| 1. |
- Kehoe, Laura, et al.
(författare)
-
Make EU trade with Brazil sustainable
- 2019
-
Ingår i: Science. - : American Association for the Advancement of Science (AAAS). - 0036-8075 .- 1095-9203. ; 364:6438, s. 341-
-
Tidskriftsartikel (övrigt vetenskapligt/konstnärligt)
|
|
| 2. |
- Connolly, David, et al.
(författare)
-
Heat Roadmap Europe 2050 : First Pre-study for the EU27
- 2012
-
Rapport (övrigt vetenskapligt/konstnärligt)abstract
- This pre-study presents the findings concerning a considerable outlined expansion of the district heating sector within the current EU27 member states until 2050. Heat deliveries are presumed to grow by a factor of 2.1 until 2030 and by a factor of 3.3 until 2050.The current energy policy context is that the latest energy communication from the European Commission (Energy Roadmap 2050) contains only a very modest growth in the future for district heating systems and additional industrial heat use from industrial CHP plants. A small increase is foreseen for industrial demands, while heat deliveries to the residential and service sectors are expected to decrease. In total, the heat delivered is expected to increase by less than one per cent per year, giving a total increase of 20% until 2030 and of 40% until 2050.In this prestudy, more ambitious growth rates are assessed for district heating in the EU27 between 2010 and 2050. The chosen methodology in this pre-study contains a combination of hour-by-hour energy modelling of the EU27 energy system and mapping of local conditions, which is essential for district heating analysis. However, the link between these two actions has not been fully utilised in this pre-study due to the limited working time available: The mapping action has only indicated the input to the energy modelling action.
|
|
| 3. |
- Ding Yuan, Chen, 1991, et al.
(författare)
-
Impact of in situ NH3 pre-treatment of LPCVD SiN passivation on GaN HEMT performance
- 2022
-
Ingår i: Semiconductor Science and Technology. - : IOP Publishing. - 1361-6641 .- 0268-1242. ; 37:3
-
Tidskriftsartikel (refereegranskat)abstract
- The impact on the performance of GaN high electron mobility transistors (HEMTs) of in situ ammonia (NH3) pre-treatment prior to the deposition of silicon nitride (SiN) passivation with low-pressure chemical vapor deposition (LPCVD ) is investigated. Three different NH3 pre-treatment durations (0, 3, and 10 min) were compared in terms of interface properties and device performance. A reduction of oxygen (O) at the interface between SiN and epi-structure is detected by scanning transmission electron microscopy (STEM )-electron energy loss spectroscopy (EELS) measurements in the sample subjected to 10 min of pre-treatment. The samples subjected to NH3 pre-treatment show a reduced surface-related current dispersion of 9% (compared to 16% for the untreated sample), which is attributed to the reduction of O at the SiN/epi interface. Furthermore, NH3 pre-treatment for 10 min significantly improves the current dispersion uniformity from 14.5% to 1.9%. The reduced trapping effects result in a high output power of 3.4 W mm(-1) at 3 GHz (compared to 2.6 W mm(-1) for the untreated sample). These results demonstrate that the in situ NH3 pre-treatment before LPCVD of SiN passivation is critical and can effectively improves the large-signal microwave performance of GaN HEMTs.
|
|
| 4. |
- Jönsson, Martin, et al.
