SwePub - sökning: L773:2352 1791

Numrering	Referens	Omslagsbild	Hitta
1.	Andersson Sundén, Erik, et al. (författare) An assessment of nitrogen concentrations from spectroscopic measurements in the JET and ASDEX upgrade divertor 2019 Ingår i: Nuclear Materials and Energy. - : Elsevier. - 2352-1791. ; 18, s. 147-152 Tidskriftsartikel (refereegranskat)abstract The impurity concentration in the tokamak divertor plasma is a necessary input for predictive scaling of divertor detachment, however direct measurements from existing tokamaks in different divertor plasma conditions are limited. To address this, we have applied a recently developed spectroscopic N II line ratio technique for measuring the N concentration in the divertor to a range of H-mode and L-mode plasma from the ASDEX Upgrade and JET tokamaks, respectively. The results from both devices show that as the power crossing the separatrix, P-sep, is increased under otherwise similar core conditions (e.g. density), a higher N concentration is required to achieve the same detachment state. For example, the N concentrations at the start of detachment increase from approximate to 2% to approximate to 9% as P-sep, is increased from approximate to 2.5 MW to approximate to 7 MW. These results tentatively agree with scaling law predictions (e.g. Goldston et al.) motivating a further study examining the parameters which affect the N concentration required to reach detachment. Finally, the N concentrations from spectroscopy and the ratio of D and N gas valve fluxes agree within experimental uncertainty only when the vessel surfaces are fully-loaded with N.
2.	Ashikawa, N., et al. (författare) Determination of retained tritium from ILW dust particles in JET 2020 Ingår i: Nuclear Materials and Energy. - : Elsevier BV. - 2352-1791. ; 22 Tidskriftsartikel (refereegranskat)abstract Quantitative tritium inventory in dust particles from campaigns in the JET tokamak with the carbon wall (2007–2009) and the ITER-like wall (ILW 2011–2012) were determined by the liquid scintillation counter and the full combustion method. A feature of this full combustion method is that dust particles were covered by a tin (Sn) which reached 2100 K during combustion under oxygen flow. The specific tritium inventory for samples from JET with carbon and with metal walls was measured and found to be similar. However, the total tritium inventory in dust particles from the ILW experiment was significantly smaller in comparison to the carbon wall due to the lower amount of dust particles generated in the presence of metal walls.
3.	Balbinot, L., et al. (författare) Multi-code estimation of DTT edge transport parameters 2023 Ingår i: Nuclear Materials and Energy. - : Elsevier BV. - 2352-1791. ; 34 Tidskriftsartikel (refereegranskat)abstract The main goal of the Divertor Tokamak Test facility (DTT) is to operate with a high value of power-exhaust-relevant parameter Psoz/R in plasma scenarios similar to those foreseen for the Demonstration Fusion Power Plant (DEMO) in terms of low collisionality and neutral opacity. For these unique characteristics, accurate modelling of the principal scenario is necessary for machine designing. In edge numerical codes, cross-field transport profiles have a high impact on modelling results. This work aims at providing a coherent set of transport parameters for DTT full-power (FP) single-null (SN) scenario edge modelling. To evaluate such parameters for DTT, a transport analysis on the current machine has been performed using SOLEDGE2D-EIRENE and SOLPS-ITER. The transport parameters to be used in the simulations of the DTT single-null scenario were selected using two complementary methods. The first is the modelling of JET and Alcator C-Mod (C-Mod) with SOLEDGE2D-EIRENE and SOLPS-ITER, validating transport parameters by comparing modelling results to experimental data from pulses which are considered DTT-relevant. JET pulses were selected with the highest auxiliary input power (from 29 to 33 MW), plasma current and toroidal field to better match DTT parameters; nitrogen and neon seeded pulses were selected to check possible seeding material dependencies. The considered C-Mod pulse better matches DTT plasma density and neutral opacity. Transport parameters are then scaled to DTT according to scaling laws. The second method derives the transport parameters by tuning their values inside the DTT separatrix to reproduce the pedestal profiles predicted by the EPED model via the Europed code and applied in DTT. The derived set of DTT transport parameters is consistent with the results obtained by modelling present machines, reproduces the expected heat flux decay length in detached conditions and, inside the separatrix, reproduces the predicted pedestal using transport parameters which are coherent with what is predicted by the quasi-linear turbulent model QuaLiKiz.
