| 21. |
- Shoja, Siamak, 1980
(författare)
-
Microstructure and plastic deformation of textured CVD alumina coatings
- 2020
-
Licentiatavhandling (övrigt vetenskapligt/konstnärligt)abstract
- It is known that the wear performance of α-alumina coatings produced by chemical vapor deposition (CVD) is significantly influenced by the type and degree of texture. However, the main reasons behind this behavior are not fully understood. This thesis contains studies of two related topics for increasing the understanding of α-alumina coatings. The first topic concerns the microstructure and texture development of CVD α-Al2O3 coatings, and the second topic concerns calculations and analysis of the Schmid factors ( m ) for coatings with different textures. By combining different analysis methods (such as XRD, SEM, FIB/SEM, TKD, TEM, STEM, XEDS), and theoretical and experimental Schmid factor analysis by MATLAB and EBSD, the microstructure and plastic deformation of α-alumina coatings were investigated. The microstructures of three different CVD α-Al2O3 layers deposited onto a Ti(C,N,O) bonding layer were studied. Grain boundary diffusion of heavy elements from the substrate to the bonding layer/α-Al2O3 interface was observed. This may be the cause of a disturbance in the early growth of α-Al2O3. Additionally, it was found that the number of interfacial pores at the bonding layer/α-Al2O3 interface increased by introducing the H2S gas. The H2S gas also promoted an earlier development of the (0001) texture. The orientation of the grains was developed to the desired texture both as a gradual change over several grains and as an abrupt transformation from one grain to another. The probability of plastic deformation in different wear zones on the rake face of a cutting tool was investigated theoretically and experimentally by analyzing Schmid factors for textured α-Al2O3 coatings. Schmid factor diagrams were constructed using MATLAB/MTEX and used to extract frequency distributions for different slip systems and textures. The results were compared with lateral distribution maps of Schmid factors obtained from experimental coatings. It was observed that basal slip is most easily activated in the transition zone, followed by prismatic slip systems 1 and 2 in coatings with an (0001)-texture. The homogeneous plastic deformation behavior observed in this coating is also connected to mostly high Schmid factors in the m -value distribution. The differences between the m -value distributions for the three slip systems are not that pronounced in the (01-12) and (11-20) textures, and the distributions are relatively wide. The low wear rate and more homogeneous deformation of the coating with (0001) texture compared to the other coating textures may be the result of the high plasticity, offered by the easy activation of basal slip and prismatic 1 slip, and the low spread of Schmid factor values at the transition zone. In conclusion, the results presented in this thesis form a knowledge platform that can be used to understand the microstructure and wear mechanisms of textured CVD α-alumina coatings.
|
|
| 22. |
- André, Alann, et al.
(författare)
-
Finite element delamination study of a notched composite plate under flexural loads
- 2009
-
Ingår i: ICCM-17, 17th International Conference on Composite Materials, Edinburgh, UK. - London : IOM Communications.
-
Konferensbidrag (refereegranskat)abstract
- The delamination process in notched composite plates under flexural loading has been investigated using finite element analysis. Cohesive elements implemented in the commercial finite element package ABAQUS have been used in the region around the drilled-hole, and positioned between layers where delamination was observed during experiments presented in an accompanying paper. The delamination initiation and subsequent propagation was studied between the layers at the tension side separately and simultaneously. For all FE models, the load displacement curve was in good agreement with the one from experiments. However, the amount of damage reported from the fractography study was more extensive than that predicted by the models. Finally, it was shown that the models with only one cohesive layer show significantly different results to that of the model with four cohesive layers in terms of size of the degradation area.
|
|
| 23. |
|
|
| 24. |
- André, Benny
(författare)
-
Nanocomposites for Use in Sliding Electrical Contacts
- 2011
-
Doktorsavhandling (övrigt vetenskapligt/konstnärligt)abstract
- In this thesis nanocomposite materials for use in high performance electrical contacts are tested. Self mating silver as coatings on cupper substrates are the most used material combination in power connectors today. In this work two new concepts were tested. The first one was to change one of the mating surfaces to a hard thin coating and keep the other surface made of silver. Tested coatings were nanocomposites with hard carbides in a matrix of amorphous carbon. TiC/a-C and Ti-Ni-C/a-C were tested both electrically and tribologically. The total amount of carbon and the amount of carbon matrix was important, both for the electrical and the tribological properties. The Ti-Ni-C coating also showed that substituting Ti in TiC with the weak carbide former Ni changed the stability of the carbides. The substitution resulted in more a-C matrix and less C in the carbides. Thin coatings of nc-TiC/a-C and Ti-Ni-C/a-C showed high potential as material candidates for use in electrical contacts. The other tested concept was to modify the used silver instead of replacing it. This was done by embedding nanoparticles of solid lubricant IF-WS2 in the silver. The results from reciprocating sliding displayed low friction and high wear resistance. The modified silver surfaces lasted for 8000 strokes with a friction of about 0.3 while at the same time allowing for a low contact resistance. The results for surfaces of pure silver coating displayed a friction of 0.8-1.2 and that the silver was worn through already after 300 strokes. A new method to investigate inherent hardness and residual stress of thin coatings, on complex geometries or in small areas, was also developed. An ion beam was used to create stress free coating as free standing micro pillars. Hardness measured on the pillars and on as-deposited coating were then used to calculate the residual stress in the coatings.
