| 1. |
- Burström, Lage, 1954-, et al.
(författare)
-
Vibrotactile perception and effects of short-term exposure to hand-arm vibration
- 2009
-
Ingår i: The Annals of Occupational Hygiene. - : Oxford University Press (OUP). - 1475-3162 .- 0003-4878. ; 53:5, s. 539-47
-
Tidskriftsartikel (refereegranskat)abstract
- This study clarifies whether the established frequency weighting procedure for evaluating exposure to hand-transmitted vibration can effectively evaluate the temporary changes in vibrotactile perception thresholds due to pre-exposure to vibration. In addition, this study investigates the relationship between changes of the vibrotactile perception thresholds and the normalized energy-equivalent frequency-weighted acceleration. The fingers of 10 healthy subjects, five male and five female, were exposed to vibration under 16 conditions with a combination of different frequencies, intensities, and exposure times. The vibration frequencies were 31.5 and 125 Hz and exposure lasted between 2 and 16 min. According to International Organization for Standardization (ISO) 5349-1, the energy-equivalent frequency-weighted acceleration for the experimental time of 16 min is 2.5 or 5.0 m s(-2) root-mean-square, corresponding to a 8-h equivalent acceleration, A(8), of approximately 0.5 and 0.9 m s(-2), respectively. A measure of the vibrotactile perception thresholds was conducted before the different exposures to vibration. Immediately after the vibration exposure, the acute effect was measured continuously on the exposed index finger for the first 75 s, followed by 30 s of measures every minute for a maximum of 10 min. If the subject's thresholds had not recovered, the measures continued for a maximum of 30 min with measurements taken every 5 min. Pre-exposure to vibration significantly influenced vibrotactile thresholds. This study concludes that the influence on the thresholds depends on the frequency of the vibration stimuli. Increased equivalent frequency-weighted acceleration resulted in a significant change in threshold, but the thresholds were unaffected when changes in the vibration magnitude were expressed as the frequency-weighted acceleration or the unweighted acceleration. Moreover, the frequency of the pre-vibration exposure significantly influenced (up to 25 min after exposure) recovery time of the vibrotactile thresholds. This study shows that the frequency weighting procedure in ISO 5349-1 is unable to predict the produced acute changes in the vibrotactile perception. Moreover, the results imply that the calculation of the 'energy-equivalent' frequency-weighted acceleration does not reflect the acute changes of the vibration perception thresholds due to pre-exposure to vibration. Furthermore, when testing for the vibrotactile thresholds, exposure to vibration on the day of a test might influence the results. Until further knowledge is obtained, the previous practice of 3 h avoidance of vibration exposure before assessment is recommended.
|
|
| 2. |
- Dahlman-Höglund, Anna, 1964, et al.
(författare)
-
Endotoxin in Size-Separated Metal Working Fluid Aerosol Particles
- 2016
-
Ingår i: Annals of Occupational Hygiene. - : Oxford University Press (OUP). - 0003-4878 .- 1475-3162. ; 60:7, s. 836-844
-
Tidskriftsartikel (refereegranskat)abstract
- Patients with airway symptoms working in metal working industries are increasing, despite efforts to improve the environmental air surrounding the machines. Our aim was to analyse the amount of endotoxin in size-separated airborne particles of metal working fluid (MWF) aerosol, by using the personal sampler Sioutas cascade impactor, to compare filter types, and to compare the concentration of airborne endotoxin to that of the corresponding MWFs. In a pilot field study, aerosols were collected in two separate machine halls on totally 10 occasions, using glass fibre and polytetrafluoroethylene (PTFE) filters in parallel at each station. Airborne endotoxin was distributed over all size fractions. While a major part was found in the largest size fraction (72%, 2.5-10 μm), up to 8% of the airborne endotoxin was detected in the smallest size fraction (<0.25 μm). Comparing the efficiency of the filter types, a significantly higher median endotoxin level was found with glass fibres filters collecting the largest particle-size fraction (1.2-fold) and with PTFE filters collecting the smallest ones (5-fold). The levels of endotoxin in the size-separated airborne particle fractions correlated to those of the MWFs supporting the aerosol-generating machines. Our study indicates that a significant part of inhalable aerosols of MWFs consists of endotoxin-containing particles below the size of intact bacteria, and thus small enough to readily reach the deepest part of the lung. Combined with other chemical irritants of the MWF, exposure to MWF aerosols containing endotoxin pose a risk to respiratory health problems. © 2016 The Author 2016. Published by Oxford University Press on behalf of the British Occupational Hygiene Society.
|
|
| 3. |
- Lillienberg, Linnea, 1942, et al.