4.	Bernert, M., et al. (författare) Power exhaust by SOL and pedestal radiation at ASDEX Upgrade and JET 2017 Ingår i: Nuclear Materials and Energy. - : Elsevier. - 2352-1791. ; 12, s. 111-118 Tidskriftsartikel (refereegranskat)abstract Future fusion reactors require a safe, steady state divertor operation. A possible solution for the power exhaust challenge is the detached divertor operation in scenarios with high radiated power fractions. The radiation can be increased by seeding impurities, such as N for dominant scrape-off-layer radiation, Ne or Ar for SOL and pedestal radiation and Kr for dominant core radiation. Recent experiments on two of the all-metal tokamaks, ASDEX Upgrade (AUG) and JET, demonstrate operation with high radiated power fractions and a fully-detached divertor by N, Ne or Kr seeding with a conventional divertor in a vertical target geometry. For both devices similar observations can be made. In the scenarios with the highest radiated power fraction, the dominant radiation originates from the confined region, in the case of N and Ne seeding concentrated in a region close to the X-point. Applying these seed impurities for highly radiative scenarios impacts local plasma parameters and alters the impurity transport in the pedestal region. Thus, plasma confinement and stability can be affected. A proper understanding of the effects by these impurities is required in order to predict the applicability of such scenarios for future devices.
5.	Bobkov, V, et al. (författare) Impact of ICRF on the scrape-off layer and on plasma wall interactions : From present experiments to fusion reactor 2019 Ingår i: Nuclear Materials and Energy. - : Elsevier. - 2352-1791. ; 18, s. 131-140 Tidskriftsartikel (refereegranskat)abstract Recent achievements in studies of the effects of ICRF (Ion Cyclotron Range of Frequencies) power on the SOL (Scrape-Off Layer) and PWI (Plasma Wall Interactions) in ASDEX Upgrade (AUG), Alcator C-Mod, and JET-ILW are reviewed. Capabilities to diagnose and model the effect of DC biasing and associated impurity production at active antennas and on magnetic field connections to antennas are described. The experiments show that ICRF near-fields can lead not only to E x B convection, but also to modifications of the SOL density, which for Alcator C-Mod are limited to a narrow region near antenna. On the other hand, the SOL density distribution along with impurity sources can be tailored using local gas injection in AUG and JET-ILW with a positive effect on reduction of impurity sources. The technique of RF image current cancellation at antenna limiters was successfully applied in AUG using the 3-strap AUG antenna and extended to the 4-strap Alcator C-Mod field-aligned antenna. Multiple observations confirmed the reduction of the impact of ICRF on the SOL and on total impurity production when the ratio of the power of the central straps to the total antenna power is in the range 0.6 < P-cen / P-total < 0.8. Near-field calculations indicate that this fairly robust technique can be applied to the ITER ICRF antenna, enabling the mode of operation with reduced PWI. On the contrary, for the A2 antenna in JET-ILW the technique is hindered by RF sheaths excited at the antenna septum. Thus, in order to reduce the effect of ICRF power on PWI in a future fusion reactor, the antenna design has to be optimized along with design of plasmafacing components.
6.	Bobkov, V., et al. (författare) Progress in reducing ICRF-specific impurity release in ASDEX upgrade and JET 2017 Ingår i: Nuclear Materials and Energy. - : ELSEVIER. - 2352-1791. ; 12, s. 1194-1198 Tidskriftsartikel (refereegranskat)abstract Use of new 3-strap ICRF antennas with all-tungsten (W) limiters in ASDEX Upgrade results in a reduction of the W sources at the antenna limiters and of the W content in the confined plasma by at least a factor of 2 compared to the W-limiter 2-strap antennas used in the past. The reduction is observed with a broad range of plasma shapes. In multiple locations of antenna frame, the limiter W source has a minimum when RF image currents are decreased by cancellation of the RF current contributions of the central and the outer straps. In JET with ITER-like wall, ITER-like antenna produces about 20% less of main chamber radiation and of W content compared to the old A2 antennas. However the effect of the A2 antennas on W content is scattered depending on which antennas are powered. Experiments in JET with trace nitrogen (N-2) injection show that a presence of active ICRF antenna close to the midplane injection valve has little effect on the core N content, both in dipole and in -90 degrees phasing. This indicates that the effect of ICRF on impurity transport across the scape-off-layer is small in JET compared to the dominant effect on impurity sources leading to increased impurity levels during ICRF operation.
