| 1. |
- Liu, Johan, 1960, et al.
(författare)
-
1. Thermal Characterization of Power Devices Using Graphene-based Film
- 2014
-
Ingår i: Proceedings - Electronic Components and Technology Conference. - 0569-5503. - 9781479924073 ; , s. 459 - 463
-
Konferensbidrag (refereegranskat)abstract
- Due to its atomic structure with sp2 hybrid orbitals and unique electronic properties, graphene has an extraordinarily high thermal conductivity which has been reported to be up to 5000 W/mK. As a consequence, the use of graphene-based materials for thermal management has been subject to substantial attention during recent years in both academia and industry. In this paper, the development of a new type of graphene-based thin film for heat dissipation in power devices is presented. The surface of the developed graphene based film is primarily composed of functionalized graphene oxide, that can be bonded chemically to the device surface and thus minimize the interface thermal resistance caused by surface roughness. A very high in-plane thermal conductivity with a maximum value of 1600 W/mK was detected by laser flash machine regarding to the graphene-based films. To investigate the structure of the graphene-based films, scanning electron microscopy (SEM) and raman spectroscopy were carried out. Finally, LED demonstrators were built to illustrate the thermal performance of graphene-based film and the functional layers. IR camera recorded a 5°C lower temperature of a LED demonstrator with SHT G1000 as the binding layer instead of a commercial thermal conductive adhesive.
|
|
| 2. |
- Fu, Yifeng, 1984, et al.
(författare)
-
Graphene related materials for thermal management
- 2020
-
Ingår i: 2D Materials. - : IOP Publishing. - 2053-1583. ; 7:1
-
Tidskriftsartikel (refereegranskat)abstract
- Almost 15 years have gone ever since the discovery of graphene as a single atom layer. Numerous papers have been published to demonstrate its high electron mobility, excellent thermal and mechanical as well as optical properties. We have recently seen more and more applications towards using graphene in commercial products. This paper is an attempt to review and summarize the current status of the research of the thermal properties of graphene and other 2D based materials including the manufacturing and characterization techniques and their applications, especially in electronics and power modules. It is obvious from the review that graphene has penetrated the market and gets more and more applications in commercial electronics thermal management context. In the paper, we also made a critical analysis of how mature the manufacturing processes are; what are the accuracies and challenges with the various characterization techniques and what are the remaining questions and issues left before we see further more applications in this exciting and fascinating field.
|
|
| 3. |
- Han, H. X., et al.
(författare)
-
Functionalization mediates heat transport in graphene nanoflakes
- 2016
-
Ingår i: Nature Communications. - : Springer Science and Business Media LLC. - 2041-1723 .- 2041-1723. ; 7
-
Tidskriftsartikel (refereegranskat)abstract
- The high thermal conductivity of graphene and few-layer graphene undergoes severe degradations through contact with the substrate. Here we show experimentally that the thermal management of a micro heater is substantially improved by introducing alternative heat-escaping channels into a graphene-based film bonded to functionalized graphene oxide through amino-silane molecules. Using a resistance temperature probe for in situ monitoring we demonstrate that the hotspot temperature was lowered by similar to 28 degrees C for a chip operating at 1,300 Wcm(-2). Thermal resistance probed by pulsed photothermal reflectance measurements demonstrated an improved thermal coupling due to functionalization on the graphene-graphene oxide interface. Three functionalization molecules manifest distinct interfacial thermal transport behaviour, corroborating our atomistic calculations in unveiling the role of molecular chain length and functional groups. Molecular dynamics simulations reveal that the functionalization constrains the cross-plane phonon scattering, which in turn enhances in-plane heat conduction of the bonded graphene film by recovering the long flexural phonon lifetime.
|
|
| 4. |
- Huang, Shirong, et al.
(författare)
-
Reliability of Graphene-based Films Used for High Power Electronics Packaging
- 2015
-
Ingår i: 16th International Conference on Electronic Packaging Technology, ICEPT 2015, Changsha, China, 11-14 August 2015. - 9781467379991 ; , s. 852-855
-
Konferensbidrag (refereegranskat)abstract
- Graphene-base film was fabricated with chemical conversion process, including graphene oxide (GO) prepared by Hummer's method, graphene oxide reduced with L-ascorbic acid (LAA), graphene based film deposited by vacuum filtration process. Meanwhile, the functionalization of the graphene-based film was performed to decrease the thermal interface resistance between the graphene-based film and substrate. Characterization data showed that the graphene-based film possessed high reliability after 500 hours under 85°C aging test. In summary, the graphene-based film can be a promising solution in thermal management of high power electronics.
|
|
| 5. |
- Jiang, Di, 1983, et al.