(författare)
-
A population-based study on welding exposures at work and respiratory symptoms.
- 2008
-
Ingår i: The Annals of occupational hygiene. - : Oxford University Press (OUP). - 0003-4878 .- 1475-3162. ; 52:2, s. 107-15
-
Tidskriftsartikel (refereegranskat)abstract
- In the first European Community Respiratory Health Survey (ECRHS I), an excess asthma risk was associated with high exposure to gases and fumes, mineral and biological dusts. In a 9-year follow-up study (ECRHS II), the aim was to study if welding at work increases the risk of asthma symptoms, wheeze and chronic bronchitis symptoms. The study also aimed to identify specific welding risk factors. In a random population sample of individuals from 22 European centres in 10 countries, 316 males reported welding at work during the follow-up period. These individuals responded to a supplemental questionnaire about frequency of welding, use of different methods and materials, welding environment and respiratory protection. Cumulative exposure to welding fumes for the follow-up period was estimated by using a database on welding fume exposures. Log-binomial regression models were used to estimate prevalence ratios (PR) with 95% confidence intervals (CIs) for prevalence of asthma symptoms or asthma medication, wheeze and chronic bronchitis symptoms in relation to welding methods and welded materials as well as estimated cumulative welding fume exposure compared to an external reference group. In the study population of 316 males, 62% performed welding <1 h day(-1), 23% 1-3 h day(-1) and 15% >4 h day(-1). Welding was a common task in many occupations and only 7% of the individuals actually called themselves welders and flame cutters, while the largest groups doing welding worked in construction or were motor, agricultural and industrial mechanics and fitters. Welding at work was not associated with an increased prevalence of asthma symptoms or wheeze but there was an association with chronic bronchitis symptoms (PR = 1.33, 1.00-1.76). Using assigned cumulative exposure in tertiles showed that the lowest exposed tertile had the highest PR of bronchitis symptoms. Chronic bronchitis symptoms was significantly higher in those frequently welding in galvanized steel or iron (PR = 2.14, 1.24-3.68) and in those frequently manual welding stainless steel (PR = 1.92, 1.00-3.66). There was also an increase in the prevalence of wheeze in individuals welding painted metal (PR = 1.66, 0.99-2.78; PR = 1.83, 0.90-3.71). Welding with manual metal arc technique <1 day week(-1) showed a prevalence risk of 1.69 for wheeze (CI = 1.16-2.46). In conclusion, the present study shows an association between welding in galvanized material and stainless steel and chronic bronchitis symptoms. There was also an increased prevalence of wheeze and welding in painted metal. The results support that welding in coated material is a respiratory hazard underscoring the importance of preventive actions.
|
|
| 4. |
- Lillienberg, Linnea, 1942, et al.
(författare)
-
Exposures and Asthma Outcomes Using Two Different Job Exposure Matrices in a General Population Study in Northern Europe
- 2014
-
Ingår i: Annals of Occupational Hygiene. - : Oxford University Press (OUP). - 0003-4878 .- 1475-3162. ; 58:4, s. 469-481
-
Tidskriftsartikel (refereegranskat)abstract
- We have recently published a study on new-onset asthma in a large population in northern Europe using a modified job exposure matrix (N-JEM) to better reflect exposure assignment in these countries. The aim of this paper was to investigate how the N-JEM differs in exposure assignment and asthma risks from an already established JEM. The study comprised 6253 men and 7031 women from northern Europe, born 19451973, who had answered both a screening (19891992) and a follow-up questionnaire (19992001). During the study period (19802000), there were 136 men and 293 women with new-onset asthma. Hazard ratios of new-onset asthma were calculated for both JEMs using Cox regression models. The analyses were made separately for men and women and were also stratified for atopy. Cohens kappa () was used to show agreements in exposure assignment (yes/no) between the JEMs. Population attributable risks (PARs) were calculated as well. The agreement in exposure assignment between the JEMs was substantial for the group any exposure to asthma agents ( 0.78). The agreement between comparable exposure groups in the JEMs varied from 1.00 (pharmaceutical product antigens, textile dust, cleaning agents) to 0.27 (low molecular weight agents). Significant increased asthma risks were seen for men exposed to isocyanates and accidental peak exposure with both JEMs. With the N-JEM, increased asthma risks were seen for men exposed to plant-associated antigens (all and non-atopic), epoxy compounds (all and non-atopic), and acrylates (non-atopic). With the other JEM, increased asthma risks were seen in men and women exposed to possible exposure to irritant gases or fumes (all and non-atopic), a group classified as having low asthma risk. Men and women exposed to cleaning agents also showed significant asthma risks with both JEMs. PAR with the N-JEM was 14.3% for men and 6.6% for women, compared with 12.9% and 8.3% with the other JEM. Acrylates, epoxy compounds, and isocyanates are three exposure groups in the modified asthma JEM that might better reflect exposure situations in northern Europe than the already established JEM. Exposure to possible exposure to irritant gases or fumes, a low asthma risk group in the established JEM, seems to be a group with high asthma risk in northern Europe. It is important to continuously update JEMs, which are based only on occupational titles, in order to find new risk groups and to better reflect changes in work exposures when old risks disappear and new emerge.