7.	Borodin, D., et al. (författare) Improved ERO modelling for spectroscopy of physically and chemically assisted eroded beryllium from the JET-ILW 2016 Ingår i: Nuclear Materials and Energy. - : ELSEVIER. - 2352-1791. ; 9, s. 604-609 Tidskriftsartikel (refereegranskat)abstract Physical and chemical assisted physical sputtering were characterised by the Be I and Be II line and BeD band emission in the observation chord measuring the sightline integrated emission in front of the inner beryllium limiter at the torus midplane. The 3D local transport and plasma-surface interaction Monte-Carlo modelling (ERO code [18]) is a key for the interpretation of the observations in the vicinity of the shaped solid Be limiter. The plasma parameter variation (density scan) in limiter regime has provided a useful material for the simulation benchmark. The improved background plasma parameters input, the new analytical expression for particle tracking in the sheath region and implementation of the BeD release into ERO has helped to clarify some deviations between modelling and experiments encountered in the previous studies [4,5]. Reproducing the observations provides additional confidence in our 'ERO-min' fit for the physical sputtering yields for the plasma-wetted areas based on simulated data.
8.	Borodin, D., et al. (författare) Improved ERO modelling of beryllium erosion at ITER upper first wall panel using JET-ILW and PISCES-B experience 2019 Ingår i: Nuclear Materials and Energy. - : Elsevier. - 2352-1791. ; 19, s. 510-515 Tidskriftsartikel (refereegranskat)abstract ERO is a 3D Monte-Carlo impurity transport and plasma-surface interaction code. In 2011 it was applied for the ITER first wall (FW) life time predictions [1] (critical blanket module BM11). After that the same code was significantly improved during its application to existing fusion-relevant plasma devices: the tokamak JET equipped with an ITER-like wall and linear plasma device PISCES-B. This has allowed testing the sputtering data for beryllium (Be) and showing that the "ERO-min" fit based on the large (50%) deuterium (D) surface content is well suitable for plasma-wetted areas (D plasma). The improved procedure for calculating of the effective sputtering yields for each location along the plasma-facing surface using the recently developed semi-analytical sheath approach was validated. The re-evaluation of the effective yields for BM11 following the similar revisit of the JET data has indicated significant increase of erosion and motivated the current re-visit of ERO simulations.
9.	Borodkina, I., et al. (författare) An analytical expression for ion velocities at the wall including the sheath electric field and surface biasing for erosion modeling at JET ILW 2017 Ingår i: Nuclear Materials and Energy. - : Elsevier. - 2352-1791. ; 12, s. 341-345 Tidskriftsartikel (refereegranskat)abstract For simulation of plasma-facing component erosion in fusion experiments, an analytical expression for the ion velocity just before the surface impact including the local electric field and an optional surface biasing effect is suggested. Energy and angular impact distributions and the resulting effective sputtering yields were produced for several experimental scenarios at JET ILW mostly involving PFCs exposed to an oblique magnetic field. The analytic solution has been applied as an improvement to earlier ERO modelling of localized, Be outer limiter, RF-enhanced erosion, modulated by toggling of a remote, however magnetically connected ICRH antenna. The effective W sputtering yields due to D and Be ion impact in Type-I and Type-III ELMs and inter-ELM conditions were also estimated using the analytical approach and benchmarked by spectroscopy. The intra-ELM W sputtering flux increases almost 10 times in comparison to the inter-ELM flux.
10.	Bykov, I., et al. (författare) Modification of adhered dust on plasma-facing surfaces due to exposure to ELMy H-mode plasma in DIII-D 2017 Ingår i: NUCLEAR MATERIALS AND ENERGY. - : Elsevier BV. - 2352-1791. ; 12, s. 379-385 Tidskriftsartikel (refereegranskat)abstract Transient heat load tests have been conducted in the lower divertor of DIII-D using DiMES manipulator in order to study the behavior of dust on tungsten Plasma Facing Components (PFCs) during ELMy H-mode discharges. Samples with pre- adhered, pre- characterized dust have been exposed at the outer strike point (OSP) in a series of discharges with varied intra-(inter-) ELM heat fluxes. We used C dust because of its high sublimation temperature and non-metal properties. Al dust as a surrogate for Be and W dust were employed as relevant to that in the ITER divertor. The poor initial thermal contact between the substrate and the particles led to overheating, sublimation and shrinking of the carbon dust, and wetting induced coagulation of Al dust. Little modification of the W dust was observed. An enhanced surface adhesion and improvement of the thermal contact of C and Al dust were the result of exposure. A post mortem "adhesive tape" sampling showed that 70% of Al, <5% of W and C particles could not be removed from the surface owing to the improved adhesion. Al and C but not W particles that could be lifted had W inclusions indicating damage to the substrate. This suggests that non destructive methods may be inefficient for removal of dust in ITER.
