SwePub
Sök i SwePub databas

  Utökad sökning

Träfflista för sökning "WFRF:(Jakobsson Mattias) ;lar1:(liu)"

Sökning: WFRF:(Jakobsson Mattias) > Linköpings universitet

  • Resultat 1-10 av 16
Sortera/gruppera träfflistan
   
NumreringReferensOmslagsbildHitta
1.
  • Andersson, Mattias, et al. (författare)
  • Intrinsic and extrinsic influences on the temperature dependence of mobility in conjugated polymers
  • 2008
  • Ingår i: Organic electronics. - : Elsevier. - 1566-1199 .- 1878-5530. ; 9:5, s. 569-574
  • Tidskriftsartikel (refereegranskat)abstract
    • The temperature dependence of charge carrier mobility in conjugated polymers and their blends with fullerenes is investigated with different electrical methods, through field effect transistor (FET), space charge limited current (SCLC) and charge extraction (CELIV) measurements. Simple models, such as the Gaussian disorder model (GDM), are shown to accurately predict the temperature behavior, and a good correlation between the different measurement methods is obtained. Inconsistent charge carrier concentrations in the modeling are explained through intrinsic non-equilibrium effects, and are responsible for the limited applicability of existing numerical models. A severe extrinsic influence from water in FETs with a hydrophilic insulator interface is also demonstrated. The presence of water leads to a significant overestimate of the disorder in the materials from measurements close to room temperature and erratic behavior in the 150-350 K range. To circumvent this problem it is shown to be necessary to measure under ultra high vacuum (UHV) conditions. © 2008 Elsevier B.V. All rights reserved.
  •  
2.
  • Cotgreave, Ian, et al. (författare)
  • Pyriproxifen and microcephaly: an investigation of potential ties to the ongoing "Zika epidemic"
  • 2016
  • Rapport (övrigt vetenskapligt/konstnärligt)abstract
    • As part of the Swetox mission to react to emerging concerns in chemical health and environmental safety, a preliminary litterature investigation was undertaken to gather all readily available scientific information on PPF with respect to safety assessment, in order to better understand potential links between chemical exposure and the devopment of microcephaly in affected areas. Therefore the contents of the report do not constitute an attempt at either questioning the use of existing regulatory data in the manner prescribed by international regulatory proceedures, or as a new risk assessment, based on the scientific information and concepts discussed. Here we report our findings, with particular emphasis on exisiting regulatory information, potential for lack of translation of results from regulatory animal testing to humans, lack of human exposure data and suggestions on plausible mode(s) of action of PPF in human neurodevelopmental adversities such as microcephaly.
  •  
3.
  • Jakobsson, Erik, et al. (författare)
  • Automated Usage Characterization of Mining Vehicles For Life Time Prediction
  • 2020
  • Ingår i: IFAC PAPERSONLINE. - : ELSEVIER. - 2405-8963. ; , s. 11950-11955
  • Konferensbidrag (refereegranskat)abstract
    • The life of a vehicle is heavily influenced by how it is used, and usage information is critical to predict the future condition of the machine. In this work we present a method to categorize what task an earthmoving vehicle is performing, based on a data driven model and a single standalone accelerometer. By training a convolutional neural network using a couple of weeks of labeled data, we show that a three axis accelerometer is sufficient to correctly classify between 5 different classes with an accuracy over 96% for a balanced dataset with no manual feature generation. The results are also compared against some other machine learning techniques, showing that the convolutional neural network has the highest performance, although other techniques are not far behind. An important conclusion is that methods and ideas from the area of Human Activity Recognition (HAR) are applicable also for vehicles. Copyright (C) 2020 The Authors.
  •  
4.
  • Jakobsson, Erik, 1987- (författare)
  • Condition Monitoring in Mobile Mining Machinery
  • 2022
  • Doktorsavhandling (övrigt vetenskapligt/konstnärligt)abstract
