| 1. |
- Fenstermacher, M.E., et al.
(författare)
-
DIII-D research advancing the physics basis for optimizing the tokamak approach to fusion energy
- 2022
-
Ingår i: Nuclear Fusion. - : IOP Publishing. - 0029-5515 .- 1741-4326. ; 62:4
-
Tidskriftsartikel (refereegranskat)abstract
- DIII-D physics research addresses critical challenges for the operation of ITER and the next generation of fusion energy devices. This is done through a focus on innovations to provide solutions for high performance long pulse operation, coupled with fundamental plasma physics understanding and model validation, to drive scenario development by integrating high performance core and boundary plasmas. Substantial increases in off-axis current drive efficiency from an innovative top launch system for EC power, and in pressure broadening for Alfven eigenmode control from a co-/counter-I p steerable off-axis neutral beam, all improve the prospects for optimization of future long pulse/steady state high performance tokamak operation. Fundamental studies into the modes that drive the evolution of the pedestal pressure profile and electron vs ion heat flux validate predictive models of pedestal recovery after ELMs. Understanding the physics mechanisms of ELM control and density pumpout by 3D magnetic perturbation fields leads to confident predictions for ITER and future devices. Validated modeling of high-Z shattered pellet injection for disruption mitigation, runaway electron dissipation, and techniques for disruption prediction and avoidance including machine learning, give confidence in handling disruptivity for future devices. For the non-nuclear phase of ITER, two actuators are identified to lower the L-H threshold power in hydrogen plasmas. With this physics understanding and suite of capabilities, a high poloidal beta optimized-core scenario with an internal transport barrier that projects nearly to Q = 10 in ITER at ∼8 MA was coupled to a detached divertor, and a near super H-mode optimized-pedestal scenario with co-I p beam injection was coupled to a radiative divertor. The hybrid core scenario was achieved directly, without the need for anomalous current diffusion, using off-axis current drive actuators. Also, a controller to assess proximity to stability limits and regulate β N in the ITER baseline scenario, based on plasma response to probing 3D fields, was demonstrated. Finally, innovative tokamak operation using a negative triangularity shape showed many attractive features for future pilot plant operation.
|
|
| 2. |
- Marinucci, A., et al.
(författare)
-
Polarization constraints on the X-ray corona in Seyfert Galaxies : MCG-05-23-16
- 2022
-
Ingår i: Monthly notices of the Royal Astronomical Society. - : Oxford University Press (OUP). - 0035-8711 .- 1365-2966. ; 516:4, s. 5907-5913
-
Tidskriftsartikel (refereegranskat)abstract
- We report on the first observation of a radio-quiet active galactic nucleus (AGN) in polarized X-rays: the Seyfert 1.9 galaxy MCG-05-23-16. This source was pointed at with the Imaging X-ray Polarimetry Explorer (IXPE) starting on 2022 May 14 for a net observing time of 486 ks, simultaneously with XMM-Newton (58 ks) and NuSTAR (83 ks). A polarization degree Π smaller than 4.7 per cent (at the 99 per cent confidence level) is derived in the 2–8 keV energy range, where emission is dominated by the primary component ascribed to the hot corona. The broad-band spectrum, inferred from a simultaneous fit to the IXPE, NuSTAR, and XMM-Newton data, is well reproduced by a power law with photon index Γ = 1.85 ± 0.01 and a high-energy cutoff EC = 120 ± 15 keV. A comparison with Monte Carlo simulations shows that a lamp-post and a conical geometry of the corona are consistent with the observed upper limit, a slab geometry is allowed only if the inclination angle of the system is less than 50°.
|
|
| 3. |
- Baumgartner, J., et al.
(författare)
-
Fatigue strength assessment of TIG-dressed welded steel joints by local approaches
- 2019
-
Ingår i: International Journal of Fatigue. - : Elsevier Ltd. - 0142-1123 .- 1879-3452. ; 126, s. 72-78
-
Tidskriftsartikel (refereegranskat)abstract
- Fatigue strength assessment methods by local approaches are widely used in the literature. This paper provides a comprehensive evaluation of published data for welded steel joints improved by TIG dressing methods. Fatigue classes for the local assessment methods with the available fatigue data are recommended. The available fatigue data extracted for transverse non-load carrying welds, cruciform joints as well as butt joints. In total, 17 published test series of weld details with various yield strengths and stress ratios are presented. Fatigue strength assessment is performed by considering the weld profile geometry within Finite Element models and taking the resulting stress gradients as basis for the evaluation. In addition, the influence of the steel grade is included. The most reliable results are derived by using the critical distance approach. Fatigue classes and critical distances are recommended as a result of the evaluations.
|
|
| 4. |
- Laptev, Ivan, et al.
(författare)
-
Automatic extraction of roads from aerial images based on scale space and snakes
- 2000
-
Ingår i: Machine Vision and Applications. - : Springer. - 0932-8092 .- 1432-1769. ; 12:1, s. 23-31
-
Tidskriftsartikel (refereegranskat)abstract
- We propose a new approach for automatic road extraction from aerial imagery with a model and a strategy mainly based on the multi-scale detection of roads in combination with geometry-constrained edge extraction using snakes. A main advantage of our approach is, that it allows for the first time a bridging of shadows and partially occluded areas using the heavily disturbed evidence in the image. Additionally, it has only few parameters to be adjusted. The road network is constructed after extracting crossings with varying shape and topology. We show the feasibility of the approach not only by presenting reasonable results but also by evaluating them quantitatively based on ground truth.
|
|