11.	Catarino, N., et al. (författare) Assessment of erosion, deposition and fuel retention in the JET-ILW divertor from ion beam analysis data 2017 Ingår i: Nuclear Materials and Energy. - : ELSEVIER. - 2352-1791. ; 12, s. 559-563 Tidskriftsartikel (refereegranskat)abstract Post-mortem analyses of individual components provide relevant information on plasma-surface interactions like tungsten erosion, beryllium deposition and plasma fuel retention with divertor tiles via implantation or co-deposition. Ion Beam techniques are ideal tools for such purposes and have been extensively used for post-mortem analyses of selected tiles from JET following each campaign. In this contribution results from tiles removed from the JET ITER-Like Wall (JET-ILW) divertor following the 2013-2014 campaign are presented. The results summarize erosion, deposition and fuel retention along the poloidal cross section of the divertor surface and provide data for comparison with the first JET-ILW campaign, showing a similar pattern of material migration with the exception of Tile 6 where the strike point time on the tile was similar to 4 times longer in 2013-2014 than in 2011-2012, which is likely to account for more material migration to this region. The W deposition on top of the Mo marker coating of Tile 4 shows that the enrichment takes place at the strike point location. (C) 2016 The Authors. Published by Elsevier Ltd.
12.	Chankina, A. V., et al. (författare) Possible influence of near SOL plasma on the H-mode power threshold 2017 Ingår i: Nuclear Materials and Energy. - : Elsevier. - 2352-1791. ; 12, s. 273-277 Tidskriftsartikel (refereegranskat)abstract A strong effect of divertor configuration on the threshold power for the L-H transition (P-LH) was observed in recent JET experiments in the new ITER-like Wall (ILW) [1-3]. Following a series of EDGE2D-EIRENE code simulations with Be impurity and drifts a possible mechanism for the P-LH variation with the divertor geometry is proposed. Both experiment and code simulations show that in the configuration with lower neutral recycling near the outer strike point (OSP), electron temperature (T-e) peaks near the OSP prior to the L-H transition, while in the configuration with higher OSP recycling T-e peaks further out in the scrape-offlayer (SOL) and the plasma stays in the L-mode at the same input power. Code results show large positive radial electric field (E-r) in the near SOL under lower recycling conditions leading to a large E x B shear across the separatrix which may trigger earlier (at lower input power) edge turbulence suppression and lower P-LH. Suppressed T-e's at OSP in configurations with strike points on vertical targets (VT) were observed earlier and explained by a geometrical effect of neutral recycling near this particular position, whereas in configurations with strike points on horizontal targets (HT) the OSP appears to be more open for neutrals (see e.g. review paper [4]).
13.	Coburn, J., et al. (författare) Reassessing energy deposition for the ITER 5 MA vertical displacement event with an improved DINA model 2021 Ingår i: Nuclear Materials and Energy. - : Elsevier BV. - 2352-1791. ; 28 Tidskriftsartikel (refereegranskat)abstract The beryllium (Be) main chamber wall interaction during a 5 MA/1.8 T upward, unmitigated VDE scenario, first analysed in [J. Coburn et al., Phys. Scr. T171 (2020) 014076] for ITER, has been re-evaluated using the latest energy deposition analysis software. Updates to the DINA disruption model are summarized, including an improved numerical convergence for the OD power balance, limitations on the safety factor within the plasma core, and the choice to maintain a constant plasma + halo poloidal cross-section. Such updates result in a broad halo region and higher radiated power fractions compared to previous models. The new scenario lasts for similar to 75 ms and deposits similar to 29 MJ of energy, with the radial distribution of parallel heat flux q parallel to(r) resembling an exponential falloff with an effective lambda(q) = 75 -198 mm. A maximum halo width w(h) of 0.52 m at the outboard midplane is observed. SMITER field line tracing and energy deposition simulations calculate a q(perpendicular to,max) of similar to 83 MW/m(2) on the upper first wall panels (FWP). Heat transfer calculations with the MEMOS-U code show that the FWP surface temperature reaches similar to 1000 K, well below the Be melt threshold. Variations of this 5 MA scenario with Be impurity densities from 0 to 3.10(19) m(-3) also remain below the melt threshold despite differences in energy deposition and duration. These results are in contrast to the early study which predicted melt damage to the first wall [J. Coburn et al., Phys. Scr. T171 (2020) 014076], and emphasize the importance of accurate models for the halo width w(h) and the heat flux distribution q parallel to(r) within that halo width. The 2020 halo model in DINA has been compared with halo current experiments on COMPASS, JET, and Alcator C-Mod, and the preliminary results build confidence in the broad halo width predictions. Results for the 5 MA VDE are compared with those for a 15 MA equivalent, generated using the new DINA model. At the higher current, significant melting of the upper FWP is to be expected.
