| 1. |
- Aho-Mantila, L., et al.
(författare)
-
Assessment of SOLPS5.0 divertor solutions with drifts and currents against L-mode experiments in ASDEX Upgrade and JET
- 2017
-
Ingår i: Plasma Physics and Controlled Fusion. - : IOP PUBLISHING LTD. - 0741-3335 .- 1361-6587. ; 59:3
-
Tidskriftsartikel (refereegranskat)abstract
- The divertor solutions obtained with the plasma edge modelling tool SOLPS5.0 are discussed. The code results are benchmarked against carefully analysed L-mode discharges at various density levels with and without impurity seeding in the full-metal tokamaks ASDEX Upgrade and JET. The role of the cross-field drifts and currents in the solutions is analysed in detail, and the improvements achieved by fully activating the drift and current terms in view of matching the experimental signals are addressed. The persisting discrepancies are also discussed.
|
|
| 2. |
- Aiba, N., et al.
(författare)
-
Numerical analysis of ELM stability with rotation and ion diamagnetic drift effects in JET
- 2017
-
Ingår i: Nuclear Fusion. - : IOP PUBLISHING LTD. - 0029-5515 .- 1741-4326. ; 57:12
-
Tidskriftsartikel (refereegranskat)abstract
- Stability to the type-I edge localized mode (ELM) in JET plasmas was investigated numerically by analyzing the stability to a peeling-ballooning mode with the effects of plasma rotation and ion diamagnetic drift. The numerical analysis was performed by solving the extended Frieman-Rotenberg equation with the MINERVA-DI code. To take into account these effects in the stability analysis self-consistently, the procedure of JET equilibrium reconstruction was updated to include the profiles of ion temperature and toroidal rotation, which are determined based on the measurement data in experiments. With the new procedure and MINERVA-DI, it was identified that the stability analysis including the rotation effect can explain the ELM trigger condition in JET with ITER like wall (JET-ILW), though the stability in JET with carbon wall (JET-C) is hardly affected by rotation. The key difference is that the rotation shear in JET-ILW plasmas analyzed in this study is larger than that in JET-C ones, the shear which enhances the dynamic pressure destabilizing a peeling-ballooning mode. In addition, the increase of the toroidal mode number of the unstable MHD mode determining the ELM trigger condition is also important when the plasma density is high in JET-ILW. Though such modes with high toroidal mode number are strongly stabilized by the ion diamagnetic drift effect, it was found that plasma rotation can sometimes overcome this stabilizing effect and destabilizes the peeling-ballooning modes in JET-ILW.
|
|
| 3. |
- Alhassan, E., et al.
(författare)
-
Bayesian updating for data adjustments and multi-level uncertainty propagation within Total Monte Carlo
- 2020
-
Ingår i: Annals of Nuclear Energy. - : PERGAMON-ELSEVIER SCIENCE LTD. - 0306-4549 .- 1873-2100. ; 139
-
Tidskriftsartikel (refereegranskat)abstract
- In this work, a method is proposed for combining differential and integral benchmark experimental data within a Bayesian framework for nuclear data adjustments and multi-level uncertainty propagation, using the Total Monte Carlo method. First, input parameters to basic nuclear physics models implemented within the TALYS code, were randomly varied to produce a large set of random nuclear data files. Next, a probabilistic data assimilation was carried out by computing the likelihood function for each random nuclear data file based first on only differential experimental data and then on integral benchmark data. The individual likelihood functions from the two updates were then combined into a global likelihood function. The proposed method was applied for the adjustment of n+Pb-208 in the fast energy region below 20 MeV. The adjusted file was compared with available experimental data as well as evaluations from the major nuclear data libraries and found to compare favourably.
|
|
| 4. |
- Alhassan, Erwin, et al.