|
|
| 5. |
- Lillienberg, Linnea, 1942, et al.
(författare)
-
Occupational Exposure and New-onset Asthma in a Population-based Study in Northern Europe (RHINE)
- 2013
-
Ingår i: Annals of Occupational Hygiene. - Oxford : Oxford University Press (OUP). - 0003-4878 .- 1475-3162. ; 57:4, s. 482-492
-
Tidskriftsartikel (refereegranskat)abstract
- In a large population-based study among adults in northern Europe the relation between occupational exposure and new-onset asthma was studied. The study comprised 13 284 subjects born between 1945 and 1973, who answered a questionnaire 19891992 and again 19992001. Asthma was defined as Asthma diagnosed by a physician with reported year of diagnose. Hazard ratios (HR), for new-onset adult asthma during 19802000, were calculated using a modified job-exposure matrix as well as high-risk occupations in Cox regression models. The analyses were made separately for men and women and were also stratified for atopy. During the observation period there were 429 subjects with new-onset asthma with an asthma incidence of 1.3 cases per 1000 person-years for men and 2.4 for women. A significant increase in new-onset asthma was seen for men exposed to plant-associated antigens (HR 3.6; 95% CI [confidence interval] 1.49.0), epoxy (HR 2.4; 95% CI 1.34.5), diisocyanates (HR 2.1; 95% CI 1.23.7) and accidental peak exposures to irritants (HR 2.4; 95% CI 1.34.7). Both men and women exposed to cleaning agents had an increased asthma risk. When stratifying for atopy an increased asthma risk were seen in non-atopic men exposed to acrylates (HR 3.3; 95% CI 1.47.5), epoxy compounds (HR 3.6; 95% CI 1.67.9), diisocyanates and accidental peak exposures to irritants (HR 3.0; 95% CI 1.27.2). Population attributable risk for occupational asthma was 14% for men and 7% for women. This population-based study showed that men exposed to epoxy, diisocyanates and acrylates had an increased risk of new-onset asthma. Non-atopics seemed to be at higher risk than atopics, except for exposure to high molecular weight agents. Increased asthma risks among cleaners, spray painters, plumbers, and hairdressers were confirmed.
|
|
| 6. |
- Lillienberg, Linnea, 1942, et al.
(författare)
-
Respiratory Symptoms and Exposure-Response Relations in Workers exposed to Metalworking Fluid Aerosols
- 2010
-
Ingår i: Annals of Occupational Hygiene. - : Oxford University Press (OUP). - 0003-4878 .- 1475-3162. ; 54:4, s. 403-411
-
Tidskriftsartikel (refereegranskat)abstract
- The aim of the study was to identify specific health risks and exposure-response relationships associated with exposure to metalworking fluid (MWF) aerosols. In a cross-sectional study of machine workers exposed to MWF aerosols in five companies in Sweden, a self-administered questionnaire about health symptoms, work tasks, and exposure situations was sent out to 2294 employees, 1632 exposed and 662 referents. Referents were office workers and metal workers not working with MWFs. In four of the companies, there were recent measurements of personal exposure to MWF aerosols. Log-binomial regression models were used to estimate prevalence ratios with 95% confidence intervals for different health outcomes in relation to different variables of exposure. The response rate after two reminders was 67% resulting in 1048 (923 male, 125 female) workers exposed to MWF aerosols and 451 (374 male, 77 female) referents. The study indicates that metal workers in Sweden currently exposed to a mean value of MWF aerosols of 0.4 mg m(-3) have a significantly higher prevalence of wheeze, chronic bronchitis, chronic rhinitis, and eye irritation compared to the referents. At a mean exposure of 0.4 mg m(-3), a level below the Swedish 8-h exposure limit value of 1 mg m(-3), machine operators showed increased prevalence of symptoms in eyes and airways. Thus, the current exposure limit value does not seem to protect the workers from such symptoms.
|
|
| 7. |
- Neitzel, R. L., et al.
