| 1. |
- Fenstermacher, M.E., et al.
(author)
-
DIII-D research advancing the physics basis for optimizing the tokamak approach to fusion energy
- 2022
-
In: Nuclear Fusion. - : IOP Publishing. - 0029-5515 .- 1741-4326. ; 62:4
-
Journal article (peer-reviewed)abstract
- DIII-D physics research addresses critical challenges for the operation of ITER and the next generation of fusion energy devices. This is done through a focus on innovations to provide solutions for high performance long pulse operation, coupled with fundamental plasma physics understanding and model validation, to drive scenario development by integrating high performance core and boundary plasmas. Substantial increases in off-axis current drive efficiency from an innovative top launch system for EC power, and in pressure broadening for Alfven eigenmode control from a co-/counter-I p steerable off-axis neutral beam, all improve the prospects for optimization of future long pulse/steady state high performance tokamak operation. Fundamental studies into the modes that drive the evolution of the pedestal pressure profile and electron vs ion heat flux validate predictive models of pedestal recovery after ELMs. Understanding the physics mechanisms of ELM control and density pumpout by 3D magnetic perturbation fields leads to confident predictions for ITER and future devices. Validated modeling of high-Z shattered pellet injection for disruption mitigation, runaway electron dissipation, and techniques for disruption prediction and avoidance including machine learning, give confidence in handling disruptivity for future devices. For the non-nuclear phase of ITER, two actuators are identified to lower the L-H threshold power in hydrogen plasmas. With this physics understanding and suite of capabilities, a high poloidal beta optimized-core scenario with an internal transport barrier that projects nearly to Q = 10 in ITER at ∼8 MA was coupled to a detached divertor, and a near super H-mode optimized-pedestal scenario with co-I p beam injection was coupled to a radiative divertor. The hybrid core scenario was achieved directly, without the need for anomalous current diffusion, using off-axis current drive actuators. Also, a controller to assess proximity to stability limits and regulate β N in the ITER baseline scenario, based on plasma response to probing 3D fields, was demonstrated. Finally, innovative tokamak operation using a negative triangularity shape showed many attractive features for future pilot plant operation.
|
|
| 2. |
- Reimerdes, H., et al.
(author)
-
Overview of the TCV tokamak experimental programme
- 2022
-
In: Nuclear Fusion. - : IOP Publishing. - 1741-4326 .- 0029-5515. ; 62:4
-
Journal article (peer-reviewed)abstract
- The tokamak a configuration variable (TCV) continues to leverage its unique shaping capabilities, flexible heating systems and modern control system to address critical issues in preparation for ITER and a fusion power plant. For the 2019-20 campaign its configurational flexibility has been enhanced with the installation of removable divertor gas baffles, its diagnostic capabilities with an extensive set of upgrades and its heating systems with new dual frequency gyrotrons. The gas baffles reduce coupling between the divertor and the main chamber and allow for detailed investigations on the role of fuelling in general and, together with upgraded boundary diagnostics, test divertor and edge models in particular. The increased heating capabilities broaden the operational regime to include T (e)/T (i) similar to 1 and have stimulated refocussing studies from L-mode to H-mode across a range of research topics. ITER baseline parameters were reached in type-I ELMy H-modes and alternative regimes with 'small' (or no) ELMs explored. Most prominently, negative triangularity was investigated in detail and confirmed as an attractive scenario with H-mode level core confinement but an L-mode edge. Emphasis was also placed on control, where an increased number of observers, actuators and control solutions became available and are now integrated into a generic control framework as will be needed in future devices. The quantity and quality of results of the 2019-20 TCV campaign are a testament to its successful integration within the European research effort alongside a vibrant domestic programme and international collaborations.
|
|
| 3. |
- Komatsu, Kimberly J., et al.