(författare)
-
Reducing A Priori 239Pu Nuclear Data Uncertainty In The Keff Using A Set Of Criticality Benchmarks With Different Nuclear Data Libraries
- 2015
-
Konferensbidrag (övrigt vetenskapligt/konstnärligt)abstract
- In the Total Monte Carlo (TMC) method [1] developed at the Nuclear Research and Consultancy Group for nuclear data uncertainty propagation, model calculations are compared with differential experimental data and a specific a priori uncertainty is assigned to each model parameter. By varying the model parameters all together within model parameter uncertainties, a full covariance matrix is obtained with its off diagonal elements if desired [1]. In this way, differential experimental data serve as a constraint for the model parameters used in the TALYS nuclear reactions code for the production of random nuclear data files. These files are processed into usable formats and used in transport codes for reactor calculations and for uncertainty propagation to reactor macroscopic parameters of interest. Even though differential experimental data together with their uncertainties are included (implicitly) in the production of these random nuclear data files in the TMC method, wide spreads in parameter distributions have been observed, leading to large uncertainties in reactor parameters for some nuclides for the European Lead cooled Training Reactor [2]. Due to safety concerns and the development of GEN-IV reactors with their challenging technological goals, the present uncertainties should be reduced significantly if the benefits from advances in modelling and simulations are to be utilized fully [3]. In Ref.[4], a binary accept/reject approach and a more rigorous method of assigning file weights based on the likelihood function were proposed and presented for reducing nuclear data uncertainties using a set of integral benchmarks obtained from the International Handbook of Evaluated Criticality Safety Benchmark Experiments (ICSBEP). These methods are depended on the reference nuclear data library used, the combined benchmark uncertainty and the relevance of each benchmark for reducing nuclear data uncertainties for a particular reactor system. Since each nuclear data library normally comes with its own nominal values and covariance matrices, reactor calculations and uncertainties computed with these libraries differ from library to library. In this work, we apply the binary accept/reject approach and the method of assigning file weights based on the likelihood function for reducing a priori 239Pu nuclear data uncertainties for the European Lead Cooled Training Reactor (ELECTRA) using a set of criticality benchmarks. Prior and posterior uncertainties computed for ELECTRA using ENDF/B-VII.1, JEFF-3.2 and JENDL-4.0 are compared after including experimental information from over 10 benchmarks.[1] A.J. Koning and D. Rochman, Modern Nuclear Data Evaluation with the TALYS Code System. Nuclear Data Sheets 113 (2012) 2841-2934. [2] E. Alhassan, H. Sjöstrand, P. Helgesson, A. J. Koning, M. Österlund, S. Pomp, D. Rochman, Uncertainty and correlation analysis of lead nuclear data on reactor parameters for the European Lead Cooled Training reactor (ELECTRA). Annals of Nuclear Energy 75 (2015) 26-37. [3] G. Palmiotti, M. Salvatores, G. Aliberti, H. Hiruta, R. McKnight, P. Oblozinsky, W. Yang, A global approach to the physics validation of simulation codes for future nuclear systems, Annals of Nuclear Energy 36 (3) (2009) 355-361. [4] E. Alhassan, H. Sjöstrand, J. Duan, P. Helgesson, S. Pomp, M. Österlund, D. Rochman, A.J. Koning, Selecting benchmarks for reactor calculations: In proc. PHYSOR 2014 - The Role of Reactor Physics toward a Sustainable Future, kyoto, Japan, Sep. 28 - 3 Oct. (2014).
|
|
| 5. |
|
|
| 6. |
- Andersson Sundén, Erik, et al.