(författare)
-
Comparison of Multiple Measures of Noise Exposure in Paper Mills
- 2016
-
Ingår i: Annals of Occupational Hygiene. - : Oxford University Press (OUP). - 0003-4878 .- 1475-3162. ; 60:5, s. 581-596
-
Tidskriftsartikel (refereegranskat)abstract
- Noise exposures are associated with a host of adverse health effects, yet these exposures remain inadequately characterized in many industrial operations, including paper mills. We assessed noise at four paper mills using three measures: (i) personal noise dosimetry, (ii) area noise measurements, and (iii) questionnaire items addressing several different aspects of perceived noise exposure. We assessed exposures to noise characterized using the three measures and compared the relationships between them. We also estimated the validity of each of the three measures using a novel application of the Method of Triads, which does not appear to have been used previously in the occupational health literature. We collected 209 valid dosimetry measurements and collected perceived noise exposure survey items from 170 workers, along with 100 area measurements. We identified exposures in excess of 85 dBA at all mills. The dosimetry and area noise measurements assigned to individual subjects generally showed good agreement, but for some operations within mill, large differences between the two measures were observed, and a substantial fraction of paired measures differed by > 5 dB. Perceived noise exposures varied greatly between the mills, particularly for an item related to difficulty speaking in noise. One perceived noise exposure item related to difficulty hearing due to noise showed strong and significant correlations with both dosimetry and area measurements. The Method of Triads analysis showed that dosimetry measures had the highest estimated validity coefficient (0.70), and that the best performing perceived exposure measure had validity that exceeded that of area measurements (0.48 versus 0.40, respectively). Workers in Swedish pulp mills have the potential for exposures to high levels of noise. Our results suggest that, while dosimetry remains the preferred approach to exposure assessment, perceived noise exposures can be used to evaluate potential exposures to noise in epidemiological studies.
|
|
| 8. |
- Nygren, Olle, et al.
(författare)
-
A test method for assessment of spill and leakage from drug preparation systems
- 2005
-
Ingår i: Ann Occup Hyg. - : Oxford University Press. - 0003-4878 .- 1475-3162. ; 49:8, s. 711-8
-
Tidskriftsartikel (refereegranskat)abstract
- Anti-cancer drugs are reactive compounds with known adverse health effects. To prevent occupational exposure to these drugs, there are, in most countries, regulations for handling anti-cancer drugs. Many preparation systems are available, e.g. isolators, biological safety cabinets (BSCs), filter spikes (venting spikes with micro-pore filter) and closed systems (e.g. PhaSeal). Although these systems are used, there are reports of exposure. This causes concern over how efficient these systems are to prevent spill and leakage that may cause undesired exposure when handling cytotoxic drugs. Today, this knowledge is lacking. This paper presents a method (Tc-method) for testing drug preparation systems for spill and leakage. The Tc-method is based on 99Tc(m) as a tracer, with which drug vials used for test preparations are spiked. Wipe samples are then collected around the working area to measure spill and leakage. The Tc-method has been validated using an independent method, showing good agreement between the methods. Spills down to 1 nl cm(-2) can be determined. In an appendix, the Tc-method is described in a detailed step-by-step procedure.
|
|
| 9. |
- Taube, Fabian, 1967
(författare)
-
Manganese in Occupational Arc Welding Fumes—Aspects on Physiochemical Properties, with Focus on Solubility
- 2013
-
Ingår i: The Annals of occupational hygiene. - : Oxford University Press (OUP). - 0003-4878 .- 1475-3162. ; 57:1-2, s. 6-25
-
Tidskriftsartikel (refereegranskat)abstract
- Physicochemical properties, such as particle sizes, composition, and solubility of welding fumes are decisive for the bioaccessibility of manganese and thereby for the manganese cytotoxic and neurotoxic effects arising from various welding fumes. Because of the diverse results within the research on welding fume solubility, this article aims to review and discuss recent literature on physicochemical properties of gas metal arc welding, shielded metal arc welding, and flux-cored arc welding fumes, with focus on solubility properties. This article also presents a short introduction to the literature on arc welding techniques, health effects from manganese, and occupational exposure to manganese among welders.
|
|