    • The global mining industry is currently facing a huge transition from manually operated individual vehicles, to autonomous vehicles being part of an industrial process-like environment. The change is driven by the never ending need for efficient, safe, and environmentally friendly operations. One intentional consequence is an increased distance between the operator, and the machine being operated. This enables safer working environments and reduced cost for ventilation and other supporting systems in a mine, but it also results in the loss of the systems most important sensor. The transition from manual to autonomous operation requires this gap to be filled from a system awareness perspective, which lately has become evident with the large resources that car manufacturers use to develop self-driving cars. This thesis also targets system awareness, but of the internal kind. By this we mean knowing the condition of the machine and its capabilities. The operator is the most important sensor also for internal condition, and if no operator is present on the machine, this gap needs to be filled.The mining industry is categorized by small series and significant customization of machinery. This is a direct result of the geological prerequisites, where differently shaped ore bodies cause large differences in mine layout and mining methods. This thesis explores how methods estimating the health of mining vehicles can be used in this setting, by utilizing sensor signals to make assessments of the current vehicle condition and tasks.The resulting health information can be used both to aid in tasks such as maintenance planning, but also as an important input to decision making for the planning system, i.e. how to run the vehicle for minimum wear and damage, while maintaining other mission objectives.Two applications are studied. Mine trucks have slow degradation modes, such as crack propagation and fatigue, that are difficult to handle with data driven approaches since data collection requires significant amounts of time. A contribution in this thesis, is a method to utilize short term measurement data together with data driven methods to obtain the loads of a vehicle, and then to use physics based approaches to estimate the actual damage.The second application considers monitoring faults in hydraulic rock drills using online measurements during operation. The rock drill is a specifically difficult case, since severe vibration levels limits the locations and types of sensors that can be used. The main contribution is a method to handle individual differences when classifying internal faults using a single pressure sensor on the hydraulic supply line. A complicating factor is the large influence of wave propagation, causing different individuals to show different behavior.
  •  
5.
  • Jakobsson, Erik, 1987-, et al. (författare)
  • Data driven modeling and estimation of accumulated damage in mining vehicles using on-board sensors
  • 2017
  • Ingår i: PHM 2017. Proceedings of the Annual Conference of the Prognostics and Health Management Society 2017, St. Petersburg, Florida, USA, October 2–5, 2017. - : Prognostics and Health Management Society. - 9781936263264 ; , s. 98-107
  • Konferensbidrag (refereegranskat)abstract
    • The life and condition of a MT65 mine truck frame is to a large extent related to how the machine is used. Damage from different stress cycles in the frame are accumulated over time, and measurements throughout the life of the machine are needed to monitor the condition. This results in high demands on the durability of sensors used. To make a monitoring system cheap and robust enough for a mining application, a small number of robust sensors are preferred rather than a multitude of local sensors such as strain gauges. The main question to be answered is whether a low number of robust on-board sensors can give the required information to recreate stress signals at various locations of the frame. Also the choice of sensors among many different locations and kinds are considered. A final question is whether the data could also be used to estimate road condition. By using accelerometer, gyroscope and strain gauge data from field tests of an Atlas Copco MT65 mine truck, coherence and Lasso-regression were evaluated as means to select which signals to use. ARX-models for stress estimation were created using the same data. By simulating stress signals using the models, rain flow counting and damage accumulation calculations were performed. The results showed that a low number of on-board sensors like accelerometers and gyroscopes could give enough information to recreate some of the stress signals measured. Together with a linear model, the estimated stress was accurate enough to evaluate the accumulated fatigue damage in a mining truck. The accumulated damage was also used to estimate the condition of the road on which the truck was traveling. To make a useful road monitoring system some more work is required, in particular regarding how vehicle speed influences damage accumulation.
  •  
6.
  • Jakobsson, Erik, 1987- (författare)
  • Data-driven Condition Monitoring in Mining Vehicles
  • 2019
  • Licentiatavhandling (övrigt vetenskapligt/konstnärligt)abstract
