1. |
- Beal, Jacob, et al.
(författare)
-
Robust estimation of bacterial cell count from optical density
- 2020
-
Ingår i: Communications Biology. - : Springer Science and Business Media LLC. - 2399-3642. ; 3:1
-
Tidskriftsartikel (refereegranskat)abstract
- Optical density (OD) is widely used to estimate the density of cells in liquid culture, but cannot be compared between instruments without a standardized calibration protocol and is challenging to relate to actual cell count. We address this with an interlaboratory study comparing three simple, low-cost, and highly accessible OD calibration protocols across 244 laboratories, applied to eight strains of constitutive GFP-expressing E. coli. Based on our results, we recommend calibrating OD to estimated cell count using serial dilution of silica microspheres, which produces highly precise calibration (95.5% of residuals <1.2-fold), is easily assessed for quality control, also assesses instrument effective linear range, and can be combined with fluorescence calibration to obtain units of Molecules of Equivalent Fluorescein (MEFL) per cell, allowing direct comparison and data fusion with flow cytometry measurements: in our study, fluorescence per cell measurements showed only a 1.07-fold mean difference between plate reader and flow cytometry data.
|
|
2. |
- Lin, Baojun, et al.
(författare)
-
Balancing the pre-aggregation and crystallization kinetics enables high efficiency slot-die coated organic solar cells with reduced non-radiative recombination losses
- 2020
-
Ingår i: Energy & Environmental Science. - : Royal Society of Chemistry (RSC). - 1754-5692 .- 1754-5706. ; 13:8, s. 2467-2479
-
Tidskriftsartikel (refereegranskat)abstract
- Slot-die coating being compatible with the roll-to-roll technique has been regarded as a promising tool for upscaling the manufacturing of organic solar cells (OSCs). However, there has been a significant gap between the efficiencies of the state-of-the-art spin-coated devices and the scalable processed devices. The active layer morphology is crucial to achieve high efficiency in OSCs, which depends on the conditions of film fabrication. To figure out and optimize the slot-die coating process, a deeper understanding of the film formation kinetics is important. Herein, in situ measurements of the slot-die coating process based on the PM7:IT4F system are demonstrated to illustrate the aggregation and crystallization evolution at various die temperatures and substrate temperatures. OSCs with a high power conversion efficiency of 13.2% are achieved at 60 degrees C die temperature/60 degrees C substrate temperature due to the improved exciton dissociation, charge transport and suppressed non-radiative charge recombination. The optimized morphology is attributed to the balanced polymer pre-aggregation and small molecule crystallization kinetics. The unsuitable die temperature leads to overlarge phase separation and consequently inefficient exciton dissociation while the improper substrate temperature results in weak crystallization and the following shrunken carrier lifetime with strong non-radiative combination. This work provides fundamental understanding on the correlations among processing methodology, solution pre-aggregation, morphology formation kinetics, device physics and device performance and affords guidance for device optimization in scalable manufacturing.
|
|
3. |
- Wang, Yilin, et al.
(författare)
-
Control of the Crystallization and Phase Separation Kinetics in Sequential Blade-Coated Organic Solar Cells by Optimizing the Upper Layer Processing Solvent
- 2023
-
Ingår i: Advanced Energy Materials. - : Wiley. - 1614-6832 .- 1614-6840. ; 13:7
-
Tidskriftsartikel (refereegranskat)abstract
- Sequential deposition of the active layer in organic solar cells (OSCs) is favorable to circumvent the existing drawbacks associated with controlling the microstructure in bulk-heterojunction (BHJ) device fabrication. However, how the processing solvents impact on the morphology during sequential deposition processes is still poorly understood. Herein, high-efficiency OSCs are fabricated by a sequential blade coating (SBC) through optimization of the morphology evolution process induced by processing solvents. It is demonstrated that the device performance is highly dependent on the processing solvent of the upper layer. In situ morphology characterizations reveal that an obvious liquid–solid phase separation can be identified during the chlorobenzene processing of the D18 layer, corresponding to larger phase separation. During chloroform (CF) processing of the D18 layer, a proper aggregation rate of Y6 and favorable intermixing of lower and upper layers results in the enhanced crystallinity of the acceptor. This facilitates efficient exciton dissociation and charge transport with an inhibited charge recombination in the D18/CF-based devices, contributing to a superior performance of 17.23%. These results highlight the importance of the processing solvent for the upper layer in the SBC strategy and suggest the great potential of achieving optimized morphology and high-efficiency OSCs using the SBC strategy.
|
|