(author)
-
Global change effects on plant communities are magnified by time and the number of global change factors imposed
- 2019
-
In: Proceedings of the National Academy of Sciences of the United States of America. - : National Academy of Sciences. - 0027-8424 .- 1091-6490. ; 116:36, s. 17867-17873
-
Journal article (peer-reviewed)abstract
- Accurate prediction of community responses to global change drivers (GCDs) is critical given the effects of biodiversity on ecosystem services. There is consensus that human activities are driving species extinctions at the global scale, but debate remains over whether GCDs are systematically altering local communities worldwide. Across 105 experiments that included over 400 experimental manipulations, we found evidence for a lagged response of herbaceous plant communities to GCDs caused by shifts in the identities and relative abundances of species, often without a corresponding difference in species richness. These results provide evidence that community responses are pervasive across a wide variety of GCDs on long-term temporal scales and that these responses increase in strength when multiple GCDs are simultaneously imposed.Global change drivers (GCDs) are expected to alter community structure and consequently, the services that ecosystems provide. Yet, few experimental investigations have examined effects of GCDs on plant community structure across multiple ecosystem types, and those that do exist present conflicting patterns. In an unprecedented global synthesis of over 100 experiments that manipulated factors linked to GCDs, we show that herbaceous plant community responses depend on experimental manipulation length and number of factors manipulated. We found that plant communities are fairly resistant to experimentally manipulated GCDs in the short term (<10 y). In contrast, long-term (≥10 y) experiments show increasing community divergence of treatments from control conditions. Surprisingly, these community responses occurred with similar frequency across the GCD types manipulated in our database. However, community responses were more common when 3 or more GCDs were simultaneously manipulated, suggesting the emergence of additive or synergistic effects of multiple drivers, particularly over long time periods. In half of the cases, GCD manipulations caused a difference in community composition without a corresponding species richness difference, indicating that species reordering or replacement is an important mechanism of community responses to GCDs and should be given greater consideration when examining consequences of GCDs for the biodiversity–ecosystem function relationship. Human activities are currently driving unparalleled global changes worldwide. Our analyses provide the most comprehensive evidence to date that these human activities may have widespread impacts on plant community composition globally, which will increase in frequency over time and be greater in areas where communities face multiple GCDs simultaneously.
|
|
| 4. |
- Peng, Wenhong, et al.
(author)
-
Over 18% ternary polymer solar cells enabled by a terpolymer as the third component
- 2022
-
In: Nano Energy. - : Elsevier BV. - 2211-2855. ; 92
-
Journal article (peer-reviewed)abstract
- “Ternary blending” and “random terpolymerization” strategies have both proven effective for enhancing the performance of organic solar cells (OSCs). However, reports on the combination of the two strategies remain rare. Here, a terpolymer PM6-Si30 was constructed by inserting chlorine and alkylsilyl-substituted benzodithiophene (BDT) unit (0.3 equivalent) into the state-of-the-art polymer PM6. The terpolymer exhibitsadeep highest-occupied-molecular-orbital energy and good miscibility with both PM6 and BTP-eC9 (C9) and enables its use as a third component into PM6:PM6-Si30:C9 bulk-heterojunction for OSCs. The resulting cells exhibit maximum power conversion efficiency (PCE) of 18.27%, which is higher than that obtained for the optimized control binary PM6:C9-based OSC (17.38%). The enhanced performance of the PM6:PM6-Si30:C9 cells is attributed to improved charge transport, favorable molecular arrangement, reduced energy loss and suppressed bimolecular recombination. The work demonstrates the potential of random terpolymer as a third component in OSCs and highlights a new strategy for the construction of a ternary system with improved photovoltaic performance.
|
|
| 5. |
- Lu, P. F., et al.
(author)
-
Strain induced composition profile in InGaN/GaN core-shell nanowires
- 2014
-
In: Solid State Communications. - : Elsevier BV. - 0038-1098. ; 178, s. 1-6
-
Journal article (peer-reviewed)abstract
- A theoretical investigation on explanation of the composition profile in triangular and hexagonal cross-sections of InGaN/GaN core-shell nanowires is presented by combining the finite elements method (FEM) and method of moving asymptotes (MMA) in the framework of thermodynamics. Our models can account for strain effect on indium composition. In both models, the maximum indium content through segregation arises either at the side length or at the corner of the InGaN shell. The simulated results are found in good agreement with those of experimental data, thus providing a good guidance for the growth of high indium concentration of InGaN/GaN core-shell nanowires.
|
|
| 6. |
- Fernando, W. Primal D., et al.
(author)
-
The Solubility of Propane (R290) with Commonly Used Compressor Lubrication Oils
- 2003
-
In: Compressors and Their Systems. - 1860584179 ; , s. 157-166
-
Conference paper (peer-reviewed)abstract
- An ongoing project called "Charge minimisation of a small capacity heat pump" is aimed to minimise the refrigerant charge in heat pumps, refrigeration and air-conditioning systems. The experimental heat pump was run with propane as refrigerant and the designed heat capacity (condenser capacity) was over 5kW. Tests were done to investigate the refrigerant charge distribution in different sections of the heat pump, while it was running. The experiments done so far have shown that the amount of refrigerant in the compressor is higher than expected. This paper presents the measured refrigerant masses in a hermetic scroll compressor together in suction line and the calculated refrigerant mass dissolved in the compressor lubrication oil at different evaporation temperatures. Finally, solubility tests of propane with different lubricating oils are presented. The tests show that the propane is more soluble in POE than PAG oils.
|
|
| 7. |
- Han, S. -W, et al.
