| 1. |
- Adeel, Muhammad, et al.
(författare)
-
2D metal azolate framework as nanozyme for amperometric detection of glucose at physiological pH and alkaline medium
- 2021
-
Ingår i: Microchimica Acta. - : Springer. - 0026-3672 .- 1436-5073. ; 188:3
-
Tidskriftsartikel (refereegranskat)abstract
- The synthesis of Co-based two-dimensional (2D) metal azolate framework nanosheets (MAF-5-CoII NS) is described using a simple hydrothermal method. The product was isostructural to MAF-5 (Zn). The as-prepared MAF-5-CoII NS exhibited high surface area (1155 m2/g), purity, and crystallinity. The MAF-5-CoII NS–modified screen-printed electrode (MAF-5-CoII NS/SPE) was used for nonenzymatic detection of glucose in diluted human blood plasma (BP) samples with phosphate buffer saline (PBS, pH 7.4) and NaOH (0.1 M, pH 13.0) solutions. The MAF-5-CoII NS nanozyme displayed good redox activity in both neutral and alkaline media with the formation of CoII/CoIII redox pair, which induced the catalytic oxidation of glucose. Under the optimized detection potential, the sensor presented a chronoamperometric current response for the oxidation of glucose with two wide concentration ranges in PBS-diluted (62.80 to 180 μM and 305 to 8055 μM) and NaOH-diluted (58.90 to 117.6 μM and 180 to 10,055 μM) BP samples, which were within the limit of blood glucose levels of diabetic patients before (4.4–7.2 mM) and after (10 mM) meals (recommended by the American Diabetes Association). The sensor has a limit of detection of ca. 0.25 and 0.05 μM, respectively, and maximum sensitivity of ca. 36.55 and 1361.65 mA/cm2/mM, respectively, in PBS- and NaOH-diluted BP samples. The sensor also displayed excellent stability in the neutral and alkaline media due to the existence of hydrophobic linkers (2-ethyl imidazole) in the MAF-5-CoII NS, good repeatability and reproducibility, and interference-free signals. Thus, MAF-5-CoII NS is a promising nanozyme for the development of the disposable type of sensor for glucose detection in human body fluids.
|
|
| 2. |
- Afanasiev, Sergey V., et al.
(författare)
-
Experimental apparatus to study crystal channeling in an external SPS beamline
- 2007
-
Ingår i: Proceedings of SPIE, the International Society for Optical Engineering. - : SPIE. - 0277-786X .- 1996-756X. ; 6634
-
Tidskriftsartikel (refereegranskat)abstract
- For the new generation of high intensity hadronic machines as, for instance, LHC, halo collimation is a necessary issue for the accelerator to operate at the highest possible luminosity and to prevent the damage of superconductor magnets.1 We propose an experiment aimed to systematic study of the channeling phenomenology and of the newly observed "volume reflection" effect. This experiment will be performed for an external SPS beamline and will make use of a primary proton beam with 400 GeV/c momentum and very small (∼ 3 μrad) divergence. The advantage of a proposed experiment is precise tracking of particles that interacted with a crystal, so that to determine the single-pass efficiency for all the processes involved. For this purpose, a telescope equipped with high-resolution silicon microstrip detectors will be used. New generation silicon crystals and an extra-precise goniometer are mandatory issues. Main goal of the experiment is to get the precise information on channeling of relativistic particles and, ultimately, on the feasibility of such technique for halo collimation at LHC. In this contribution we review the status of the setting-up of experimental apparatus and its future development in sight of the planned run in September 2006.
|
|
| 3. |
- Aftab, Umair, et al.