    • Situation awareness is a crucial capability of any autonomous system, including mining vehicles such as drill rigs and mine trucks. Typically situation awareness is interpreted as the capability of an autonomous system to interpret its surroundings and the intentions of other agents. The internal system awareness however, is often not receiving the same focus, even though the success of any given mission is completely dependent of the condition of the agents themselves. The internal system awareness in the form of vehicle health is the focus of this thesis.As the mining industry becomes increasingly automated, and vehicles become increasingly advanced, the need for condition monitoring and prognostics will continue to rise. This thesis explores data-driven methods that estimate the health of mining vehicles to accommodate those needs. We do so by utilizing available sensor signals, common on a large amount of mining vehicles, to make assessments of the current vehicle condition and tasks. The mining industry is characterized by small series of highly specialized vehicles, which affects the possibility to use more traditional prognostic solutions.The resulting health information can be used both to aid in tasks such as maintenance planning, but also as an important input to decision making for the planning system, i.e. how to run the vehicle for minimum wear and damage, while maintaining other mission objectives.The contributions include: a) A method to use operational data to estimate damage on the frame of a mine truck. This is done using system identification to find a model describing stresses in the structure with input from other sensors such as accelerometers, load sensors and pressure sensors. The estimated stress time signal is in turn used to calculate accumulated damage, and is shown to reveal interesting conclusions on driver behavior. b) A method to characterize the different driving tasks by using an accelerometer and a convolutional neural network. We show that the model is capable of classifying the vehicle task correctly in 96 % of the cases. And finally c), a system for underground road monitoring, where a quarter car model and a Kalman filter are used to generate an estimate of the road profile, while positioning the vehicle using inertial measurements and access point signal strength.
  •  
7.
  • Jakobsson, Erik, 1987-, et al. (författare)
  • Fatigue Damage Monitoring for Mining Vehicles using Data Driven Models
  • 2020
  • Ingår i: International Journal of Prognostics and Health Management. - Rochester, NY, United States : Prognostics and Health Management Society. - 2153-2648. ; 11:1
  • Tidskriftsartikel (refereegranskat)abstract
    • The life and condition of a mine truck frame are related to how the machine is used. Damage from stress cycles is accumulated over time, and measurements throughout the life of the machine are needed to monitor the condition. This results in high demands on the durability of sensors, especially in a harsh mining application. To make a monitoring system cheap and robust, sensors already available on the vehicles are preferred rather than additional strain gauges. The main question in this work is whether the existing on-board sensors can give the required information to estimate stress signals and calculate accumulated damage of the frame. Model complexity requirements and sensors selection are also considered. A final question is whether the accumulated damage can be used for prognostics and to increase reliability. The investigation is performed using a large data set from two vehicles operating in real mine applications. Coherence analysis, ARX-models, and rain flow counting are techniques used. The results show that a low number of available on-board sensors like load cells, damper cylinder positions, and angle transducers can give enough information to recreate some of the stress signals measured. The models are also used to show significant differences in usage by different operators, and its effect on the accumulated damage.
  •  
8.
  • Jakobsson, Erik, et al. (författare)
  • Fault Identification in Hydraulic Rock Drills from Indirect Measurement During Operation
  • 2021
  • Ingår i: IFAC PAPERSONLINE. - : ELSEVIER. - 2405-8963. ; , s. 73-78
  • Konferensbidrag (refereegranskat)abstract
