| 1. |
- Abel, I, et al.
(författare)
-
Overview of the JET results with the ITER-like wall
- 2013
-
Ingår i: Nuclear Fusion. - : IOP Publishing. - 1741-4326 .- 0029-5515. ; 53:10, s. 104002-
-
Tidskriftsartikel (refereegranskat)abstract
- Following the completion in May 2011 of the shutdown for the installation of the beryllium wall and the tungsten divertor, the first set of JET campaigns have addressed the investigation of the retention properties and the development of operational scenarios with the new plasma-facing materials. The large reduction in the carbon content (more than a factor ten) led to a much lower Z(eff) (1.2-1.4) during L- and H-mode plasmas, and radiation during the burn-through phase of the plasma initiation with the consequence that breakdown failures are almost absent. Gas balance experiments have shown that the fuel retention rate with the new wall is substantially reduced with respect to the C wall. The re-establishment of the baseline H-mode and hybrid scenarios compatible with the new wall has required an optimization of the control of metallic impurity sources and heat loads. Stable type-I ELMy H-mode regimes with H-98,H-y2 close to 1 and beta(N) similar to 1.6 have been achieved using gas injection. ELM frequency is a key factor for the control of the metallic impurity accumulation. Pedestal temperatures tend to be lower with the new wall, leading to reduced confinement, but nitrogen seeding restores high pedestal temperatures and confinement. Compared with the carbon wall, major disruptions with the new wall show a lower radiated power and a slower current quench. The higher heat loads on Be wall plasma-facing components due to lower radiation made the routine use of massive gas injection for disruption mitigation essential.
|
|
| 2. |
- Romanelli, F, et al.
(författare)
-
Overview of the JET results
- 2011
-
Ingår i: Nuclear Fusion. - : IOP Publishing. - 1741-4326 .- 0029-5515. ; 51:9
-
Tidskriftsartikel (refereegranskat)abstract
- Since the last IAEA Conference JET has been in operation for one year with a programmatic focus on the qualification of ITER operating scenarios, the consolidation of ITER design choices and preparation for plasma operation with the ITER-like wall presently being installed in JET. Good progress has been achieved, including stationary ELMy H-mode operation at 4.5 MA. The high confinement hybrid scenario has been extended to high triangularity, lower ρ*and to pulse lengths comparable to the resistive time. The steady-state scenario has also been extended to lower ρ*and ν*and optimized to simultaneously achieve, under stationary conditions, ITER-like values of all other relevant normalized parameters. A dedicated helium campaign has allowed key aspects of plasma control and H-mode operation for the ITER non-activated phase to be evaluated. Effective sawtooth control by fast ions has been demonstrated with3He minority ICRH, a scenario with negligible minority current drive. Edge localized mode (ELM) control studies using external n = 1 and n = 2 perturbation fields have found a resonance effect in ELM frequency for specific q95values. Complete ELM suppression has, however, not been observed, even with an edge Chirikov parameter larger than 1. Pellet ELM pacing has been demonstrated and the minimum pellet size needed to trigger an ELM has been estimated. For both natural and mitigated ELMs a broadening of the divertor ELM-wetted area with increasing ELM size has been found. In disruption studies with massive gas injection up to 50% of the thermal energy could be radiated before, and 20% during, the thermal quench. Halo currents could be reduced by 60% and, using argon/deuterium and neon/deuterium gas mixtures, runaway electron generation could be avoided. Most objectives of the ITER-like ICRH antenna have been demonstrated; matching with closely packed straps, ELM resilience, scattering matrix arc detection and operation at high power density (6.2 MW m-2) and antenna strap voltages (42 kV). Coupling measurements are in very good agreement with TOPICA modelling. © 2011 IAEA, Vienna.
|
|
| 3. |
- Pegourie, B., et al.