(författare)
-
Two step synthesis of TiO2–Co3O4 composite for efficient oxygen evolution reaction
- 2021
-
Ingår i: International journal of hydrogen energy. - : Elsevier. - 0360-3199 .- 1879-3487. ; 46:13, s. 9110-9122
-
Tidskriftsartikel (refereegranskat)abstract
- For an active hydrogen gas generation through water dissociation, the sluggish oxygen evolution reaction (OER) kinetics due to large overpotential is a main hindrance. Herein, a simple approach is used to produce composite material based on TiO2/Co3O4 for efficient OER and overpotential is linearly reduced with increasing amount of TiO2. The scanning electron microscopy (SEM) and high resolution transmission electron microscopy (HRTEM) investigations reveal the wire like morphology of composite materials, formed by the self-assembly of nanoparticles. The titania nanoparticles were homogenously distributed on the larger Co3O4 nanoparticles. The powder x-ray diffraction revealed a tetragonal phase of TiO2 and the cubic phase of Co3O4 in the composite materials. Composite samples with increasing TiO2 content were obtained (18%, 33%, 41% and 65% wt.). Among the composites, cobalt oxide-titanium oxide with the highest TiO2 content (CT-20) possesses the lowest overpotential for OER with a Tafel slope of 60 mV dec−1 and an exchange current density of 2.98 × 10−3A/cm2. The CT-20 is highly durable for 45 h at different current densities of 10, 20 and 30 mA/cm2. Electrochemical impedance spectroscopy (EIS) confirmed the fast charge transport for the CT-20 sample, which potentially accelerated the OER kinetics. These results based on a two-step methodology for the synthesis of TiO2/Co3O4 material can be useful and interesting for various energy storage and energy conversion systems.
|
|
| 4. |
- Ahdikari, Rajesh, et al.
(författare)
-
High Efficiency, Pt-free Photoelectrochemical Cells for Solar Hydrogen Generation based on “Giant” Quantum Dots
- 2016
-
Ingår i: Nano Energy. - : Elsevier BV. - 2211-2855. ; 27, s. 265-274
-
Tidskriftsartikel (refereegranskat)abstract
- Quantum dot (QD) sensitized TiO2 is considered as a highly promising photoanode material for photoelectrochemical (PEC) solar hydrogen production. However, due to its limited stability, the photoanode suffers from degradation of its long-term PEC performance. Here, we report the design and characterization of a high-efficiency and long-term stable Pt-free PEC cell. The photoanode is composed of a mesoporous TiO2 nanoparticle film sensitized with “giant” core@shell QDs for PEC solar hydrogen generation. The thick shell enhances light absorption in the visible range, increases the stability of the QDs and does not inhibit charge separation, injection and transport, needed for proper operation of the device. We prepared thin films of Cu2S nanoflakes through a simple and reproducible procedure, and used them as counter-electrodes replacing the standard Pt film, resulting in equivalent performances of the PEC cell. We obtained an unprecedented photocurrent density (~10 mA/cm2) for “giant” QDs based PEC devices (and corresponding H2 generation) and a very promising stability, indicating that the proposed cell architecture is a good candidate for long-term stable QD-based PEC solar hydrogen generation.
|
|
| 5. |
- Akbar, Kamran, et al.
(författare)
-
Carbon Dots for Photocatalytic Degradation of Aqueous Pollutants : Recent Advancements
- 2021
-
Ingår i: Advanced Optical Materials. - : John Wiley & Sons. - 2162-7568 .- 2195-1071. ; 9:17
-
Forskningsöversikt (refereegranskat)abstract
- The immense progress of humanity on the technological, domestic, and industrial fronts comes at the cost of polluting the planet. Aquatic pollution is particularly dangerous since all life forms are directly linked to it. Each year tons of industrial and domestic pollutants make their way into aqueous systems. Efficient removal/degradation of these pollutants is of prime importance for the sustainable future. Among many technologies, photodegradation is an emerging and promising method for the successful removal of aqueous pollutants since it is powered by abundant solar light. The last decade had shown that carbon dots are among the most promising materials that can be utilized as an efficient tool to derive various solar-driven chemical reactions. Carbon dots possess unique photophysical and chemical properties such as light-harvesting over a broad-spectrum region, upconversion photoluminescence, photosensitizers, chemical inertness, and bivalent redox character, etc. The ease of synthesis of carbon dots at low cost also contributes hugely to their utilizations as an efficient photocatalyst for the degradation of aqueous pollutants. This review summarizes the recent progress made in the field of photodegradation of aqueous pollutants with the aid of carbon dots and their hybrids, highlighting the critical role carbon dots can play in the field.
|
|
| 6. |
- Alberoni, Chiara, et al.