(author)
-
Distributed power allocation for cooperative access in cognitive radios to guarantee QoS for cell edge primary users
- 2013
-
In: Proceedings of 2013 6th Joint IFIP Wireless and Mobile Networking Conference, WMNC 2013. - New York : IEEE. - 9781467356169 ; , s. 6549027-
-
Conference paper (peer-reviewed)abstract
- Cognitive radio (CR) systems have been proposed for efficient usage of spare spectrum licensed to primary systems. This leads to the issue of providing as much spectrum to CR users as possible while not degrading the quality of service (QoS) of primary users of the spectrum. This paper proposes a novel cooperation scheme between primary and CR users to guarantee QoS of primary users up to the cell edge while making the licensed spectrum available for opportunistic access by the CR users. We suggest that the primary users at the cell edge, who have poor QoS, should allow secondary users to access their spectrum, while at the same time, the secondary users would help to enhance the primary users QoS using superposition coding on the primary users transmissions. Thus the proposed method can provide a so called 'win-win strategy' by benefiting both primary and CR users. The proposed cooperative access scheme in cognitive radios solves efficiently the sum-rate maximization problem on cognitive Gaussian Multiple Access Channels (GMACs) for power allocation of primary systems that cooperates with CR systems in a distributed fashion. We solved the problem using iterative Jacobian method in a distributed manner. Numerical results show that the QoS of primary users at the cell edge is improved by the proposed cooperative access scheme.
|
|
| 8. |
- Tommasini, R., et al.
(author)
-
Accepted Tutorials at The Web Conference 2022
- 2022
-
In: WWW 2022 - Companion Proceedings of the Web Conference 2022. - New York, NY, USA : Association for Computing Machinery (ACM). ; , s. 391-399
-
Conference paper (peer-reviewed)abstract
- This paper summarizes the content of the 20 tutorials that have been given at The Web Conference 2022: 85% of these tutorials are lecture style, and 15% of these are hands on.
|
|
| 9. |
- Wopereis, Han, et al.
(author)
-
Multimodal Aerial Locomotion : An Approach to Active Tool Handling 10 Author
- 2018
-
In: IEEE robotics & automation magazine. - Piscataway, NJ : IEEE. - 1070-9932 .- 1558-223X. ; 25:4, s. 57-65
-
Journal article (peer-reviewed)abstract
- The research focus in aerial robotics is shifting from contactless inspection toward interaction and manipulation, with the number of potential applications rapidly increasing [1]. Eventually, aerial manipulators, i.e., unmanned aerial vehicles (UAVs) equipped with manipulators, will likely take on hazardous maintenance tasks now performed by humans. For this to happen, aerial manipulators must be able to perform all the different operations required in these maintenance routines.
|
|
| 10. |
- Fu, L., et al.
(author)
-
Microstructure and tribological properties of Cr3C2/Ni3Al composite materials prepared by hot isostatic pressing (HIP)
- 2017
-
In: Materials and Design. - : Elsevier BV. - 1873-4197 .- 0264-1275. ; 115:115, s. 203-212
-
Journal article (peer-reviewed)abstract
- Ni3Al-based composites with different Cr3C2 contents were fabricated by the hot isostatic pressing (HIP) technique.The microstructure, phase constitution, and tribological properties of the composites were investigated by scanning electron microscopy (SEM), energy dispersive spectroscopy (EDS), X-ray diffraction (XRD), transmission electron microscopy (TEM), and pin-on-disk wear tests. The results revealed that the strengthening phase is distributed homogeneously in the Ni3Al matrix. During the HIP process, M7C3 (M = Cr, Fe) is formed by diffusion of Fe, C, and Cr to the interface between the Cr3C2 particles and Ni3Al matrix. The diffusion process binds the phases and is important for improving the wear resistance of Cr3C2/Ni3Al composites. The wear measurements demonstrated that micro-cutting and fatigue wear are the dominant mechanisms for this tribological pair. The wear resistance of Cr3C2/Ni3Al composites is significantly improved by the addition of Cr3C2 particles.When the content of Cr3C2 is within a certain range, the wear resistance of Cr3C2/Ni3Al composites increases as the Cr3C2 content increases. However, the addition of excess Cr3C2 (for example, 24 vol% in this work) could lead to a decrease in the wear resistance of the composites. In addition, the average friction coefficients and wear of the counterpart decrease with increasing Cr3C2 addition.
|
|