14.	Corre, Y., et al. (författare) Testing of ITER-grade plasma facing units in the WEST tokamak: Progress in understanding heat loading and damage mechanisms 2023 Ingår i: Nuclear Materials and Energy. - : Elsevier BV. - 2352-1791. ; 37 Tidskriftsartikel (refereegranskat)abstract Assessing the performance of the ITER design for the tungsten (W) divertor Plasma Facing Units (PFUs) in a tokamak environment is a high priority issue to ensure efficient plasma operation. This paper reviews the most recent results derived from experiments and post-mortem analysis of the ITER-grade PFUs exposed in the WEST tokamak and the associated modelling, with a focus on understanding heat loading and damage evolution. Several shaping options, sharp or chamfered leading edge (LE), unshaped or shaped blocks with a toroidal bevel as foreseen in ITER, were investigated, under steady state heat fluxes of up to 120 MW⋅m−2 and 6 MW⋅m−2 on the sharp LE and top surface of the block, respectively. A very high spatial resolution (VHR) infrared (IR) camera (0.1 mm/pixel) was used to derive the temporal and surface distribution of the temperature and heat load on the castellated tungsten blocks for different geometric alignment and plasma conditions. Photonic modelling was required to reproduce the IR measurements in particular in the toroidal and poloidal gaps of the mono-block (MB) stacks where high apparent temperatures are observed. Specular reflection is found to be the dominant emitter in these parts of the blocks. W-cracking was observed on the leading edge of the blocks already within the first phase of plasma operation, during which the divertor was equipped with unshaped PFUs, including some intentionally misaligned blocks. Numerical analysis taking into account softening processes and mechanical stresses, revealed brittle failure due to transients as the dominant failure mechanisms. Ductile failure was observed in one particular block used for the melting experiment, therefore under extremely high steady state heat load conditions. W-melting achieved on actively cooled PFU exhibits specific features: shallow melting and slow melt displacement. Plasma exposure of pre-damaged PFUs at various damage levels (crack network and melted droplets) was carried out under high heat load conditions with several hours of cumulated plasma duration. IR data and preliminary surface analyses show no evidence of significant degradation damage progression under these conditions.
15.	Cupak, C., et al. (författare) Absence of synergistic effects in quasi-simultaneous sputtering of tungsten by Ar and D ions 2023 Ingår i: Nuclear Materials and Energy. - : Elsevier. - 2352-1791. ; 35 Tidskriftsartikel (refereegranskat)abstract A quartz crystal microbalance was used to experimentally study the erosion of tungsten during rapidly alternating bombardment with 2 keV argon and deuterium projectiles. A key goal was to investigate whether the mean sputtering yield of the alternating irradiation can be predicted from data for sputtering yields of single ion species. In addition, influences by residual gas pressure in the UHV experiment and variable ion fluxes have been studied. Our results show that the mean sputtering yield of irradiations with alternating ion species can be well predicted for a range of different fluence ratios as a simple superposition of individual sputtering yields, weighted by the respective relative fluences. This finding supports that no synergistic sputtering effects were relevant in the investigated low-flux regime.