(författare)
-
A flexible and stackable 3D interconnect system using growth-engineered carbon nanotube scaffolds
- 2017
-
Ingår i: Flexible and Printed Electronics. - : IOP Publishing. - 2058-8585. ; 2:2
-
Tidskriftsartikel (refereegranskat)abstract
- One of the critical challenges for realizing flexible electronic systems for a wide range of applications is the development of materials for flexible and stackable interconnects. We propose and demonstrate a three-dimensional (3D)interconnect structure embedded in a polymeric substrate using metal-coated carbon nanotube (CNT)scaffolds. By using two different underlayer materials for the catalyst, onestep synthesis of a dual-height CNT interconnect scaffold was realized. The CNT scaffolds serve as flexible cores for both annular metal through-substrate-vias and for horizontal metal interconnect. The 3D-CNT network was fabricated on a silicon substrate, and once the scaffolds were covered by metal, they were embedded in a polymer serving as a flexible substrate after peel-off from the silicon substrate. The 3D-CNT interconnect network was exposed to mechanical bending and stretching tests while monitoring its electrical properties. Even after 300 cycles no significant increase of resistances was found. Electrically there is a trade-off between flexibility and conductivity due to the surface roughness of the scaffold. However, this is to some extent alleviated by the metalized sidewalls giving the horizontal wires a cross-sectional area larger than indicated by their footprint. For gold wires 200 nm thick, measurements indicated a resistivity of 18 μΩ.cm, a value less than one order of magnitude larger than that of bulk gold, and a value that is expected to improve as technology improves. The mechanical properties of the metalized scaffolds were simulated using a finite element model. The potential scale-up capability of the proposed 3D-CNT network was demonstrated by the stacking of two such polymer-embedded interconnect systems.
|
|
| 6. |
- Jiang, Di, 1983, et al.
(författare)
-
Embedded Fin-Like Metal/CNT Hybrid Structures for Flexible and Transparent Conductors
- 2016
-
Ingår i: Small. - : Wiley. - 1613-6810 .- 1613-6829. ; 12:11, s. 1521-1526
-
Tidskriftsartikel (refereegranskat)abstract
- In this paper, an embedded fin-like metal-coated carbon nanotube (Fin-M/CNT) structure is demonstrated for flexible and transparent conductor wire applications. Embedded in a polydimethylsiloxane polymeric substrate, Fin-M/CNT wires with a minimum width of 5 μm and a minimum pitch of 10 μm have been achieved. Direct current resistances of single Fin-M/CNT wires, where the supporting CNT structures have been covered by Ti/Al/Au metal coatings of different thicknesses, have been measured. The high aspect ratio of the fin-like structures not only improves the adhesion between the wires and the polymeric substrate, but also yields a low resistance at a small surface footprint. In addition, transparent Fin-M/CNT grid lines with hexagonal patterns, with a sheet resistance of as low as 45 Ω sq−1, have been achieved at an optical transmittance of 88%. The robustness of the Fin-M/CNT structures has been demonstrated in bending tests up to 500 cycles and no significant changes in wire resistances are observed.
|
|
| 7. |
- Liu, Ya, 1991, et al.
(författare)
-
Graphene based thermal management system for battery cooling in electric vehicles
- 2020
-
Ingår i: Proceedings - 2020 IEEE 8th Electronics System-Integration Technology Conference, ESTC 2020.
-
Konferensbidrag (refereegranskat)abstract
- In this work, a graphene assembled film integrated heat sink and water cooling technology was used to build an experimental set-up of a thermal management system to demonstrate the possibility to achieve efficient cooling of the propulsion battery in electric vehicles. The experimental results showed that the temperature decrease of a Li-ion battery module can reach 11°C and 9 °C under discharge rates as of 2C and 1C, respectively. The calculated thermal resistance of the graphene based cooling system is about 76% of a similar copper based cooling system. Surface modification was carried out on the graphene sheet to achieve a reliable bonding between the graphene sheet and the battery cell surface. This work provides a proof of concept of a new highly efficient approach for electric vehicle battery thermal management using the light-weight material graphene.
|
|
| 8. |
- Nylander, Andreas, 1988, et al.
(författare)
-
RF properties of carbon nanotube / Copper composite through silicon via based CPW structure for 3D integrated circuits
- 2019
-
Ingår i: 2019 IEEE 14th Nanotechnology Materials and Devices Conference, NMDC 2019.
