| 1. |
- Caselli, Lucrezia, et al.
(author)
-
Boosting Membrane Interactions and Antimicrobial Effects of Photocatalytic Titanium Dioxide Nanoparticles by Peptide Coating
- 2024
-
In: Small. - : John Wiley and Sons Inc. - 1613-6810 .- 1613-6829.
-
Journal article (peer-reviewed)abstract
- Photocatalytic nanoparticles offer antimicrobial effects under illumination due to the formation of reactive oxygen species (ROS), capable of degrading bacterial membranes. ROS may, however, also degrade human cell membranes and trigger toxicity. Since antimicrobial peptides (AMPs) may display excellent selectivity between human cells and bacteria, these may offer opportunities to effectively “target” nanoparticles to bacterial membranes for increased selectivity. Investigating this, photocatalytic TiO2 nanoparticles (NPs) are coated with the AMP LL-37, and ROS generation is found by C11-BODIPY to be essentially unaffected after AMP coating. Furthermore, peptide-coated TiO2 NPs retain their positive ζ-potential also after 1–2 h of UV illumination, showing peptide degradation to be sufficiently limited to allow peptide-mediated targeting. In line with this, quartz crystal microbalance measurements show peptide coating to promote membrane binding of TiO2 NPs, particularly so for bacteria-like anionic and cholesterol-void membranes. As a result, membrane degradation during illumination is strongly promoted for such membranes, but not so for mammalian-like membranes. The mechanisms of these effects are elucidated by neutron reflectometry. Analogously, LL-37 coating promoted membrane rupture by TiO2 NPs for Gram-negative and Gram-positive bacteria, but not for human monocytes. These findings demonstrate that AMP coating may selectively boost the antimicrobial effects of photocatalytic NPs. © 2024 The Authors.
|
|
| 2. |
- Del Giudice, Alessandra, et al.
(author)
-
Towards natural care products : Structural and deposition studies of bio-based polymer and surfactant mixtures
- 2024
-
In: Colloids and Surfaces A: Physicochemical and Engineering Aspects. - 0927-7757. ; 698
-
Journal article (peer-reviewed)abstract
- Oppositely charged polymer-surfactant systems are expected to interact with formation of coacervate complexes near composition of charge-neutrality. Such behaviour is widely used in formulated products (e.g. household and personal care), where the co-deposition of coacervates and active ingredients on various surfaces is triggered by dilution. A transition towards the use of more sustainable ingredients is currently ongoing as a response to the need of more environmentally conscious choices in production, albeit slowed down by the often more complex and not fully understood bulk and interfacial behaviour of new ingredients. In this work, mixtures of a medium-chain fatty acid (sodium decanoate) and two grades of bio-based cationic modified inulin were studied. The phase behaviour was determined in a wide composition matrix. The formation of coacervate complexes was observed for the mixture with the higher charge density polymer at a surfactant concentration of 1–3 wt%, close to the surfactant critical micellar concentration in pure water. Such behaviour was confirmed by DLS and SAXS data, suggesting surfactant-polymer complexation in a concentrated phase of packed micelles with a micelle-to-micelle distance of ∼4.5 nm. In situ ellipsometry and neutron reflectometry experiments were conducted to study the effect on surface deposition when diluting. The ellipsometry showed an adsorbed mass of ∼1.3–1.9 mg/m2, consistent with the deposition of a coacervate layer, and considerably higher than the neat, adsorbed polymer layer of ∼0.3 mg/m2. In the case of the neutron reflectometry experiments, dilution was performed before contact with the surface (pre-mixing), and no adsorption of coacervates was observed, but rather the adsorption of a polymer layer (0.49–0.85 mg/m2). The different results obtained with the different techniques highlight the kinetic nature of bulk coacervate formation and deposition, and the competition between these two phenomena. Maximal deposition can be achieved if one can control this time window either by tuning the composition of the system or the experimental set-up, to mimic the conditions of a specific application.
|
|
