| 1. |
- Briscoe, W. J., et al.
(författare)
-
Nuclear physics program at MAX-lab
- 2009
-
Ingår i: Chinese Physics C. - : IOP Publishing. - 0899-9996 .- 1674-1137. ; 33:12, s. 1159-1166
-
Konferensbidrag (refereegranskat)abstract
- The upgrade of the MAX-lab Injector and the construction of MAX III, provided the opportunity for upgrading the tagged-photon facility and thus lead to the possibility of more extensive program in nuclear physics research This upgrade increased the injected electron energy to all eventual maximum of 250 MeV and allows for the extraction of electrons from the MAX I ring operated in the stretcher mode The first stretched bean was delivered in September 2005. The tagged-photon facility was commissioned in parallel with the commissioning of new experimental equipment. The PAC approved experimental program is current in progress, including measurement of pion photoproduction below the Delta(1232) The efforts at the tagged photon-facility are pursed within all international collaboration with around fifty members
|
|
| 2. |
- Feldman, G., et al.
(författare)
-
Compton scattering from deuterium and the polarizabilities of the neutron
- 2008
-
Ingår i: Few-Body Systems. - : Springer Science and Business Media LLC. - 0177-7963 .- 1432-5411. ; 44:1-4, s. 325-328
-
Konferensbidrag (refereegranskat)abstract
- A new program of Compton scattering on deuterium is under way at the tagged-photon facility at MAX-Lab in Lund, Sweden. We will measure differential cross sections between 60A degrees and 150A degrees over the photon energy range 60-115 MeV in 5 MeV steps, with the ultimate goal of obtaining new precision information on the electric and magnetic polarizabilities of the neutron.
|
|
| 3. |
- Fissum, Kevin, et al.
(författare)
-
The Coherent Bremsstrahlung Beam at MAX-lab Facility
- 2008
-
Ingår i: Charged and Neutral Particles Channeling Phenomena Channeling 2008 : Proceedings of the 51st Workshop of the INFN ELOISATRON Project - Proceedings of the 51st Workshop of the INFN ELOISATRON Project. - : WORLD SCIENTIFIC. ; , s. 49-61
-
Konferensbidrag (refereegranskat)abstract
- The linearly polarized photon beam for photonuclear researches has been produced at MAX-lab facility on the base of coherent bremsstrahlung process of electrons in a diamond crystal. Test experiments have been performed at electron energies 143.9 and 192.7 MeV with a diamond crystal 0.1 mm thick. The measured coherent bremsstrahlung spectra demonstrate typical features to be observed at higher electron energies. The polarization ~35% was obtained at coherent peak energy of ~60 MeV. The experiments have shown that produced polarized photon beam can be used for photonuclear investigations at energy range up to 60 MeV. To extend the energy range it is necessary to increase maximal energy of the electron beam up to 250 MeV.
|
|
| 4. |
|
|
| 5. |
|
|
| 6. |
- Svennberg, Kaisa, et al.
(författare)
-
Moisture penetration in a chair seat as a response to daily RH variations in the indoor air
- 2005
-
Ingår i: [Host publication title missing]. - 9979917466
-
Konferensbidrag (refereegranskat)abstract
- In the indoor environment there are a number of materials with potential to act as moisture buffers including both building materials and furnishing materials. For daily moisture variations in the indoor air furniture with upholstery can play an important role as moisture buffers. Material properties and calculation models describing the response to moisture variations in the ambient climate for these material combinations are limited. In this project the moisture properties for a chair seat with a wool fabric and plastic foam padding were determined. The moisture penetration in the chair seat was measured using small temperature and relative humidity sensors. A numerical calculation model describing the step-response as well as the response to ramp variations is described. A comparison between measurements and theoretical calculations was performed. The difficulties with determination of material properties for highly permeable materials are also discussed as well as suitable methods and special considerations.
|
|