(författare)
-
Corrosion product formation during NaCl induced atmospheric corrosion of magnesium alloy AZ91D
- 2007
-
Ingår i: Corrosion Science. - : Elsevier BV. - 0010-938X .- 1879-0496. ; 49:3, s. 1540-1558
-
Tidskriftsartikel (refereegranskat)abstract
- Magnesium alloy AZ91D was exposed in humid air at 95% relative humidity (RH) with a deposition of 70 μg/cm-2 NaCl. The corrosion products formed and the surface electrolyte were analysed after different exposure times using ex situ and in situ FTIR spectroscopy, X-ray diffraction and Ion Chromatography. The results show that magnesium carbonates are the main solid corrosion products formed under these conditions. The corrosion products identified were the magnesium carbonates hydromagnesite (Mg5 (CO3)4 (OH)24H2O) and nesquehonite (MgCO3 3H2O). The corrosion attack starts with the formation of magnesite at locations with higher NaCl contents. At 95% RH, a sequence of reactions was observed with the initial formation of magnesite, which transformed into nesquehonite after 2-3 days. Long exposures result in the formation of pits containing brucite (Mg(OH2)) covered with hydromagnesite crusts. The hydromagnesite crusts restrict the transport of CO2 and O2 to the magnesium surface and thereby favour the formation of brucite. Analysis of the surface electrolyte showed that the NaCl applied on the surface at the beginning was essentially preserved during the initial corrosion process. Since the applied salt was not bound in sparingly soluble corrosion products a layer of NaCl electrolyte was present on the surface during the whole exposure. Thus, Na+ and Cl- ions can participate in the corrosion process during the whole time and the availability of these species will not restrict the atmospheric corrosion of AZ91D under these conditions. It is suggested that the corrosion behaviour of AZ91D is rather controlled by factors related to the microstructure of the alloy and formation of solid carbonate containing corrosion products blocking active corrosion sites on the surface.
|
|
| 5. |
- Boman, Christoffer, et al.
(författare)
-
Development of innovative small(micro)-scale biomass-based CHP technologies
- 2017
-
Rapport (övrigt vetenskapligt/konstnärligt)abstract
- To enhance the overall efficiency of the use of biomass in the energy sector in Europe, the large electricity production potential from small-scale biomass heating systems should be utilised. So far, no technologically sound (in terms of efficiency and reliability) and economically affordable micro- and small-scale biomass CHP technologies are, however, available. Therefore, the present ERA-NET project (MiniBioCHP) aimed at the further development and test of new CHP technologies based on small-scale biomass combustion in the electric capacity range between some W and 100 kW. Within the project, an international consortium consisting of 12 partners from 4 countries, including university institutions, institutes and industry (both engineering and manufacturing), collaborated closely to perform high level R&D on three promising micro/small-scale biomass based CHP technologies which are covering a broad range of applications in the residential heating sector. The Austrian engineering company BIOS, coordinated the international project. The project was based on earlier basic research and development work related to these promising new technologies and aimed at the achievement of a technological level which allows a first (commercial) demonstration after the end of the project. The three CHP concepts included in the MiniBioCHP project were;1. Pellet stoves with a thermoelectric generator (TEG)2. Small-scale biomass boilers (10-30 kWth) with a micro-ORC process3. High temperature heat exchanger (HT-HE) for an externally fired gas turbine (EFGT)The Swedish part of the project was focused on the development of the concept of biomass based EFGT with dedicated R&D activities related to the development of the HT-HE system. The Swedish project consisted of the research partners Umeå University (project leader), Luleå University of Technology, Chalmers University of Technology and RISE Research Institutes of Sweden, together with the industrial partners Enertech AB/Osby Parca and Ecergy. The expertise of the Swedish partners regarding ash related problems, grate boiler combustion and modelling, deposit formation and high temperature corrosion, were combined with the know-how of a Polish partner regarding HT-HE design, construction, testing and optimisation.The HT-HE is the most crucial component in EFGT processes significantly influencing the investment costs, availabilities as well as the efficiencies that can be achieved. With a thermal capacity from several hundred kW up to 2-3 MWth) the CHP technology based on a biomass boiler and an EFGT is suitable for district heating systems, or process heat consumers. The electricity produced by the gas turbine (up to some 100 kWel) can be used to cover the own electricity consumption of a company and/or fed into the grid. Even though the concept of biomass based EFGT has been an interesting alternative for small-scale CHP production for some decades, and R&D activities have been undertaken, tackling both economic and technical aspects, only a few pilot-plants have been in operation and no initiative has so far reached the level of commercial implementation. Thus, the concept of EFGT fed with biomass is still considered to be in a rather early development stage and the main technical challenges are related to alkali deposit induced corrosion and thermal stress of the HT-HE material, turbine design/operation and system integration.Within the present project, a HT-HE prototype aimed for an EFGT system was therefore designed, constructed and successfully tested at flue gas temperatures up to 900°C. Thus, appropriate guidelines for a compact design of the HT-HE and recommendations have been worked out to minimize thermal stresses as well as ash related problems regarding ash deposit formation and high temperature corrosion in a biomass boiler system. Furthermore, different concepts for the overall biomass based EFGT system have been worked out and evaluated. The outcome of the project will hopefully be used in the further development work and form the basis for a first testing and demonstration plant within the coming years.
