| 1. |
|
|
| 2. |
- Sauer, Christopher, 1993
(författare)
-
Green Aromatics: Catalytic Valorisation of bio-derived 2,5-dimethylfuran over Zeolites and Zeotypes
- 2022
-
Doktorsavhandling (övrigt vetenskapligt/konstnärligt)abstract
- This thesis discusses the use of biomass as a potentially green feedstock for the chemical industry in the urgent shift away from fossil resources. I elaborate on reasons why we cannot afford to burn virgin biomass for energy production, among them a variety of ecosystem services that forests and other lands provide. In addition, the utilisation of biomass should be focused on products that sequester and lock away carbon for more extended periods, e.g. timber, materials and chemicals. In particular, biomass can be used as an alternative "carbon neutral" feedstock for the chemical industry, where we can preserve the already existing chemical complexity in the bio-based molecules. One example is the upgrading of furans to benzene, toluene and xylene (BTX) aromatics with the help of zeolite catalysis. These aromatics are important commodity chemicals, where the shift to a bio-based resource could make use of already existing knowledge, catalyst and production infrastructure. However, research is necessary to understand these new feedstock molecules and their interaction with the catalysts and to enable the design of applicable catalysts. In order to study the interaction of the furans, in particular 2,5-dimethylfuran (2,5-dmf), I describe and discuss the development of an analytical methodology that utilises infrared spectroscopy and mass spectrometry for the on-line identification and quantification of product molecules during catalytic reactions. This on-line analysis method is then applied to the catalytic conversion of 2,5-dmf to aromatics over a range of zeolite and zeotype catalysts. In-depth studies with ammonia as a probe molecule of the catalytic active acid sites, as well as temperature programmed experiments with ammonia and 2,5-dmf give insights into product distribution, selectivity changes and deactivation of the catalyst. For example, olefins and aromatics are initially preferred products, while with increasing time on stream, the isomerisation of 2,5-dmf becomes dominant. The incorporation of Ga into the zeotype framework, resulting in a Ga-Silicate, shows how targeted catalyst design can increase overall aromatics production. This catalyst is also suitable for selective isomerisation of 2,5-dmf to 2,4-dimethylfuran, which has a rare substitution pattern. Finally, itwas found that the most valuable of BTX, p -xylene, can be produced more selectively when 2,5-dmf is pre-adsorbed onto zeolite ZSM-5 and then released during a temperature programmed product desorption.
|
|
| 3. |
|
|
| 4. |
- Shwan, Soran, 1984
(författare)
-
Metal-exchanged zeolites for NH3-SCR applications - Activity and Deactivation studies
- 2014
-
Doktorsavhandling (övrigt vetenskapligt/konstnärligt)abstract
- Emissions of nitrogen oxides (NOX) formed during the burning process in internal combustion engines is a major contributor to global air pollutions. One effective way to reduce NOX in lean environments, i.e. oxygen excess is selective catalytic reduction with ammonia (NH3-SCR). Metal-exchanged zeolites have proven to be active as SCR catalysts, where copper and iron are the most common metals. When using metal-exchanged zeolites in exhaust aftertreatment systems, several challenges arise. Resistance towards hydrothermal deactivation and chemisorption of impurities on the active sites of the catalyst are two of the more important challenges. Temperatures between 600-700oC can be seen during regeneration of the particulate filter, which usually is placed upstream close to the SCR catalyst in the exhaust aftertreatment system, and therefore hydrothermal stability of the metal-exchanged zeolite is crucial. Furthermore, high tolerance against catalyst poisons which originate from (bio-) fuels and lubricating oils is desired, where phosphorous and potassium are among the more important poisons. In this thesis thermal and chemical deactivation of iron-exchanged zeolite BEA as SCR catalyst is experimentally studied with special focus paid on the active iron species. Based on the experimental results a kinetic model is developed to predict the decreased activity of the catalyst after deactivation. Several characterization techniques are used to evaluate and correlate structural changes in the catalyst with the decreased activity. Catalysts are prepared and characterized using BET, XPS, XRD, TPD, in-situ FTIR and UV-Vis. The catalytic performance of the samples is measured using a flow-reactor system.It is concluded that the hydrothermal deactivation of Fe-BEA is a result of migration of isolated iron species forming iron cluster inside the zeolite pores and iron particles located on the external surface of the zeolite crystals. Further, it is shown that the growth of iron clusters and particles can be partially reversed by high temperature hydrogen treatment. The chemical deactivation due to phosphorous exposure is the result of formation of metaphosphates replacing hydroxyl groups on the active isolated iron species. Furthermore, the chemical deactivation of Fe-BEA by potassium is concluded to be due to exchange and loss of active isolated iron species in the zeolite forming smaller iron clusters inside the zeolite pores.A kinetic model where different iron species are included was developed based on the hydrothermal deactivation experiments and validated using phosphorous and potassium exposed samples. By fitting and fix the kinetic parameters towards a fresh sample, the decreased SCR activity can be predicted by just decreasing the number of active iron sites, representing loss of active iron species due to hydrothermal treatment and poisoning.The effect of gas atmosphere during solid-state ion-exchange of copper-zeolites was studied as well. It is concluded that copper becomes highly mobile due to formation of copper-ammine complexes in presence of NH3 after reduction of CuII to CuI by adding NO in the exposing gas during the solid-state ion-exchange. Copper-exchanged zeolites could be prepared by exposing physical mixtures of copper-oxides with zeolites to NO and NH3 at as low temperature as 250oC.Finally, the ammonia formation during the rich period of NOX storage and reduction (NSR) cycles was studied using kinetic modeling for the possibility of combining NSR and SCR catalysts in the exhaust aftertreatment system. It is concluded that the formation of ammonia is due to stored NOX and hydrogen from the gas in the first half of the catalyst. However, it was further concluded that the formation of ammonia is delayed due to formation of N2O from stored NOX and formed NH3.