|
|
| 25. |
- Cho, Sung-Woo, et al.
(författare)
-
Injection-molded nanocomposites and materials based on wheat gluten
- 2011
-
Ingår i: International Journal of Biological Macromolecules. - : Elsevier BV. - 0141-8130 .- 1879-0003. ; 48:1, s. 146-152
-
Tidskriftsartikel (refereegranskat)abstract
- This is, to our knowledge, the first study of the injection molding of materials where wheat gluten (WG) is the main component. In addition to a plasticizer (glycerol), 5 wt.% natural montmorillonite clay was added. X-ray indicated intercalated clay and transmission electron microscopy indicated locally good clay platelet dispersion. Prior to feeding into the injection molder, the material was first compression molded into plates and pelletized. The filling of the circular mold via the central gate was characterized by a divergent flow yielding, in general, a stronger and stiffer material in the circumferential direction. It was observed that 20–30 wt.% glycerol yielded the best combination of processability and mechanical properties. The clay yielded improved processability, plate homogeneity and tensile stiffness. IR spectroscopy and protein solubility indicated that the injection molding process yielded a highly aggregated structure. The overall conclusion was that injection molding is a very promising method for producing WG objects.
|
|
| 26. |
- He, Wenxiao, 1985
(författare)
-
Biomimetic Formation of Calcium Phosphate Based Nanomaterials
- 2014
-
Doktorsavhandling (övrigt vetenskapligt/konstnärligt)abstract
- The intercellular material in bone is a nanocomposite of aligned “hard” inorganics—calcium phosphate (CaP) platelets embedded in the long-range ordered “soft” organic collagen matrix. This elaborate structural arrangement redeems the weaknesses of the individual components (being soft protein or brittle mineral) and gives bone its excellent mechanical properties for the protection and support of our bodies. The structural order and hierarchy in the soft matrix is organized via self-assembly of collagen molecules and is reinforced by intermolecular crosslinking. The subsequent growth of “hard” crystallites inside the “soft” matrix compartments, likely through the deposition of a transient amorphous calcium phosphate (ACP) phase, results in the interpenetrated composite structure.The aim of this thesis was to prepare synthetic mimetics of “hard” material (CaP) with well-defined nanostructures, soft organic matrices with long-range order and interpenetrated composites composing of the two. The work was inspired by the material deposition process in natural bone. Lyotropic liquid crystal (LC) phases self-assembled by block copolymers were used to mimic the structural order of the collagen matrix. Both the inorganic morphogenesis of CaP in LCs and the controlled crystallization of ACP were investigated. To explore ordered organic matrices, crosslinking of the LCs and the self-assembly of an amphiphilic peptide with designed sequence were performed. In addition, controlled mineralization within crosslinked LCs was examined for the formation of nanocomposites.ACP nanospheres, CaP nanowires and nanosheets were prepared from LCs via templated growth. The ACP nanospheres were capable of transforming into bone-like apatite by controlled aging in water and the prepared nanoparticles were shown to affect osteoblast gene expression. Dicalcium phosphate crystals (brushite and monetite) with structural hierarchy and distinct features were also grown in LCs through epitaxial overgrowth or a self-organization regime. Polymerized LCs were successfully prepared from a modified block copolymer (diacrylate derivative of Pluronic® F127), which served as a resilient matrix for the deposition of ACP nanospheres. A subsequent in situ crystallization of ACP into bone-like apatite resulted in mechanically stable composites retaining nanostructures that resembled that of natural bone. An amphiphilic peptide was designed using mainly natural amino acids and it was shown to self-assemble into distinct structures at different concentrations. Based upon the results presented in this thesis, nanomaterials with assorted structures can be further designed for bio-related applications.