16.	Cupak, C., et al. (författare) Retention of deuterium in beryllium : A combined investigation using TDS, ERDA and EBS 2022 Ingår i: Nuclear Materials and Energy. - : Elsevier. - 2352-1791. ; 33 Tidskriftsartikel (refereegranskat)abstract We have studied the retention of deuterium in beryllium, implanted with an energy of 500 eV/D, using a combination of thermal desorption spectroscopy, elastic recoil detection analysis and elastic backscattering spectroscopy. The parallel use of these techniques allowed us to directly quantify the absolute deuterium content reduction of the sample for specific desorption peaks observed during thermal annealing. In addition, the presence of a beryllium oxide surface layer was observed, despite sputter-cleaning of the sample was initially conducted in-situ. A main result was that similar to 85 % of the retained deuterium got released during the primary desorption peak at 400 K. A smaller, secondary desorption peak was identified at 540 K. All deuterium could be removed from the Be sample by heating it to a temperature of 800 K.
17.	De Angeli, M., et al. (författare) Cross machine investigation of magnetic tokamak dust; structural and magnetic analysis 2021 Ingår i: Nuclear Materials and Energy. - : Elsevier BV. - 2352-1791. ; 28 Tidskriftsartikel (refereegranskat)abstract Magnetic dust collected from multiple fusion devices (FTU, Alcator C-Mod, COMPASS) that feature different plasma-facing components (PFCs) and toroidal magnetic fields has been analyzed by means of the X-ray diffraction technique aiming to investigate the nature and origin of dust magnetism. Analysis led to the conclusion that the main mechanism of ferromagnetic dust formation is the change of iron crystalline phase from austenitic to ferritic during the re-solidification of stainless steel droplets. Analysis also revealed differences in the collected dust structure and an unexpectedly high amount of stainless steel based dust in its native austenitic phase. Theoretical estimates showed that the magnetic moment force can also mobilize strongly paramagnetic adhered dust prior to the establishment of proper tokamak discharges. The post-mortem analysis of dust collected during pure magnetic discharges in FTU confirmed these estimates.
18.	De Angeli, M., et al. (författare) Post-mortem and in-situ investigations of magnetic dust in ASDEX Upgrade 2023 Ingår i: Nuclear Materials and Energy. - : Elsevier BV. - 2352-1791. ; 36 Tidskriftsartikel (refereegranskat)abstract Pre-plasma mobilization of magnetic dust can be an important issue for future fusion reactors where plasma breakdown is critical. A combined on-line and off-line study of magnetic dust in ASDEX Upgrade is reported. Post-mortem collection revealed similar composition and morphology compared to other tokamaks, but the overall amount was much smaller. Optical and IR camera diagnostics excluded dust flybys prior to plasma start-up. The negative detection is discussed in light of the magnetic dust properties, the strength of mobilizing forces and the temporal evolution of the magnetic field.
19.	De Angeli, M., et al. (författare) Remobilization of tungsten dust from castellated plasma-facing components 2017 Ingår i: NUCLEAR MATERIALS AND ENERGY. - : Elsevier BV. - 2352-1791. ; 12, s. 536-540 Tidskriftsartikel (refereegranskat)abstract Studies of tungsten dust remobilization from castellated plasma-facing components can shed light to whether gaps constitute a dust accumulation site with important implications for monitoring but also removal. Castellated structures of ITER relevant geometry that contained pre-adhered tungsten dust of controlled deposition profile have been exposed in the Pilot-PSI linear device. The experiments were performed under steady state and transient plasma conditions, as well as varying magnetic field topologies. The results suggest that dust remobilization from the plasma-facing monoblock surface can enhance dust trapping in the gaps and that tungsten dust is efficiently trapped inside the gaps.
20.	De Temmerman, Gregory, et al. (författare) Data on erosion and hydrogen fuel retention in Beryllium plasma-facing materials 2021 Ingår i: Nuclear Materials and Energy. - : Elsevier BV. - 2352-1791. ; 27 Tidskriftsartikel (refereegranskat)abstract ITER will use beryllium as a plasma-facing material in the main chamber, covering a total surface area of about 620 m(2). Given the importance of beryllium erosion and co-deposition for tritium retention in ITER, significant efforts have been made to understand the behaviour of beryllium under fusion-relevant conditions with high particle and heat loads. This paper provides a comprehensive report on the state of knowledge of beryllium behaviour under fusion-relevant conditions: the erosion mechanisms and their consequences, beryllium migration in JET, fuel retention and dust generation. The paper reviews basic laboratory studies, advanced computer simulations and experience from laboratory plasma experiments in linear simulators of plasma-wall interactions and in controlled fusion devices using beryllium plasma-facing components. A critical assessment of analytical methods and simulation codes used in beryllium studies is given. The overall objective is to review the existing set of data with a broad literature survey and to identify gaps and research needs to broaden the database for ITER.