|
|
| 5. |
|
|
| 6. |
- Hassellöv, Martin, 1970, et al.
(författare)
-
REACH missar nano!
- 2009
-
Ingår i: Miljöforskning. ; 2009:3-4
-
Tidskriftsartikel (övrigt vetenskapligt/konstnärligt)
|
|
| 7. |
- Maurina Morais, Eduardo, 1989
(författare)
-
Synthesis of protic ionic liquids. Challenges and solutions for the synthesis of pure compounds.
- 2022
-
Licentiatavhandling (övrigt vetenskapligt/konstnärligt)abstract
- The urgent need to diversify our energy matrix is responsible for a renewed interest in fuel cell technology, which can use hydrogen gas, a renewable green fuel, as an energy source. This technology is currently a commercially available option, however, it still requires technological improvements before it can be widely used for different applications. One way this technology could potentially be improved is by increasing its temperature range of operation by developing new, anhydrous proton conducting materials. Protic ionic liquids, which are organic salts with low melting temperatures, are interesting candidates for this application, since they can conduct protons in the operational conditions of fuel cells and without the need of water. These compounds can be synthesized by a simple acid-base neutralization reaction, but certain considerations must be taken in order to obtain high quality (dry and pure) protic ionic liquids. In this thesis, a series of triazolium and imidazolium based protic ionic liquids were synthesized using a solvent-free method designed to address several limitations encountered with other commonly used methods. Using this method, pure (98-99% m/m) and dry (128-553 ppm of water) protic ionic liquids were synthesized (in a laboratory scale) without the need for purification methods that require heating the ionic liquid, hence avoiding the common issue of thermal decomposition. This method was also designed to allow for the accurate measurement of acid and base, and for the controlled mixing of both compounds, which is essential to avoid producing impure protic ionic liquids with excess of either acid or base. The system is consists of only glass and chemically resistant polymer(PTFE and PVDF) parts, which avoids other contaminants that can result from unwanted reactions involving the reagents with common laboratory tools (metallic objects, paper, plastic, etc.). The resulting ionic liquids were carefully analyzed by spectroscopic and thermal analysis methods designed to avoid water absorption, which is known to affect their properties. To complement this experimental characterization, computational chemistry tools were used to assess the ionic liquids’ properties, as well as to assign vibrational modes.
|
|
| 8. |
- Halldin Stenlid, Joakim, 1987-
(författare)
-
Computational Studies of Chemical Interactions: Molecules, Surfaces and Copper Corrosion
- 2017
-
Doktorsavhandling (övrigt vetenskapligt/konstnärligt)abstract
- The chemical bond – a corner stone in science and a prerequisite for life – is the focus of this thesis. Fundamental and applied aspects of chemical bonding are covered including the development of new computational methods for the characterization and rationalization of chemical interactions. The thesis also covers the study of corrosion of copper-based materials. The latter is motivated by the proposed use of copper as encapsulating material for spent nuclear fuel in Sweden.In close collaboration with experimental groups, state-of-the-art computational methods were employed for the study of chemistry at the atomic scale. First, oxidation of nanoparticulate copper was examined in anoxic aqueous media in order to better understand the copper-water thermodynamics in relation to the corrosion of copper material under oxygen free conditions. With a similar ambition, the water-cuprite interface was investigated with regards to its chemical composition and reactivity. This was compared to the behavior of methanol and hydrogen sulfide at the cuprite surface.An overall ambition during the development of computational methods for the analysis of chemical bonding was to bridge the gap between molecular and materials chemistry. Theory and results are thus presented and applied in both a molecular and a solid-state framework. A new property, the local electron attachment energy, for the characterization of a compound’s local electrophilicity was introduced. Together with the surface electrostatic potential, the new property predicts and rationalizes regioselectivity and trends of molecular reactions, and interactions on metal and oxide nanoparticles and extended surfaces.Detailed atomistic understanding of chemical processes is a prerequisite for the efficient development of chemistry. We therefore envisage that the results of this thesis will find widespread use in areas such as heterogeneous catalysis, drug discovery, and nanotechnology.
|
|
| 9. |
|
|
| 10. |
|
|