(författare)
-
Ceria doping boosts methylene blue photodegradation in titania nanostructures
- 2021
-
Ingår i: Materials Chemistry Frontiers. - : Royal Society of Chemistry. - 2052-1537. ; 5:11, s. 4138-4152
-
Tidskriftsartikel (refereegranskat)abstract
- Ceria-doped titania photocatalysts (ceria loading 0.25–5.0 wt%) were synthesized by hydrothermal methods for water remediation. Nanotubes (CeTNTx) and nanoparticles (CeTNPx) were obtained. Ceria doping was applied to tune the electronic properties of nanostructured titania, boosting its photocatalytic activity. CeTNT nanostructures contained anatase as the only titania phase, whereas the CeTNP series consisted of both anatase and rutile polymorphs. The Ce addition induced a decrease in the energy gap, allowing enhancement of visible light harvesting. The photodegradation of methylene blue, MB, in aqueous solution was chosen to study the influence of the morphology and the ceria loading on the photocatalytic response, under UV and solar light. Both CeO2–TiO2 nanoparticles and nanotubes were found to be very active under UV light. The highest MB degradation rates were obtained for the 0.25 wt% CeO2 doping, for both nanotubes and nanoparticles (0.123 and 0.146 min−1, respectively), able to photodegrade completely the dye after 120 min. The two samples are stable after a 3-cycle reusability test. The photo-response under simulated solar light confirmed that doping titania with ceria allows harvesting visible light absorption, enhancing its photoactivity. A maximum efficiency of 85% under simulated sunlight at a degradation rate of 0.054 min−1 was obtained. Transient photoluminescence confirmed that MB acts as a charge scavenger for the composite system. These results pointed out ceria-doped titania nanostructures as a promising class of photocatalysts for the degradation of dyes and other hazardous organic compounds in wastewater.
|
|
| 7. |
- Alvi, Sajid Ali, et al.
(författare)
-
Adaptive nanolaminate coating by atomic layer deposition
- 2019
-
Ingår i: Thin Solid Films. - : Elsevier. - 0040-6090 .- 1879-2731. ; 692
-
Tidskriftsartikel (refereegranskat)abstract
- Atomic layer deposition (ALD) was used to deposit ZnO/Al2O3/V2O5 nanolaminate coatings to demonstrate a coating system with temperature adaptive frictional behaviour. The nanolaminate coating exhibited excellent conformity and crack-free coating of thickness 110 nm over Inconel 718 substrate. The ALD trilayer coating showed a hardness and elastic modulus of 12 GPa and 193 GPa, respectively. High-temperature tribology of the nanolaminate trilayer was tested against steel ball in dry sliding condition at 25 °C (room temperature, RT), 200 °C, 300 °C, and 400 °C. It was found that the nanolaminate coating showed a low coefficient of friction (COF) and wear rate at RT and 300 °C. The trilayer coating was found intact and stable at all temperatures during the friction tests. The adaptability of nanolaminate coating with the temperature was verified by performing the cyclic friction test at 300 °C and RT. The low COF and wear rate had been attributed to the (100) and (002) basal plane sliding of ZnO top layer, and the interlayer sliding of weakly bonded planes parallel to (001) plane in V2O5 bottom layer. Furthermore, even after the removal of ZnO coating during the tribotest, the bottom V2O5 layer coating stabilized the COF and wear rate at RT and 300 °C.
|
|
| 8. |
- Alvi, Sajid, et al.
(författare)
-
Enhanced mechanical, thermal and electrical properties of high‐entropy HfMoNbTaTiVWZr thin film metallic glass and its nitrides
- 2022
-
Ingår i: Advanced Engineering Materials. - : John Wiley & Sons. - 1438-1656 .- 1527-2648. ; 24:9
-
Tidskriftsartikel (refereegranskat)abstract
- The inception of high-entropy alloy promises to push the boundaries for new alloy design with unprecedented properties. This work reports entropy stabilisation of an octonary refractory, HfMoNbTaTiVWZr, high-entropy thin film metallic glass, and derived nitride films. The thin film metallic glass exhibited exceptional ductility of ≈60% strain without fracture and compression strength of 3 GPa in micro-compression, due to the presence of high density and strength of bonds. The thin film metallic glass shows thermal stability up to 750 °C and resistance to Ar-ion irradiation. Nitriding during film deposition of HfMoNbTaTiVWZr thin film of strong nitride forming refractory elements results in deposition of nanocrystalline nitride films with compressive strength, hardness, and thermal stability of up to 10 GPa, 18.7 GPa, and 950 °C, respectively. The high amount of lattice distortion in the nitride films leads to its insulating behaviour with electrical conductivity as low as 200 S cm−1 in the as-deposited film. The design and exceptional properties of the thin film metallic glass and derived nitride films may open up new avenues of development of bulk metallic glasses and the application of refractory-based high entropy thin films in structural and functional applications.
|
|
| 9. |
- Alvi, Sajid, et al.