|
|
| 6. |
- Cheng, Hei Victor
(författare)
-
Aspects of Power Allocation in Massive MIMO
- 2016
-
Licentiatavhandling (övrigt vetenskapligt/konstnärligt)abstract
- The past decades have seen a rapid growth of mobile data trac, both in terms of connected devices and data rate. To satisfy the ever growing data trac demand in wireless communication systems, the current cellular systems have to be redesigned to increase both spectral eciency and energy eciency. Massive MIMO (Multiple-Input-Multiple-Output) is one solution that satisfy both requirements. In massive MIMO systems, hundreds of antennas are employed at the base station to provide service to many users at the same time and frequency. This enables the system to serve the users with uniformly good quality of service simultaneously, with low-cost hardware and without using extra bandwidth and energy. To achieve this, proper resource allocation is needed. Among the available resources, transmit power is one of the most important degree of freedom to control the spectral eciency and energy eciency. Due to the use of excessive number of antennas and low-end hardware at the base station, new aspects of power allocation compared to current systems arises. In the rst part of the thesis, a new uplink power allocation schemes that based on long term channel statistics is proposed. Since quality of the channel estimates is crucial in massive MIMO, in addition to data power allocation, joint power allocation that includes the pilot power as additional variable should be considered. Therefore a new framework for power allocation that matches practical systems is developed, as the methods developed in the literature cannot be applied directly to massive MIMO systems. Simulation results conrm the advantages brought by the the proposed new framework. In the second part of the thesis, we investigate the eects of using low-end ampliers at the base stations. The non-linear behavior of power consumption in these ampliers changes the power consumption model at the base station, thereby changes the power allocation. Two dierent scenarios are investigated and both results show that a certain number of antennas can be turned o in low load scenarios.
|
|
| 7. |
- Cheng, Hei Victor, et al.
(författare)
-
Massive MIMO at Night : On the Operation of Massive MIMO in Low Traffic Scenarios
- 2015
-
Ingår i: 2015 IEEE INTERNATIONAL CONFERENCE ON COMMUNICATIONS (ICC). - : IEEE. - 9781467364324 - 9781467364317 - 9781467364300 ; , s. 1697-1702
-
Konferensbidrag (refereegranskat)abstract
- For both maximum ratio transmission (MRT) and zero forcing (ZF) precoding schemes and given any specific rate requirement the optimal transmit power, number of antennas to be used, number of users to be served and number of pilots spent on channel training are found with the objective to minimize the total consumed power at the base station. The optimization problem is solved by finding closed form expressions of the optimal transmit power and then search over the remaining discrete variables. The analysis consists of two parts, the first part investigates the situation when only power consumed in the RF amplifiers is considered. The second part includes both the power consumed in the RF amplifiers and in other transceiver circuits. In the former case having all antennas active while reducing the transmit power is optimal. Adaptive scheme to switch off some of the antennas at the base stations is found to be optimal in the latter case.
|
|
| 8. |
- Wilson, Stephen A., et al.
(författare)
-
New materials for micro-scale sensors and actuators An engineering review
- 2007
-
Ingår i: Materials science & engineering. R, Reports. - : Elsevier BV. - 0927-796X .- 1879-212X. ; 56:06-jan, s. 1-129
-
Forskningsöversikt (refereegranskat)abstract
- This paper provides a detailed overview of developments in transducer materials technology relating to their current and future applications in micro-scale devices. Recent advances in piezoelectric, magnetostrictive and shape-memory alloy systems are discussed and emerging transducer materials such as magnetic nanoparticles, expandable micro-spheres and conductive polymers are introduced. Materials properties, transducer mechanisms and end applications are described and the potential for integration of the materials with ancillary systems components is viewed as an essential consideration. The review concludes with a short discussion of structural polymers that are extending the range of micro-fabrication techniques available to designers and production engineers beyond the limitations of silicon fabrication technology.
|
|
| 9. |
- Niklasson, Fredrik, et al.