(författare)
-
Deuterium inventory in Tore Supra : Coupled carbon-deuterium balance
- 2013
-
Ingår i: Journal of Nuclear Materials. - : Elsevier BV. - 0022-3115 .- 1873-4820. ; 438:Suppl., s. S120-S125
-
Tidskriftsartikel (refereegranskat)abstract
- This paper presents an analysis of the carbon-deuterium circulation and the resulting balance in Tore Supra over the period 2002-2007. Carbon balance combines the estimation of carbon gross erosion from spectroscopy, net erosion and deposition using confocal microscopy, lock-in thermography and SEM, and a measure of the amount of deposits collected in the vacuum chamber. Fuel retention is determined from post-mortem (PM) analyses and gas balance (GB) measurements. Special attention was paid to the deuterium outgassed during the nights and weekends of the experimental campaign (vessel under vacuum, Plasma Facing Components at 120 degrees C) and during vents (vessel at atmospheric pressure, PFCs at room temperature). It is shown that this outgassing is the main process reconciling the PM and GB estimations of fuel retention, closing the coupled carbon-deuterium balance. In particular, it explains why the deuterium concentration in deposits decreases with increasing depth.
|
|
| 4. |
- Brezinsek, S., et al.
(författare)
-
Overview of experimental preparation for the ITER-Like Wall at JET
- 2011
-
Ingår i: Journal of Nuclear Materials. - : Elsevier BV. - 0022-3115 .- 1873-4820. ; 415:1, s. S936-S942
-
Tidskriftsartikel (refereegranskat)abstract
- Experiments in JET with carbon-based plasma-facing components have been carried out in preparation of the ITER-Like Wall with beryllium main chamber and full tungsten divertor. The preparatory work was twofold: (i) development of techniques, which ensure safe operation with the new wall and (ii) provision of reference plasmas, which allow a comparison of operation with carbon and metallic wall. (i) Compatibility with the W divertor with respect to energy loads could be achieved in N-2 seeded plasmas at high densities and low temperatures, finally approaching partial detachment, with only moderate confinement reduction of 10%. Strike-point sweeping increases the operational space further by re-distributing the load over several components. (ii) Be and C migration to the divertor has been documented with spectroscopy and QMBs under different plasma conditions providing a database which will allow a comparison of the material transport to remote areas with metallic walls. Fuel retention rates of 1.0-2.0 x 10(21) D s(-1) were obtained as references in accompanied gas balance studies.
|
|
| 5. |
- Matthews, G. F., et al.
(författare)
-
JET ITER-like wall-overview and experimental programme
- 2011
-
Ingår i: Physica Scripta. - : Institute of Physics Publishing (IOPP). - 0031-8949 .- 1402-4896. ; T145, s. 014001-
-
Tidskriftsartikel (refereegranskat)abstract
- This paper reports the successful installation of the JET ITER-like wall and the realization of its technical objectives. It also presents an overview of the planned experimental programme which has been optimized to exploit the new wall and other JET enhancements in 2011/12.
|
|
| 6. |
- Tsitrone, E., et al.
(författare)
-
Multi machine scaling of fuel retention in 4 carbon dominated tokamaks
- 2011
-
Ingår i: Journal of Nuclear Materials. - : Elsevier BV. - 0022-3115 .- 1873-4820. ; 415:1, s. S735-S739
-
Tidskriftsartikel (refereegranskat)abstract
- In order to benchmark predictions for the in vessel tritium inventory in ITER, a survey of fuel retention measured in 4 carbon dominated tokamaks (TEXTOR, ASDEX Upgrade in the 2002-2003 carbon configuration, Tore Supra and JET) was performed, showing retention rates from similar to 1 g D/h in TEXTOR (L mode, limiter machine) up to similar to 6-12 g D/h in AUG (H mode, divertor machine). A simple scaling used for ITER predictions is applied for comparison with experimental values: (1) estimate of wall fluxes, (2) estimate of the gross carbon erosion, (3) estimate of the net erosion/redeposition assuming a redeposition fraction and (4) estimate of the retention rate using D/C ratio scalings. The validity of each step is discussed, showing that this approach yields the right order of magnitude, but tends to underestimate the experimental values unless a high wall flux, a low local redeposition fraction and/or a high D/C ratio are used.
|
|
| 7. |
- Webster, A. J., et al.