21.	Denis, J., et al. (författare) Dynamic modelling of local fuel inventory and desorption in the whole tokamak vacuum vessel for auto-consistent plasma-wall interaction simulations 2019 Ingår i: Nuclear Materials and Energy. - : Elsevier. - 2352-1791. ; 19, s. 550-557 Tidskriftsartikel (refereegranskat)abstract An extension of the SolEdge2D-EIRENE code package, named D-WEE, has been developed to add the dynamics of thermal desorption of hydrogen isotopes from the surface of plasma facing materials. To achieve this purpose, D-WEE models hydrogen isotopes implantation, transport and retention in those materials. Before launching autoconsistent simulation (with feedback of D-WEE on SolEdge2D-EIRENE), D-WEE has to be initialised to ensure a realistic wall behaviour in terms of dynamics (pumping or fuelling areas) and fuel content. A methodology based on modelling is introduced to perform such initialisation. A synthetic plasma pulse is built from consecutive SolEdge2D-EIRENE simulations. This synthetic pulse is used as a plasma background for the D-WEE module. A sequence of plasma pulses is simulated with D-WEE to model a tokamak operation. This simulation enables to extract at a desired time during a pulse the local fuel inventory and the local desorption flux density which could be used as initial condition for coupled plasma-wall simulations. To assess the relevance of the dynamic retention behaviour obtained in the simulation, a confrontation to post-pulse experimental pressure measurement is performed. Such confrontation reveals a qualitative agreement between the temporal pressure drop obtained in the simulation and the one observed experimentally. The simulated dynamic retention during the consecutive pulses is also studied.
22.	Dittrich, Laura, et al. (författare) Impact of ion irradiation and film deposition on optical and fuel retention properties of Mo polycrystalline and single crystal mirrors 2023 Ingår i: Nuclear Materials and Energy. - : Elsevier BV. - 2352-1791. ; 37 Tidskriftsartikel (refereegranskat)abstract Polycrystalline (PC) and single crystal (SC) molybdenum mirrors were irradiated with 98Mo+, 1H+, 4He+, 11B+ and 184W+. Energies were chosen to impact the optically active region (up to 30 nm deep) of Mo mirrors. Some surfaces were coated by magnetron sputtering either with B or W films 4–65 nm thick. The overall objective was to simulate the neutron-induced damage and transmutation (H, He), and the impact of H, He, B, W on the optical performance of test mirrors, and on fuel retention. In parallel, a set of PC Mo mirrors irradiated with 1.6 MeV 98Mo3+ to a damage of 2 dpa and 20 dpa was installed in the JET tokamak for exposure during deuterium-tritium campaigns. Data from spectrophotometric, ion beam and microscopy techniques reveal: (i) the irradiation decreased specular reflectivity, whereby the differences between PC and SC in reflectivity are very small, (ii) He is retained in bubbles within 25–30 nm of the subsurface layer in all irradiated materials, (iii) W, either deposited or implanted, decreases reflectivity, but the strongest reflectivity degradation is caused by B deposition. Laboratory studies show the correlation of damage and H retention. Several cycles of W deposition and its removal from SC-Mo mirrors by plasma-assisted methods were also performed.
23.	Eich, T., et al. (författare) ELM divertor peak energy fluence scaling to ITER with data from JET, MAST and ASDEX upgrade 2017 Ingår i: Nuclear Materials and Energy. - : Elsevier. - 2352-1791. ; 12, s. 84-90 Tidskriftsartikel (refereegranskat)abstract A newly established scaling of the ELM energy fluence using dedicated data sets from JET operation with CFC & ILW plasma facing components (PFCs), ASDEX Upgrade (AUG) operation with both CFC and full-W PFCs and MAST with CFC walls has been generated. The scaling reveals an approximately linear dependence of the peak ELM energy with the pedestal top electron pressure and with the minor radius; a square root dependence is seen on the relative ELM loss energy. The result of this scaling gives a range in parallel peak ELM energy fluence of 10-30 MJm(-2) for ITER Q = 10 operation and 2.5-7.5 MJm(-2) for intermediate ITER operation at 7.5 MA and 2.65 T. These latter numbers are calculated using a numerical regression (epsilon(II) = 0.28 MJ/m(2) n(e)(0.75) T-e(1) Delta E-ELM(0.5) R-1(geo)). A simple model for ELM induced thermal load is introduced, resulting in an expression for the ELM energy fluence of epsilon(II) congruent to 6 pi p(e) R-geo q(edge). The relative ELM loss energy in the data is between 2-10% and the ELM energy fluence varies within a range of 10(0.5) similar to 3 consistently for each individual device. The so far analysed power load database for ELM mitigation experiments from JET-EFCC and Kicks, MAST-RMP and AUG-RMP operation are found to be consistent with both the scaling and the introduced model, ie not showing a further reduction with respect to their pedestal pressure. The extrapolated ELM energy fluencies are compared to material limits in ITER and found to be of concern.
