| 1. |
- Aho-Mantila, L., et al.
(författare)
-
Assessment of SOLPS5.0 divertor solutions with drifts and currents against L-mode experiments in ASDEX Upgrade and JET
- 2017
-
Ingår i: Plasma Physics and Controlled Fusion. - : IOP PUBLISHING LTD. - 0741-3335 .- 1361-6587. ; 59:3
-
Tidskriftsartikel (refereegranskat)abstract
- The divertor solutions obtained with the plasma edge modelling tool SOLPS5.0 are discussed. The code results are benchmarked against carefully analysed L-mode discharges at various density levels with and without impurity seeding in the full-metal tokamaks ASDEX Upgrade and JET. The role of the cross-field drifts and currents in the solutions is analysed in detail, and the improvements achieved by fully activating the drift and current terms in view of matching the experimental signals are addressed. The persisting discrepancies are also discussed.
|
|
| 2. |
- Aiba, N., et al.
(författare)
-
Analysis of ELM stability with extended MHD models in JET, JT-60U and future JT-60SA tokamak plasmas
- 2018
-
Ingår i: Plasma Physics and Controlled Fusion. - : IOP Publishing. - 0741-3335 .- 1361-6587. ; 60:1
-
Tidskriftsartikel (refereegranskat)abstract
- The stability with respect to a peeling-ballooning mode (PBM) was investigated numerically with extended MHD simulation codes in JET, JT-60U and future JT-60SA plasmas. The MINERVA-DI code was used to analyze the linear stability, including the effects of rotation and ion diamagnetic drift (omega(*i)), in JET-ILW and JT-60SA plasmas, and the JOREK code was used to simulate nonlinear dynamics with rotation, viscosity and resistivity in JT-60U plasmas. It was validated quantitatively that the ELM trigger condition in JET-ILW plasmas can be reasonably explained by taking into account both the rotation and omega(*i) effects in the numerical analysis. When deuterium poloidal rotation is evaluated based on neoclassical theory, an increase in the effective charge of plasma destabilizes the PBM because of an acceleration of rotation and a decrease in omega(*i). The difference in the amount of ELM energy loss in JT-60U plasmas rotating in opposite directions was reproduced qualitatively with JOREK. By comparing the ELM affected areas with linear eigenfunctions, it was confirmed that the difference in the linear stability property, due not to the rotation direction but to the plasma density profile, is thought to be responsible for changing the ELM energy loss just after the ELM crash. A predictive study to determine the pedestal profiles in JT-60SA was performed by updating the EPED1 model to include the rotation and w*i effects in the PBM stability analysis. It was shown that the plasma rotation predicted with the neoclassical toroidal viscosity degrades the pedestal performance by about 10% by destabilizing the PBM, but the pressure pedestal height will be high enough to achieve the target parameters required for the ITER-like shape inductive scenario in JT-60SA.
|
|
| 3. |
- Aiba, N., et al.
(författare)
-
Numerical analysis of ELM stability with rotation and ion diamagnetic drift effects in JET
- 2017
-
Ingår i: Nuclear Fusion. - : IOP PUBLISHING LTD. - 0029-5515 .- 1741-4326. ; 57:12
-
Tidskriftsartikel (refereegranskat)abstract
- Stability to the type-I edge localized mode (ELM) in JET plasmas was investigated numerically by analyzing the stability to a peeling-ballooning mode with the effects of plasma rotation and ion diamagnetic drift. The numerical analysis was performed by solving the extended Frieman-Rotenberg equation with the MINERVA-DI code. To take into account these effects in the stability analysis self-consistently, the procedure of JET equilibrium reconstruction was updated to include the profiles of ion temperature and toroidal rotation, which are determined based on the measurement data in experiments. With the new procedure and MINERVA-DI, it was identified that the stability analysis including the rotation effect can explain the ELM trigger condition in JET with ITER like wall (JET-ILW), though the stability in JET with carbon wall (JET-C) is hardly affected by rotation. The key difference is that the rotation shear in JET-ILW plasmas analyzed in this study is larger than that in JET-C ones, the shear which enhances the dynamic pressure destabilizing a peeling-ballooning mode. In addition, the increase of the toroidal mode number of the unstable MHD mode determining the ELM trigger condition is also important when the plasma density is high in JET-ILW. Though such modes with high toroidal mode number are strongly stabilized by the ion diamagnetic drift effect, it was found that plasma rotation can sometimes overcome this stabilizing effect and destabilizes the peeling-ballooning modes in JET-ILW.
|
|
| 4. |
|
|
| 5. |
- Andersson, Peter, 1981-, et al.