(författare)
-
An assessment of nitrogen concentrations from spectroscopic measurements in the JET and ASDEX upgrade divertor
- 2019
-
Ingår i: Nuclear Materials and Energy. - : Elsevier. - 2352-1791. ; 18, s. 147-152
-
Tidskriftsartikel (refereegranskat)abstract
- The impurity concentration in the tokamak divertor plasma is a necessary input for predictive scaling of divertor detachment, however direct measurements from existing tokamaks in different divertor plasma conditions are limited. To address this, we have applied a recently developed spectroscopic N II line ratio technique for measuring the N concentration in the divertor to a range of H-mode and L-mode plasma from the ASDEX Upgrade and JET tokamaks, respectively. The results from both devices show that as the power crossing the separatrix, P-sep, is increased under otherwise similar core conditions (e.g. density), a higher N concentration is required to achieve the same detachment state. For example, the N concentrations at the start of detachment increase from approximate to 2% to approximate to 9% as P-sep, is increased from approximate to 2.5 MW to approximate to 7 MW. These results tentatively agree with scaling law predictions (e.g. Goldston et al.) motivating a further study examining the parameters which affect the N concentration required to reach detachment. Finally, the N concentrations from spectroscopy and the ratio of D and N gas valve fluxes agree within experimental uncertainty only when the vessel surfaces are fully-loaded with N.
|
|
| 7. |
- Angioni, C., et al.
(författare)
-
Dependence of the turbulent particle flux on hydrogen isotopes induced by collisionality
- 2018
-
Ingår i: Physics of Plasmas. - : American Institute of Physics (AIP). - 1070-664X .- 1089-7674 .- 1070-6631 .- 1089-7666. ; 25:8
-
Tidskriftsartikel (refereegranskat)abstract
- The impact of the change of the mass of hydrogen isotopes on the turbulent particle flux is studied. The trapped electron component of the turbulent particle convection induced by collisionality, which is outward in ion temperature gradient turbulence, increases with decreasing thermal velocity of the isotope. Thereby, the lighter is the isotope, the stronger is the turbulent pinch, and the larger is the predicted density gradient at the null of the particle flux. The passing particle component of the flux increases with decreasing mass of the isotope and can also affect the predicted density gradient. This effect is however subdominant for usual core plasma parameters. The analytical results are confirmed by means of both quasi-linear and nonlinear gyrokinetic simulations, and an estimate of the difference in local density gradient produced by this effect as a function of collisionality has been obtained for typical plasma parameters at mid-radius. Analysis of currently available experimental data from the JET and the ASDEX Upgrade tokamaks does not show any clear and general evidence of inconsistency with this theoretically predicted effect outside the errorbars and also allows the identification of cases providing weak evidence of qualitative consistency.
|
|
| 8. |
- Angioni, C., et al.
(författare)
-
Gyrokinetic study of turbulent convection of heavy impurities in tokamak plasmas at comparable ion and electron heat fluxes
- 2017
-
Ingår i: Nuclear Fusion. - : IOP PUBLISHING LTD. - 0029-5515 .- 1741-4326. ; 57:2
-
Tidskriftsartikel (refereegranskat)abstract
- In tokamaks, the role of turbulent transport of heavy impurities, relative to that of neoclassical transport, increases with increasing size of the plasma, as clarified by means of general scalings, which use the ITER standard scenario parameters as reference, and by actual results from a selection of discharges from ASDEX Upgrade and JET. This motivates the theoretical investigation of the properties of the turbulent convection of heavy impurities by nonlinear gyrokinetic simulations in the experimentally relevant conditions of comparable ion and electron heat fluxes. These conditions also correspond to an intermediate regime between dominant ion temperature gradient turbulence and trapped electron mode turbulence. At moderate plasma toroidal rotation, the turbulent convection of heavy impurities, computed with nonlinear gyrokinetic simulations, is found to be directed outward, in contrast to that obtained by quasi-linear calculations based on the most unstable linear mode, which is directed inward. In this mixed turbulence regime, with comparable electron and ion heat fluxes, the nonlinear results of the impurity transport can be explained by the coexistence of both ion temperature gradient and trapped electron modes in the turbulent state, both contributing to the turbulent convection and diffusion of the impurity. The impact of toroidal rotation on the turbulent convection is also clarified.
|
|
| 9. |
- Angioni, C., et al.
