient building block for efficient photovoltaic materials with high V-oc.
|
|
| 3. |
- Bäcke, Olof, 1984, et al.
(författare)
-
Enhanced thermal stability of a polymer solar cell blend induced by electron beam irradiation in the transmission electron microscope
- 2017
-
Ingår i: Ultramicroscopy. - : Elsevier BV. - 1879-2723 .- 0304-3991. ; 173, s. 16-23
-
Tidskriftsartikel (refereegranskat)abstract
- We show by in situ microscopy that the effects of electron beam irradiation during transmission electron microscopy can be used to lock microstructural features and enhance the structural thermal stability of a nanostructured polymer:fullerene blend. Polymer:fullerene bulk-heterojunction thin films show great promise for use as active layers in organic solar cells but their low thermal stability is a hindrance. Lack of thermal stability complicates manufacturing and influences the lifetime of devices. To investigate how electron irradiation affects the thermal stability of polymer:fullerene films, a model bulk-heterojunction film based on a thiophene-quinoxaline copolymer and a fullerene derivative was heat-treated in-situ in a transmission electron microscope. In areas of the film that exposed to the electron beam the nanostructure of the film remained stable, while the nanostructure in areas not exposed to the electron beam underwent large phase separation and nucleation of fullerene crystals. UV–vis spectroscopy shows that the polymer:fullerene films are stable for electron doses up to 2000 kGy.
|
|
| 4. |
- Bäcke, Olof, 1984, et al.
(författare)
-
Enhanced thermal stability of a polymer solar cell blend induced by electron beam irradiation in the transmission electron microscope
- 2017
-
Ingår i: Ultramicroscopy. - : Elsevier BV. - 1879-2723 .- 0304-3991. ; 176:Spec. Issue, s. 23-30
-
Tidskriftsartikel (refereegranskat)abstract
- We show by in situ microscopy that the effects of electron beam irradiation during transmission electron microscopy can be used to lock microstructural features and enhance the structural thermal stability of a nanostructured polymer:fullerene blend. Polymer:fullerene bulk-heterojunction thin films show great promise for use as active layers in organic solar cells but their low thermal stability is a hindrance. Lack of thermal stability complicates manufacturing and influences the lifetime of devices. To investigate how electron irradiation affects the thermal stability of polymer:fullerene films, a model bulk-heterojunction film based on a thiophene-quinoxaline copolymer and a fullerene derivative was heat-treated in-situ in a transmission electron microscope. In areas of the film that exposed to the electron beam the nanostructure of the film remained stable, while the nanostructure in areas not exposed to the electron beam underwent large phase separation and nucleation of fullerene crystals. UV–vis spectroscopy shows that the polymer:fullerene films are stable for electron doses up to 2000 kGy.
|
|
| 5. |
- Bäcke, Olof, 1984, et al.
(författare)
-
Mapping fullerene crystallization in a photovoltaic blend: an electron tomography study
- 2015
-
Ingår i: Nanoscale. - : Royal Society of Chemistry (RSC). - 2040-3372 .- 2040-3364. ; 7:18, s. 8451-8456
-
Tidskriftsartikel (refereegranskat)abstract
- The formation of fullerene crystals represents a major degradation pathway of polymer/fullerene bulk-heterojunction thin films that inexorably deteriorates their photovoltaic performance. Currently no tools exist that reveal the origin of fullerene crystal formation vertically through the film. Here, we show that electron tomography can be used to study nucleation and growth of fullerene crystals. A model bulk-heterojunction blend based on a thiophene-quinoxaline copolymer and a fullerene derivative is examined after controlled annealing above the glass transition temperature. We image a number of fullerene nanocrystals, ranging in size from 70 to 400 nanometers, and observe that their center is located close to the free-surface of spin-coated films. The results show that the nucleation of fullerene crystals predominately occurs in the upper part of the films. Moreover, electron tomography reveals that the nucleation is preceded by more pronounced phase separation of the blend components.
|
|
| 6. |
- Diaz de Zerio Mendaza, Amaia, 1986, et al.
(författare)
-
A Fullerene Alloy Based Photovoltaic Blend with a Glass Transition Temperature above 200 °C
- 2017
-
Ingår i: Journal of Materials Chemistry A. - 2050-7488 .- 2050-7496. ; 5:8, s. 4156-4162
-
Tidskriftsartikel (refereegranskat)abstract
- Organic solar cells with a high degree of thermal stability require bulk-heterojunction blends that feature a high glass transition, which must occur considerably above the temperatures encountered during device fabrication and operation. Here, we demonstrate for the first time a polymer : fullerene blend with a glass transition temperature above 200 °C, which we determine by plasmonic nanospectroscopy. We achieve this strong tendency for glass formation through the use of an alloy of neat, unsubstituted C60 and C70, which we combine with the fluorothieno-benzodithiophene copolymer PTB7. A stable photovoltaic performance of PTB7 : C60 : C70 ternary blends is preserved despite annealing the active layer at up to 180 °C, which coincides with the onset of the glass transition. Rapid deterioration of the power conversion efficiency from initially above 5% only occurs upon exceeding the glass transition temperature of 224 °C of the ternary blend.
|
|
| 7. |
- Diaz de Zerio Mendaza, Amaia, 1986, et al.
(författare)
-
High-Entropy Mixtures of Pristine Fullerenes for Solution-Processed Transistors and Solar Cells
- 2015
-
Ingår i: Advanced Materials. - : Wiley. - 0935-9648 .- 1521-4095. ; 27:45, s. 7325-7331
-
Tidskriftsartikel (refereegranskat)abstract
- The solubility of pristine fullerenes can be enhanced by mixing C60 and C70 due to the associated increase in configurational entropy. This "entropic dissolution" allows the preparation of field-effect transistors with an electron mobility of 1 cm2 V-1 s-1 and polymer solar cells with a highly reproducible power-conversion efficiency of 6%, as well as a thermally stable active layer.
|
|