(författare)
-
Coincidence spectroscopy for increased sensitivity in radionuclide monitoring
- 2022
-
Konferensbidrag (övrigt vetenskapligt/konstnärligt)abstract
- The majority of the energy in a nuclear explosion is released in the immediate blast and the initial radiation accounts. The remaining fraction is released through radioactive decay of the explosion's fission products and neutron activation products over a longer time span. This allows for the detection of a nuclear explosion by detecting the presence of residual decay. Radionuclide monitoring stations for detection of radioactive emissions to the atmosphere is thereby an important tool in the verification of compliance with nuclear disarmament treaties. In particular, the globally spanning radionuclide station network of the International Monitoring System (IMS) has been implemented for verification of the Comprehensive Nuclear-Test-Ban Treaty.High Purity Germanium (HPGe) detectors are workhorses in radionuclide monitoring. The detection of characteristic gamma rays can be used to disclose the presence of signature nuclides produced innuclear weapon tests. A particular development that has potential to improve the sensitivity of radionuclide monitoring is the coincidence technique where decaying nuclides that emit several coincident gamma rays can be detected at much smaller activity concentrations than with conventional gamma spectroscopy.In this project, dedicated gamma-gamma coincidence detectors are being developed, utilizing electronically segmented HPGe detectors. These detectors are expected to be highly sensitive to low-activity samples of nuclides that present coincident emissions of gamma rays. In this paper we present the concept, define performance parameters, and explore the performance of such detectors to a subset of radionuclides of particular CTBT relevance. In addition, we discuss the path forward in developing a next generation gamma-gamma coincidence spectroscopy system of segmented HPGe.
|
|
| 6. |
- Andersson, Peter, 1981-, et al.
(författare)
-
Design and initial 1D radiography tests of the FANTOM mobile fast-neutron radiography and tomography system
- 2014
-
Ingår i: Nuclear Instruments and Methods in Physics Research Section A. - : Elsevier BV. - 0168-9002 .- 1872-9576. ; 756, s. 82-93
-
Tidskriftsartikel (refereegranskat)abstract
- The FANTOM system is a tabletop sized fast-neutron radiography and tomography system newly developed at the Applied Nuclear Physics Division of Uppsala University. The main purpose of the system is to provide time-averaged steam-and-water distribution measurement capability inside the metallic structures of two-phase test loops for Light Water Reactor thermal-hydraulic studies using a portable fusion neutron generator. The FANTOM system provides a set of 1D neutron transmission data, which may be inserted into tomographic reconstruction algorithms to achieve a 2D mapping of the steam-and-water distribution. In this paper, the selected design of FANTOM is described and motivated. The detector concept is based on plastic scintillator elements, separated for spatial resolution. Analysis of pulse heights on an event-to-event basis is used for energy discrimination. Although the concept allows for close stacking of a large number of detector elements, this demonstrator is equipped with only three elements in the detector and one additional element for monitoring the yield from the neutron generator. The first measured projections on test objects of known configurations are presented. These were collected using a Sodern Genie 16 neutron generator with an isotropic yield of about 1E8 neutrons per second, and allowed for characterization of the instrument’s capabilities. At an energy threshold of 10 MeV, the detector offered a count rate of about 500 cps per detector element. The performance in terms of spatial resolution was validated by fitting a Gaussian Line Spread Function to the experimental data, a procedure that revealed a spatial unsharpness in good agreement with the predicted FWHM of 0.5 mm.
|
|
| 7. |
- Andersson, Peter, 1981-, et al.
(författare)
-
Neutron tomography of axially symmetric objects using 14 MeV neutrons from a portable neutron generator
- 2014
-
Ingår i: Review of Scientific Instruments. - : AIP Publishing. - 0034-6748 .- 1089-7623. ; 85:8, s. 085109-
-
Tidskriftsartikel (refereegranskat)abstract
- In nuclear boiling water reactor cores, the distribution of water and steam (void) is essential for both safety and efficiency reasons. In order to enhance predictive capabilities, void distribution assessment is performed in two-phase test-loops under reactor-relevant conditions. This article proposes the novel technique of fast-neutron tomography using a portable deuterium-tritium neutron generator to determine the void distribution in these loops.Fast neutrons have the advantage of high transmission through the metallic structures and pipes typically concealing a thermal-hydraulic test loop, while still being fairly sensitive to the water/void content. However, commercially available fast-neutron generators also have the disadvantage of a relatively low yield and fast-neutron detection also suffers from relatively low detection efficiency. Fortunately, some loops are axially symmetric, a property which can be exploited to reduce the amount of data needed for tomographic measurement, thus limiting the interrogation time needed.In this article, three axially-symmetric test objects depicting a thermal-hydraulic test loop have been examined; steel pipes with outer diameter 24 mm, thickness 1.5 mm and with three different distributions of the plastic material POM inside the pipes. Data recorded with the FANTOM fast-neutron tomography instrument have been used to perform tomographic reconstructions to assess their radial material distribution. Here, a dedicated tomographic algorithm that exploits the symmetry of these objects has been applied, which is described in the paper.Results are demonstrated in 20 rixel (radial pixel) reconstructions of the interior constitution and 2D visualization of the pipe interior is demonstrated. The local POM attenuation coefficients in the rixels were measured with errors (RMS) of 0.025, 0.020 and 0.022 cm-1, solid POM attenuation coefficient. The accuracy and precision is high enough to provide a useful indication on the flow mode, and a visualization of the radial material distribution can be obtained. A benefit of this system is its potential to be mounted at any axial height of a two-phase test section without requirements for pre-fabricated entrances or windows. This could mean a significant increase in flexibility of the void distribution assessment capability at many existing two-phase test loops.