(författare)
-
The impact of poloidal asymmetries on tungsten transport in the core of JET H-mode plasmas
- 2015
-
Ingår i: Physics of Plasmas. - : AMER INST PHYSICS. - 1070-664X .- 1089-7674. ; 22:5
-
Tidskriftsartikel (refereegranskat)abstract
- Recent progress in the understanding and prediction of the tungsten behaviour in the core of JET H-mode plasmas with ITER-like wall is presented. Particular emphasis is given to the impact of poloidal asymmetries of the impurity density. In particular, it is shown that the predicted reduction of temperature screening induced by the presence of low field side localization of the tungsten density produced by the centrifugal force is consistent with the observed tungsten behaviour in a JET discharge in H-mode baseline scenario. This provides first evidence of the role of poloidal asymmetries in reducing the strength of temperature screening. The main differences between plasma parameters in JET baseline and hybrid scenario discharges which affect the impact of poloidally asymmetric density on the tungsten radial transport are identified. This allows the conditions by which tungsten accumulation can be avoided to be more precisely defined.
|
|
| 10. |
- Appel, L. C., et al.
(författare)
-
Equilibrium reconstruction in an iron core tokamak using a deterministic magnetisation model
- 2018
-
Ingår i: Computer Physics Communications. - : ELSEVIER. - 0010-4655 .- 1879-2944. ; 223, s. 1-17
-
Tidskriftsartikel (refereegranskat)abstract
- In many tokamaks ferromagnetic material, usually referred to as an iron-core, is present in order to improve the magnetic coupling between the solenoid and the plasma. The presence of the iron core in proximity to the plasma changes the magnetic topology with consequent effects on the magnetic field structure and the plasma boundary. This paper considers the problem of obtaining the free-boundary plasma equilibrium solution in the presence of ferromagnetic material based on measured constraints. The current approach employs, a model described by O'Brien et al. (1992) in which the magnetisation currents at the iron-air boundary are represented by a set of free parameters and appropriate boundary conditions are enforced via a set of quasi-measurements on the material boundary. This can lead to the possibility of overfitting the data and hiding underlying issues with the measured signals. Although the model typically achieves good fits to measured magnetic signals there are significant discrepancies in the inferred magnetic topology compared with other plasma diagnostic measurements that are independent of the magnetic field. An alternative approach for equilibrium reconstruction in iron-core tokamaks, termed the deterministic magnetisation model is developed and implemented in EFIT++. The iron is represented by a boundary current with the gradients in the magnetisation dipole state generating macroscopic internal magnetisation currents. A model for the boundary magnetisation currents at the iron-air interface is developed using B-Splines enabling continuity to arbitrary order; internal magnetisation currents are allocated to triangulated regions within the iron, and a method to enable adaptive refinement is implemented. The deterministic model has been validated by comparing it with a synthetic 2-D electromagnetic model of JET. It is established that the maximum field discrepancy is less than 1.5 mT throughout the vacuum region enclosing the plasma. The discrepancies of simulated magnetic probe signals are accurate to within 1% for signals with absolute magnitude greater than 100 mT; in all other cases agreement is to within 1 mT. The effect of neglecting the internal magnetisation currents increases the maximum discrepancy in the vacuum region to >20 mT, resulting in errors of 5%-10% in the simulated probe signals. The fact that the previous model neglects the internal magnetisation currents (and also has additional free parameters when fitting the measured data) makes it unsuitable for analysing data in the absence of plasma current. The discrepancy of the poloidal magnetic flux within the vacuum vessel is to within 0.1 Wb. Finally the deterministic model is applied to an equilibrium force-balance solution of a JET discharge using experimental data. It is shown that the discrepancies of the outboard separatrix position, and the outer strike-point position inferred from Thomson Scattering and Infrared camera data are much improved beyond the routine equilibrium reconstruction, whereas the discrepancy of the inner strike-point position is similar.
|
|