(författare)
-
Branschgemensam forskning för småskaliga biobränslepannor inför ekodesign
- 2018
-
Rapport (övrigt vetenskapligt/konstnärligt)abstract
- Nytillverkade småskaliga biobränslepannor måste uppfylla ekodesignkraven senast år 2020. I en marknadsundersökning från 2014 klarade ingen av 11 testade pelletspannor alla ställda krav, vilket tydligt visar på ett utvecklingsbehov. Föreliggande projekt har haft som syfte att panntillverkare och forskningsinstitut branschgemensamt ska bemöta de förbränningstekniska utmaningar som tillverkarna står inför.För pelletspannor är den största utmaningen med ekodesigndirektivet att prestanda till största delen beräknas från drift vid partiell last (låg last). Tidigare har prestanda bara fastställts vid nominell last och designen optimerats därefter. I detta projekt har tester körts med två moderna pelletspannor som har olika typer av pelletsbrännare: en med horisontellt brännarrör och en med undermatad brännarkopp. Resultaten visar att tillräckligt god förbränning kunde upprätthållas vid partiell last med båda brännartyperna. Dock uppvisade rörbrännaren betydligt lägre emissioner vid partiell last, troligtvis beroende på att förbränningszonen i denna brännare är skyddad från värmestrålningsutbyte med kylande pannväggar. Ett ganska omfattande arbete lades ned på att förse koppbrännaren med en skyddande krage som skulle skydda förbränningszonen. Det resulterade dock inte in någon betydande förbättring, antagligen beroende på att tillförseln av sekundärluft inte blev optimal. Ett mer omfattande arbete krävs för att utveckla en optimal brännardesign av denna typ.För vedpannor är det en utmaning att klara ekodesigndirektivets NOx-krav på 200 mg/Nm³. En mängd temperaturmätningar i en vedpanna för villabruk resulterade i att termisk NOx-bildning kunde uteslutas. Pannan förseddes med ett system för rökgasåterföring, men det minskade inte NOx-emissionen. Därefter provades olika vedsorter. NOx-emissionen kunde minskas till att klara gränsvärdet med avbarkad björkved. Kemiska analyser visade att björkbarken innehöll 0,49% kväve jämfört med 0,09% i stamveden. Även granved gav låga NOx-emissioner, men det bränslet medförde ökade emissioner av CO och OGC. För att vedpannor ska klara kraven på CO, OGC och stoft krävs optimering med avseende på vedens slutförbränningsfas. I det skedet är emissionerna som högst, vilket beror på att värmeeffekten avtar och luftflödet tenderar att kyla ned rökgasen innan de brännbara gaserna brunnit ut. Den optiska partikelmätningen visade tydlig korrelation mellan stoft och CO i rökgasen. Om pannan uppfyller gränsvärdet för CO så finns goda chanser att även kravet på partiklar uppfylls.Verkningsgraden som anges i ekodesigndirektivet beräknas utgående från bränslets övre värmevärde. Dessutom subtraheras vissa förlustfaktorer. Detta innebär att pannan inte får ha några onödigt stora värmeförluster eller omotiverat hög elförbrukning för att klara satta krav. Mätningar visade att den största förlusten sker via värmen i rökgasen. Den näst största förlustposten är värmetransport från pannkroppen. För verkningsgraden ökar betydelsen av en välisolerad pannkropp vid partiell last. De två pelletspannor som användes inom projektet låg väl till för att kunna uppfylla ekodesigndirektivets krav på verkningsgrad.
|
|
| 10. |
- Abay, Simon, 1980, et al.
(författare)
-
Quantized Conductance and Its Correlation to the Supercurrent in a Nanowire Connected to Superconductors
- 2013
-
Ingår i: Nano Letters. - : American Chemical Society (ACS). - 1530-6992 .- 1530-6984. ; 13:8, s. 3614-3617
-
Tidskriftsartikel (refereegranskat)abstract
- We report conductance and supercurrent of InAs nano wires coupled to Al-superconducting electrodes with short channel lengths and good Ohmic contacts. The nanowires are suspended 15 nm above a local gate electrode. The charge density in the nanowires can be controlled by a small change in the gate voltage. For large negative gate voltages, the number of conducting channels is reduced gradually, and we observe a stepwise decrease of both conductance and critical current before the conductance vanishes completely.
|
|