(författare)
-
Synthesis and Mechanical Characterization of a CuMoTaWV High-Entropy Film by Magnetron Sputtering
- 2020
-
Ingår i: ACS Applied Materials and Interfaces. - : American Chemical Society (ACS). - 1944-8244 .- 1944-8252. ; 12:18, s. 21070-21079
-
Tidskriftsartikel (refereegranskat)abstract
- Development of high-entropy alloy (HEA) films is a promising and cost-effective way to incorporate these materials of superior properties in harsh environments. In this work, a refractory high-entropy alloy (RHEA) film of equimolar CuMoTaWV was deposited on silicon and 304 stainless-steel substrates using DC-magnetron sputtering. A sputtering target was developed by partial sintering of an equimolar powder mixture of Cu, Mo, Ta, W, and V using spark plasma sintering. The target was used to sputter a nanocrystalline RHEA film with a thickness of ∼900 nm and an average grain size of 18 nm. X-ray diffraction of the film revealed a body-centered cubic solid solution with preferred orientation in the (110) directional plane. The nanocrystalline nature of the RHEA film resulted in a hardness of 19 ± 2.3 GPa and an elastic modulus of 259 ± 19.2 GPa. A high compressive strength of 10 ± 0.8 GPa was obtained in nanopillar compression due to solid solution hardening and grain boundary strengthening. The adhesion between the RHEA film and 304 stainless-steel substrates was increased on annealing. For the wear test against the E52100 alloy steel (Grade 25, 700–880 HV) at 1 N load, the RHEA film showed an average coefficient of friction (COF) and wear rate of 0.25 (RT) and 1.5 (300 °C), and 6.4 × 10–6 mm3/N m (RT) and 2.5 × 10–5 mm3/N m (300 °C), respectively. The COF was found to be 2 times lower at RT and wear rate 102 times lower at RT and 300 °C than those of 304 stainless steel. This study may lead to the processing of high-entropy alloy films for large-scale industrial applications.
|
|
| 10. |
- Amin, Sidra, et al.
(författare)
-
A practical non-enzymatic urea sensor based on NiCo2O4 nanoneedles
- 2019
-
Ingår i: RSC Advances. - : Royal Society of Chemistry. - 2046-2069. ; 9:25, s. 14443-14451
-
Tidskriftsartikel (refereegranskat)abstract
- We propose a new facile electrochemical sensing platform for determination of urea, based on a glassy carbon electrode (GCE) modified with nickel cobalt oxide (NiCo2O4) nanoneedles. These nanoneedles are used for the first time for highly sensitive determination of urea with the lowest detection limit (1 μM) ever reported for the non-enzymatic approach. The nanoneedles were grown through a simple and low-temperature aqueous chemical method. We characterized the structural and morphological properties of the NiCo2O4 nanoneedles by TEM, SEM, XPS and XRD. The bimetallic nickel cobalt oxide exhibits nanoneedle morphology, which results from the self-assembly of nanoparticles. The NiCo2O4 nanoneedles are exclusively composed of Ni, Co, and O and exhibit a cubic crystalline phase. Cyclic voltammetry was used to study the enhanced electrochemical properties of a NiCo2O4 nanoneedle-modified GCE by overcoming the typical poor conductivity of bare NiO and Co3O4. The GCE-modified electrode is highly sensitive towards urea, with a linear response (R2 = 0.99) over the concentration range 0.01–5 mM and with a detection limit of 1.0 μM. The proposed non-enzymatic urea sensor is highly selective even in the presence of common interferents such as glucose, uric acid, and ascorbic acid. This new urea sensor has good viability for urea analysis in urine samples and can represent a significant advancement in the field, owing to the simple and cost-effective fabrication of electrodes, which can be used as a promising analytical tool for urea estimation.
|
|