|
|
| 8. |
- Andersson, Peter, 1981-, et al.
(författare)
-
Neutron Tomography Using Mobile Neutron Generators for Assessment of Void Distributions in Thermal Hydraulic Test Loops
- 2015
-
Konferensbidrag (refereegranskat)abstract
- Detailed knowledge of the lateral distribution of steam (void) and water in a nuclear fuel assembly is of great value for nuclear reactor operators and fuel manufacturers, with consequences for both reactor safety and economy of operation. Therefore, nuclear relevant two-phase flows are being studied at dedicated thermal-hydraulic test loop, using twophase flow systems ranging from simplified geometries such as heated circular pipes to full scale mock-ups of nuclear fuel assemblies. Neutron tomography (NT) has been suggested for assessment of the lateral distribution of steam and water in such test loops, motivated by a good ability of neutrons to penetrate the metallic structures of metal pipes and nuclear fuel rod mock-ups, as compared to e. g. conventional X-rays, while the liquid water simultaneously gives comparatively good contrast. However, these stationary test loops require the measurement setup to be mobile, which is often not the case for NT setups. Here, it is acknowledged that fast neutrons of 14 MeV from mobile neutron generators constitute a viable option for a mobile NT system. We present details of the development of neutron tomography for this purpose at the division of Applied Nuclear Physics at Uppsala University. Our concept contains a portable neutron generator, exploiting the fusion reaction of deuterium and tritium, and a detector with plastic scintillator elements designed to achieve adequate spatial and energy resolution, all mounted in a light-weight frame without collimators or bulky moderation to allow for a mobile instrument that can be moved about the stationary thermal hydraulic test sections. The detector system stores event-to-event pulse-height information to allow for discrimination based on the energy deposition in the scintillator elements. Experimental results from the tomographic assessment of axially symmetric test objects are shown, as well as simulation results from a scaled up version of the instrument for nonsymmetrical objects in quarter fuel-bundle size objects. In conclusion, the application of tomography on inch-wide vertical pipes has been experimentally demonstrated and simulation results indicate that tomography of the void distribution in nonsymmetrical vertical flows in quarter BWR fuel bundles is also feasible.
|
|
| 9. |
|
|
| 10. |
- Andersson, Peter, 1981-, et al.
(författare)
-
Simulation of the response of a segmented High-Purity Germanium detector for gamma emission tomography of nuclear fuel
- 2020
-
Ingår i: SN Applied Sciences. - : Springer. - 2523-3963 .- 2523-3971. ; 2
-
Tidskriftsartikel (refereegranskat)abstract
- Irradiation testing of nuclear fuel is routinely performed in nuclear test reactors. For qualification and licensing of Accident Tolerant Fuels or Generation IV reactor fuels, an extensive increase in irradiation testing is foreseen in order to fill the gaps of existing validation data, both in normal operational conditions and in order to identify operational limits.Gamma Emission Tomography (GET) has been demonstrated as a viable technique for studies of the behavior of irradiated nuclear fuel, e.g. measurement of fission gas release and inspection of fuel behavior under Loss-Of-Coolant Accident conditions. In this work, the aim is to improve the technique of GET for irradiated nuclear fuel by developing a detector concept for an improved tomography system that allows for a higher spatial resolution and/or faster interrogation.We present the working principles of a novel concept for gamma emission tomography using a segmented High Purity Germanium (HPGe) detector. The performance of this concept was investigated using the Monte Carlo particle transport code MCNP. In particular, the data analysis of the proposed detector was evaluated, and the performance, in terms of full energy efficiency and localization failure rate, has been evaluated.We concluded that the segmented HPGe detector has an advantageous performance as compared to the traditional single-channel detector systems. Due to the scattering nature of gamma rays, a trade-off is presented between efficiency and cross-talk; however, the performance is nevertheless a substantial improvement over the currently used single-channel HPGe detector systems.
|
|