-
Konferensbidrag (refereegranskat)abstract
- The development of integrated circuits (ICs) has seen exponential growth in performance over the last couple of decades and has pushed the boundaries for how we use our electronics in our daily lives. The scaling of ICs, and therefore also the performance development, is now starting to slow down when the physical designs are reaching critical dimensions where quantum effects starts to become noticeable. One proposed route to circumvent these issues for a continued scaling is based on the implementation of 3D integration by chip stacking for an increased miniaturization potential. Miniaturisation will soon also result in interconnect dimensions that surpass the mean free path (MFP) in Cu, the commonly used material for interconnects today, with a sharp increase in resistivity as a result. By changing the through silicon via (TSV) interconnect material from Cu to a carbon nanotube (CNT)/Cu composite, continued scaling can be ensured both in terms of electrical conductivity, ampacity and signal delays. Furthermore, a reduced skin effect can be achieved ensuring lower signal losses at higher RF frequencies making the CNT/Cu composite an ideal candidate to replace tranditional Cu interconnects. In this paper, we are demonstrating a coplanar waveguide (CPW) test structure using CNT/Cu filled TSVs connected to Au transmission lines on SiO2-passivated high resistivity Si substrates. The parasitic losses of the CNT/Cu TSV based CPW test structure were measured using a Sparameters test setup. The results showed that the CNT/Cu TSVs with affiliated contacts increased the signal losses up to S21 = -5.5 dB compared to Au reference transmission lines. These results are in line with previous results using CNT based TSVs and will serve as a basis for future improvements of CNT based interconnect technology for 3D integration.
|
|
| 9. |
- Sun, Shuangxi, 1986, et al.
(författare)
-
Heat dissipation of a hybrid CNT/Graphene based heat spreader
- 2016
-
Ingår i: IMAPS Nordic Annual Conference 2016, Tonsberg, Norway, 5-7 June 2016. - 9781510827226
-
Konferensbidrag (refereegranskat)abstract
- Graphene and Carbon Nanotube have been received much attention in the microelectronics application, due to their intrinsic unique performance in the thermal and electronic conduction. In this paper, a free standing three dimensional (3D) carbon nanotube (CNT)/graphene (G) hybrid material was synthesized through chemical vapor deposition (CVD) process for heat dissipation application. Scanning electron microscope (SEM) was employed to characterize the morphology of this hybrid material. Thermal test chip was designed and fabricated to test the cooling effect of this CNT/G hybrid material. The temperature of the hot spot on the chip can decreased around 10 oC with the help of this hybrid material.
|
|
| 10. |
- Wang, Nan, 1988, et al.
(författare)
-
Flexible Multifunctionalized Carbon Nanotubes-Based Hybrid Nanowires
- 2015
-
Ingår i: Advanced Functional Materials. - : Wiley. - 1616-3028 .- 1616-301X. ; 25:26, s. 4135-4143
-
Tidskriftsartikel (refereegranskat)abstract
- In this work, flexible multifunctionalized carbon nanotube (CNT)-based hybrid nanowires are synthesized through surface modification processes. The good dispersability of the hybrid nanowire in polar solvents facilitates directly making fine patterns with a minimum width of 40 μm for applications of flexible and stretchable circuits (FSCs). The hybrid nanowire possesses a flexible and highly conductive structure which demonstrates stable electro-mechanical properties on polydimethylsiloxane (PDMS) substrates under large structural deformation. FSCs fabricated from the hybrid nanowires show a constant resistance of 0.096 Ω □-1 (equivalent of a resistivity 0.96 Ω μm) under repeated bending cycles. The FSCs also have a low and stable sheet resistance of 0.4 Ω □-1 for strains up to 30%, which is almost four orders of magnitude lower than that of pure CNT samples (1316 Ω □-1). Further improved stretchability and electro-mechanical properties (0.1 Ω □-1, at the strain of 100%) are achieved with a prestrain PDMS substrate. Repeated deformation tests demonstrate the high reliability of FSCs. The observed stable and reliable electro-mechanical performance of FSCs suggests the potential use of the material in wearable and portable electronics. Multifunctionalized hybrid nanowires based on carbon nanotubes are prepared through different surface modification processes. These hybrid nanowires exhibit both the high electrical conductivity of metal and excellent mechanical properties of carbon nanotubes together with good dispersability. Flexible and stretchable electrodes based on the hybrid nanowires demonstrate stable electro-mechanical properties under large structural deformations.
|
|