(författare)
-
Time-resonant tokamak plasma edge instabilities?
- 2014
-
Ingår i: Plasma Physics and Controlled Fusion. - : IOP Publishing. - 0741-3335 .- 1361-6587. ; 56:7, s. 075017-
-
Tidskriftsartikel (refereegranskat)abstract
- For a two week period during the Joint European Torus 2012 experimental campaign, the same high confinement plasma was repeated 151 times. The dataset was analysed to produce a probability density function (pdf) for the waiting times between edge-localized plasma instabilities (ELMs). The result was entirely unexpected. Instead of a smooth single peaked pdf, a succession of 4-5 sharp maxima and minima uniformly separated by 7-8 ms intervals was found. Here we explore the causes of this newly observed phenomenon, and conclude that it is either due to a naturally occurring self-organized plasma phenomenon or an interaction between the plasma and a real-time control system. If the maxima are a result of 'resonant' frequencies at which ELMs can be triggered more easily, then future ELM control techniques can, and probably will, use them. Either way, these results demand a deeper understanding of the ELM process.
|
|
| 8. |
- Widdowson, A., et al.
(författare)
-
Material migration patterns and overview of first surface analysis of the JET ITER-like wall
- 2014
-
Ingår i: Physica Scripta. - 0031-8949 .- 1402-4896. ; T159, s. 014010-
-
Tidskriftsartikel (refereegranskat)abstract
- Following the first JET ITER-like wall operations a detailed in situ photographic survey of the main chamber and divertor was completed. In addition, a selection of tiles and passive diagnostics were removed from the vessel and made available for post mortem analysis. From the photographic survey and results from initial analysis, the first conclusions regarding erosion, deposition, fuel retention and material transport during divertor and limiter phases have been drawn. The rate of deposition on inner and outer base divertor tiles and remote divertor corners was more than an order of magnitude less than during the preceding carbon wall operations, as was the concomitant deuterium retention. There was however beryllium deposition at the top of the inner divertor. The net beryllium erosion rate from the mid-plane inner limiters was found to be higher than for the previous carbon wall campaign although further analysis is required to determine the overall material balance due to erosion and re-deposition.
|
|
| 9. |
- Likonen, J., et al.
(författare)
-
First results and surface analysis strategy for plasma-facing components after JET operation with the ITER-like wall
- 2014
-
Ingår i: Physica Scripta. - 0031-8949 .- 1402-4896. ; T159, s. 014016-
-
Tidskriftsartikel (refereegranskat)abstract
- During the carbon wall operations of JET since 2001, an extensive post-mortem analysis programme has been carried out under the JET Task Force Fusion Technology and a similar analysis programme is underway for the JET-ILW tiles removed during the 2012 shutdown. The first post-mortem results from the JET ITER-like wall tiles have shown that the overall amount of deposition on the divertor tiles and on remote divertor areas has been reduced by more than an order of magnitude with respect to JET-C. In addition, the obtained data indicate a possible interaction between Be and W such as the formation of mixed Be-W layers. This could be due to the surface roughness of the tiles, or could be caused by diffusion or even alloying. Ion-beam analyses and secondary ion mass spectrometry techniques give only elemental information, so other techniques such as x-ray diffraction, x-ray photoelectron spectroscopy, secondary electron microscopy/energy dispersive x-ray spectroscopy and nuclear microprobing are required. Since the nature of deposition and erosion has changed during the JET-ILW operations, a change in the post-mortem analysis programme is needed. For example, no cross-sectional samples from the sloping parts of tiles 4 and 6 are required. A strategy for post-mortem analyses of the marker-coated tiles will be presented in this paper.
|
|
| 10. |
- Malaquias, A., et al.