24.	Fellinger, Joris, et al. (författare) Tungsten based divertor development for Wendelstein 7-X 2023 Ingår i: Nuclear Materials and Energy. - 2352-1791. ; 37 Tidskriftsartikel (refereegranskat)abstract Wendelstein 7-X, the worldâ€™s largest superconducting stellarator in Greifswald (Germany), started plasma experiments with a water-cooled plasma-facing wall in 2022, allowing for long pulse operation. In parallel, a project was launched in 2021 to develop a W based divertor, replacing the current CFC divertor, to demonstrate plasma performance of a stellarator with a reactor relevant plasma facing materials with low tritium retention. The project consists of two tasks: Based on experience from the previous experimental campaigns and improved physics modelling, the geometry of the plasma-facing surface of the divertor and baffles is optimized to prevent overloads and to improve exhaust. In parallel, the manufacturing technology for a W based target module is qualified. This paper gives a status update of project. It focusses on the conceptual design of a W based target module, the manufacturing technology and its qualification, which is conducted in the framework of the EUROfusion funded WPDIV program. A flat tile design in which a target module is made of a single target element is pursued. The technology must allow for moderate curvatures of the plasma-facing surface to follow the magnetic field lines. The target element is designed for steady state heat loads of 10Â MW/m2 (as for the CFC divertor). Target modules of a similar size and weight as for the CFC divertor are assumed (approx.Â <Â 0.25Â m2 andÂ <Â 60Â kg) using the existing water cooling infrastructure providing 5Â l/s and roughly maximum 15Â bar pressure drop per module. The main technology under qualification is based on a CuCrZr heat sink made either by additive manufacturing using laser powder bed fusion (LPBF) or by uniaxial diffusion welding of pre-machined forged CuCrZr plates. After heat treatment, the plasma-facing side of the heat sink is covered by W or if feasible by the more ductile WNiFe, preferably by coating or alternatively by hot isostatic pressing W based tiles with a soft OFE-Cu interlayer. Last step is a final machining of the plasma-exposed surface and the interfaces to the water supply lines and supports to correct manufacturing deformations.
25.	Fortuna-Zalesna, E., et al. (författare) Studies of dust from JET with the ITER-Like Wall : Composition and internal structure 2017 Ingår i: Nuclear Materials and Energy. - : ELSEVIER. - 2352-1791. ; 12, s. 582-587 Tidskriftsartikel (refereegranskat)abstract Results are presented for the dust survey performed at JET after the second experimental campaign with the ITER-Like Wall: 2013-2014. Samples were collected on adhesive stickers from several different positions in the divertor both on the tiles and on the divertor carrier. Brittle dust-forming deposits on test mirrors from the inner divertor wall were also studied. Comprehensive characterization accomplished by a wide range of high-resolution microscopy techniques, including focused ion beam, has led to the identification of several classes of particles: (i) beryllium flakes originating either from the Be coatings from the inner wall cladding or Be-rich mixed co-deposits resulting from material migration; (ii) beryllium droplets and splashes; (iii) tungsten and nickel-rich (from Inconel) droplets; (iv) mixed material layers with a various content of small (8-200 nm) W-Mo and Ni-based debris. A significant content of nitrogen from plasma edge cooling has been identified in all types of co-deposits. A comparison between particles collected after the first and second experimental campaign is also presented and discussed. (C) 2016 Published by Elsevier Ltd. This is an open access article under the CC BY-NC-ND license.

Skapa referenser, mejla, bekava och länka

Länka till träfflistan

Träfflista för sökning "L773:2352 1791 "

Avgränsa träffmängd

År