| 1. |
-
- 2018
-
Ingår i: Nuclear Fusion. - : IOP Publishing. - 1741-4326 .- 0029-5515. ; 58:1
-
Forskningsöversikt (refereegranskat)
|
|
| 2. |
|
|
| 3. |
- Joffrin, E., et al.
(författare)
-
Overview of the JET preparation for deuterium-tritium operation with the ITER like-wall
- 2019
-
Ingår i: Nuclear Fusion. - : IOP Publishing. - 1741-4326 .- 0029-5515. ; 59:11
-
Forskningsöversikt (refereegranskat)abstract
- For the past several years, the JET scientific programme (Pamela et al 2007 Fusion Eng. Des. 82 590) has been engaged in a multi-campaign effort, including experiments in D, H and T, leading up to 2020 and the first experiments with 50%/50% D-T mixtures since 1997 and the first ever D-T plasmas with the ITER mix of plasma-facing component materials. For this purpose, a concerted physics and technology programme was launched with a view to prepare the D-T campaign (DTE2). This paper addresses the key elements developed by the JET programme directly contributing to the D-T preparation. This intense preparation includes the review of the physics basis for the D-T operational scenarios, including the fusion power predictions through first principle and integrated modelling, and the impact of isotopes in the operation and physics of D-T plasmas (thermal and particle transport, high confinement mode (H-mode) access, Be and W erosion, fuel recovery, etc). This effort also requires improving several aspects of plasma operation for DTE2, such as real time control schemes, heat load control, disruption avoidance and a mitigation system (including the installation of a new shattered pellet injector), novel ion cyclotron resonance heating schemes (such as the three-ions scheme), new diagnostics (neutron camera and spectrometer, active Alfven eigenmode antennas, neutral gauges, radiation hard imaging systems...) and the calibration of the JET neutron diagnostics at 14 MeV for accurate fusion power measurement. The active preparation of JET for the 2020 D-T campaign provides an incomparable source of information and a basis for the future D-T operation of ITER, and it is also foreseen that a large number of key physics issues will be addressed in support of burning plasmas.
|
|
| 4. |
|
|
| 5. |
|
|
| 6. |
- Huber, A., et al.
(författare)
-
Comparative H-mode density limit studies in JET and AUG
- 2017
-
Ingår i: Nuclear Materials and Energy. - : Elsevier. - 2352-1791. ; 12, s. 100-110
-
Forskningsöversikt (refereegranskat)abstract
- Identification of the mechanisms for the H-mode density limit in machines with fully metallic walls, and their scaling to future devices is essential to find for these machines the optimal operational boundaries with the highest attainable density and confinement. Systematic investigations of H-mode density limit plasmas in experiments with deuterium external gas fuelling have been performed on machines with fully metallic walls, JET and AUG and results have been compared with one another. Basically, the operation phases are identical for both tokamaks: the stable H-mode phase, degrading H-mode phase, breakdown of the H-mode with energy confinement deterioration usually accompanied by a dithering cycling phase, followed by the l -mode phase. The observed H-mode density limit on both machines is found close to the Greenwald limit (n/n GW = 0.8-1.1 in the observed magnetic configurations). The similar behavior of the radiation on both tokamaks demonstrates that the density limit (DL) is neither related to additional energy losses from the confined region by radiation, nor to an inward collapse of the hot discharge core induced by overcooling of the plasma periphery by radiation. It was observed on both machines that detachment, as well as the X-point MARFE itself, does not trigger a transition in the confinement regime and thus does not present a limit on the plasma density. It is the plasma confinement, most likely determined by edge parameters, which is ultimately responsible for the transition from H-to L-mode. The measured Greenwald fractions are found to be consistent with the predictions from different theoretical models [16,30] based on MHD instability theory in the near-SOL.
|
|
| 7. |
- Özkan, Leyla, et al.
(författare)
-
Advanced autonomous model-based operation of industrial process systems (Autoprofit) : Technological developments and future perspectives
- 2016
-
Ingår i: ANNUAL REVIEWS IN CONTROL. - : Elsevier. - 1367-5788. ; 42, s. 126-142
-
Forskningsöversikt (refereegranskat)abstract
- Model-based operation support technology such as Model Predictive Control (MPC) is a proven and accepted technology for multivariable and constrained large scale control problems in process industry. Despite the growing number of successful implementations, the low level of operational efficiency of MPC is an existing problem, specifically the lack of advanced maintenance technology. To this end, within the EU FP 7 program, a project (Autoprofit (1)) has been executed to advance the level of autonomy and automated maintenance of MPC technology. Taking linear model-based technology as a starting point, in the project a philosophy has been developed for autonomous performance monitoring, diagnosis, experiment design, model adaptation and controller re-tuning, that is driven by economic criteria in each step, working towards an operation support system in which effective maintenance and adaptation of MPC controllers becomes feasible. In this development, challenging research questions have been addressed in the areas of on-line performance monitoring and diagnosis, least costly experiment design, automated adaptation of models, and auto-tuning, and new fundamental techniques have been developed. Although a full fledge and industrially proven (semi-)automated system is not yet realised, parts of the on-line system have been implemented and validated on real life cases provided by the industrial partners, showing that the formulated objectives are within reach.
|
|