    • This work presents a method for on-line condition monitoring of a hydraulic rock drill, though some of the findings can likely be applied in other applications. A fundamental difficulty for the rock drill application is discussed, namely the similarity between frequencies of internal standing waves and rock drill operation. This results in unpredictable pressure oscillations and superposition, which makes synchronization between measurement and model difficult. To overcome this, a data driven approach is proposed. The number and types of sensors are restricted due to harsh environmental conditions, and only operational data is available. Some faults are shown to be detectable using hand-crafted engineering features, with a direct physical connection to the fault of interest. Such features are easily interpreted and are shown to be robust against disturbances. Other faults are detected by classifying measured signals against a known reference. Dynamic Time Warping is shown to be an efficient way to measure similarity for cyclic signals with stochastic elements from disturbances, wave propagation and different durations, and also for cases with very small differences in measured pressure signals. Together, the two methods enables a step towards condition monitoring of a rock drill, robustly detecting very small changes in behaviour using a minimum amount of sensors. Copyright (C) 2021 The Authors.
  •  
9.
  • Jakobsson, Erik, 1987-, et al. (författare)
  • Time Series Fault Classification for Wave Propagation Systems with Sparse Fault Data
  • Annan publikation (övrigt vetenskapligt/konstnärligt)abstract
    • In this work Time Series Classification techniques are investigated, and especially their applicability in applications where there are significant differences between the individuals where data is collected, and the individuals where the classification is evaluated. Classification methods are applied to a fault classification case, where a key assumption is that data from a fault free reference case for each specific individual is available. For the investigated application, wave propagation cause almost chaotic changes of a measured pressure signal, and physical modeling is difficult. Direct application of One-Nearest-Neighbor Dynamic Time Warping, a common technique for this kind of problem, and other machine learning techniques are shown to fail for this case and new methods to improve the situation are presented. By using relative features describing the difference from the reference case rather than the absolute time series, improvements are made compared to state-of-the-art time series classification algorithms.
  •  
10.
  • Jakobsson, Mattias, et al. (författare)
  • A Monte Carlo study of charge transfer in DNA
  • 2008
  • Ingår i: Journal of Chemical Physics. - : AIP Publishing. - 0021-9606 .- 1089-7690. ; 129:12, s. 125102-
  • Tidskriftsartikel (refereegranskat)abstract
    • A model describing charge (hole) transport in DNA has been developed. The individual charge transfer steps in the transport process are described by Marcus theory modified to account for electron delocalization over adjacent identical nucleobases. Such a modification, as well as introducing a distance dependence in the reorganization energy, is necessary in order to reach an agreement with the observed transfer rates in well defined model systems to DNA. Using previously published results as a reference for the reorganization energy and with the delocalization described within the Hückel model we obtain an excellent agreement with experimental data.
  •  
Skapa referenser, mejla, bekava och länka
  • Resultat 1-10 av 16
Typ av publikation
tidskriftsartikel (7)
konferensbidrag (3)
doktorsavhandling (3)
rapport (1)
annan publikation (1)
licentiatavhandling (1)
visa fler...
visa färre...
Typ av innehåll
refereegranskat (10)
övrigt vetenskapligt/konstnärligt (6)
Författare/redaktör
Jakobsson, Mattias (4)
Stafström, Sven (4)
Pettersson, Robert (4)
Frisk, Erik, 1971- (3)
Krysander, Mattias, ... (3)
Frisk, Erik (2)
visa fler...
Krysander, Mattias (2)
Andersson, Mats, 196 ... (1)
Inganäs, Olle (1)
Berggren, Magnus (1)
Fink, Olga, Professo ... (1)
Kylin, Henrik (1)
PETTERSSON, R (1)
Lindh, Christian (1)
Lidén, Kerstin (1)
Storå, Jan (1)
Norinder, Ulf (1)
Zhang, Jin (1)
Norman, Patrick, Pro ... (1)
Linares, Mathieu (1)
Jakobsson, Kristina (1)
Bergman, Åke (1)
Tang, Mandy (1)
Andersson, Mattias (1)
Linderholm, Anna (1)
Cederbrant, Karin (1)
Rüegg, Joelle (1)
Holmlund, Gunilla (1)
Willerslev, Eske (1)
Lindberg, Johan (1)
Sjödin, Per (1)
Gilbert, M. Thomas P ... (1)
Knudsen, Lisbeth (1)
Cotgreave, Ian (1)
Osikowicz, Wojciech (1)
Jakobsson, Fredrik L ... (1)
Lindgren, Lars Johan ... (1)
Andersson, Patrik (1)
Bergdahl, Ingvar (1)
Forsby, Anna (1)
Jakobsson, Mattias, ... (1)
Demeneix, Barbara (1)
Skoglund, Pontus (1)
Alfaro-Moreno, Ernes ... (1)
Lupu, Diana (1)
Ghavanini, Ali Alavi ... (1)
Förare, Jonas (1)
Gustafsson, Åke (1)
Hellmond, Heike (1)
Öberg, Mattias (1)
visa färre...
Lärosäte
Stockholms universitet (1)
Chalmers tekniska högskola (1)
Språk
Engelska (16)
Forskningsämne (UKÄ/SCB)
Naturvetenskap (6)
Teknik (6)
Medicin och hälsovetenskap (1)

År

Kungliga biblioteket hanterar dina personuppgifter i enlighet med EU:s dataskyddsförordning (2018), GDPR. Läs mer om hur det funkar här.
Så här hanterar KB dina uppgifter vid användning av denna tjänst.

 
pil uppåt Stäng

Kopiera och spara länken för att återkomma till aktuell vy