|
|
| 27. |
- Johansen, Marcus, 1994
(författare)
-
Atoms in Lithiated Carbon Fibres
- 2023
-
Doktorsavhandling (övrigt vetenskapligt/konstnärligt)abstract
- Carbon fibres are key constituents of structural batteries, in which electrochemical energy storage and mechanical load bearing are merged in one multifunctional device. Here carbon fibres simultaneously act as structural reinforcement by carrying load and as battery electrode by hosting lithium (Li)-ions in its microstructure. However, conventional carbon fibres are not designed to be multifunctional. To enable carbon fibres with optimised multifunctional capabilities, a fundamental understanding of their microstructure, chemical information and interaction with Li is required. In this thesis, mass spectrometry and electron spectroscopy techniques are developed and used to elucidate the atomic distribution, configuration, and interaction in commercial carbon fibres used in structural batteries. Here the methodology of analysing Li in carbon fibres with atom probe tomography (APT) and Auger electron spectroscopy (AES) is demonstrated. Synchrotron-based hard X-ray photoelectron spectroscopy (HAXPES) reveals that certain chemical states of N heteroatoms, pyridinic and pyrrolic, are connected to enhanced electrochemical performance of carbon fibres. AES shows that: Li distributes throughout the entire carbon fibre; the amount of trapped Li is higher and concentrated towards the centre of the fibre at increased discharge rates; Li is initially inserted in amorphous domains and with increased states of lithiation in crystalline domains; and Li plating can occur on individual fibres without spreading to adjacent fibres. APT on lithiated carbon fibres shows that: the distribution of Li is independent of the distribution of N heteroatoms; trapped Li is distributed uniformly in all domains; and Li agglomerates at elevated states of lithiation. The work presented in this thesis paves the way for analysis of carbon-based battery materials with APT and AES. Furthermore, the work unveils much of the interplay between carbon fibre and Li and deepens the understanding of the design parameters for tailoring multifunctional carbon fibres used in improved structural batteries.
|
|
| 28. |
|
|
| 29. |
- Nikas, Dimitrios, 1984, et al.
(författare)
-
High temperature bi-axial low cycle fatigue behaviour of railway wheel steel
- 2019
-
Ingår i: ICMFF12 - 12TH INTERNATIONAL CONFERENCE ON MULTIAXIAL FATIGUE AND FRACTURE. - : EDP Sciences. - 2261-236X. ; 300
-
Konferensbidrag (refereegranskat)abstract
- One of the most important aspects in railway operation is the interaction between rail and wheel. Railway wheels are commonly made from medium carbon steels (similar to 0.55 wt.% C), heat treated to a near pearlitic microstructure with some 5-10% pro-eutectoid ferrite. During the operation of freight trains, where block brakes are used, high thermal loads are evolved because of recurring braking and occasional slippage. Thus the combination of mechanical and thermal loads leads to changes in the mechanical properties of the material. The focus of the current investigation is to evaluate the mechanical behaviour of wheel material (UIC ER7T) subjected to non-proportional biaxial fatigue loading, as this simulates the actual working conditions in a better way than uniaxial loading. Axial-torsional low cycle fatigue tests were performed at room temperature and elevated temperatures using thin walled specimens to study the cyclic stress-strain properties of this material. The results showed large influence of temperature on the ratcheting behaviour of the material. Biaxial non-proportional loading gave much higher strain hardening as compared to uniaxial loading. Hardening due to dynamic strain ageing can be seen in the biaxial tests at temperatures around 300 degrees C.
|
|
| 30. |
- Persson, Henrik, 1983, et al.
(författare)
-
A simple way of improving graphite nanoplatelets (GNP) for their incorporation into a polymer matrix
- 2012
-
Ingår i: Express Polymer Letters. - : Department of Polymer Engineering, Scientific Society of Mechanical Engineering. - 1788-618X. ; 6:2, s. 142-147
-
Tidskriftsartikel (refereegranskat)abstract
- A simple method of solvent exfoliation/refining of direct-graphite nanoplatelets for their better incorporation into a polymer matrix is presented. We demonstrate the method for polystyrene. The method relies on sonication in N-methyl-2-pyrrolidone solvent, with surfactant assistance. A small amount of polystyrene is added to the solvent in order to increase the viscosity, this enhancing the exfoliation process and resulting in formation of a polymeric layer on graphene for its better incorporation in the polymer matrix. Polystyrene-coated thin graphene stacks form a stable dispersion, while thicker graphite nanoplatelets settle out. Thus bulk separation of thin and thick graphene stacks takes place.The polystyrene-coated thin graphene stacks are studied using Transmission Electron Microscopy in two ways: (i) we calculate the number of graphene layers forming thin graphene stacks, and (ii) we employ Selected Area Diffraction to confirm our image analysis results by checking the intensity ratio (1100) and (2100) deflections in the diffraction patterns. Five layers is found to be the cut-off number, that is there are no stacks >5 layers, and 3 layer stacks are dominantly present. The average largest in-plane dimension is found to be approximately 2.5 mu m (reduction by 50%).
|
|