(författare)
-
Development of ITER relevant laser techniques for deposited layer characterisation and tritium inventory
- 2013
-
Ingår i: Journal of Nuclear Materials. - : Elsevier BV. - 0022-3115 .- 1873-4820. ; 438:Suppl., s. S936-S939
-
Tidskriftsartikel (refereegranskat)abstract
- Laser Induced Breakdown Spectroscopy (LIBS) is a potential candidate to monitor the layer composition and fuel retention during and after plasma shots on specific locations of the main chamber and divertor of ITER. This method is being investigated in a cooperative research programme on plasma devices such as TEXTOR, FTU, MAGNUM-PSI and in other various laboratorial experiments. In this paper LIBS results from targets of D-H-rich carbon films and mixed W-Al-C deposits on bulk tungsten substrates are reported (simulating ITER-like deposits with Al as proxy for Be). Two independent methods, one to determine the relative elemental composition and the other the absolute contents of the target based on the experimental LIBS signals are proposed. The results show that LIBS has the capability to provide the relative concentrations of the elements on the deposited layer when the experimental conditions on the targets surface are identical to the calibration samples.
|
|
| 11. |
- Philipps, V., et al.
(författare)
-
Development of laser-based techniques for in situ characterization of the first wall in ITER and future fusion devices
- 2013
-
Ingår i: Nuclear Fusion. - : IOP Publishing. - 0029-5515 .- 1741-4326. ; 53:9, s. 093002-
-
Tidskriftsartikel (refereegranskat)abstract
- Analysis and understanding of wall erosion, material transport and fuel retention are among the most important tasks for ITER and future devices, since these questions determine largely the lifetime and availability of the fusion reactor. These data are also of extreme value to improve the understanding and validate the models of the in vessel build-up of the T inventory in ITER and future D-T devices. So far, research in these areas is largely supported by post-mortem analysis of wall tiles. However, access to samples will be very much restricted in the next-generation devices (such as ITER, JT-60SA, W7-X, etc) with actively cooled plasma-facing components (PFC) and increasing duty cycle. This has motivated the development of methods to measure the deposition of material and retention of plasma fuel on the walls of fusion devices in situ, without removal of PFC samples. For this purpose, laser-based methods are the most promising candidates. Their feasibility has been assessed in a cooperative undertaking in various European associations under EFDA coordination. Different laser techniques have been explored both under laboratory and tokamak conditions with the emphasis to develop a conceptual design for a laser-based wall diagnostic which is integrated into an ITER port plug, aiming to characterize in situ relevant parts of the inner wall, the upper region of the inner divertor, part of the dome and the upper X-point region.
|
|
| 12. |
- Rubel, Marek, et al.
(författare)
-
Overview of erosion-deposition diagnostic tools for the ITER-Like Wall in the JET tokamak
- 2013
-
Ingår i: Journal of Nuclear Materials. - : Elsevier BV. - 0022-3115 .- 1873-4820. ; 438, s. S1204-S1207
-
Tidskriftsartikel (refereegranskat)abstract
- This paper presents scientific and technical issues related to the development of erosion-deposition diagnostic tools for JET operated with the ITER-Like Wall: beryllium and tungsten marker tiles and several types of wall probes installed in the main chamber and in the divertor. Markers tiles are the standard limiter and divertor components additionally coated first with a thin sandwich of Ni-Be and Mo-W for, beryllium and tungsten markers, respectively. Both types of markers are embedded in regular arrays of limiter and divertor tiles. Coated W-Be probes are also inserted in the Be-covered Inconel cladding tiles on the central column. Other types of erosion-deposition diagnostic tools are: rotating collectors, deposition traps, louver clips, quartz microbalance and mirrors for the First Mirror Test at JET for ITER. The specific role of these tools is discussed in detail.
|
|
| 13. |
|
|
