| 1. |
- Berndt, Sonja I., et al.
(författare)
-
Genome-wide meta-analysis identifies 11 new loci for anthropometric traits and provides insights into genetic architecture
- 2013
-
Ingår i: Nature Genetics. - : Springer Science and Business Media LLC. - 1061-4036 .- 1546-1718. ; 45:5, s. 501-U69
-
Tidskriftsartikel (refereegranskat)abstract
- Approaches exploiting trait distribution extremes may be used to identify loci associated with common traits, but it is unknown whether these loci are generalizable to the broader population. In a genome-wide search for loci associated with the upper versus the lower 5th percentiles of body mass index, height and waist-to-hip ratio, as well as clinical classes of obesity, including up to 263,407 individuals of European ancestry, we identified 4 new loci (IGFBP4, H6PD, RSRC1 and PPP2R2A) influencing height detected in the distribution tails and 7 new loci (HNF4G, RPTOR, GNAT2, MRPS33P4, ADCY9, HS6ST3 and ZZZ3) for clinical classes of obesity. Further, we find a large overlap in genetic structure and the distribution of variants between traits based on extremes and the general population and little etiological heterogeneity between obesity subgroups.
|
|
| 2. |
- Attallah, Moataz M., et al.
(författare)
-
Microstructural and Residual Stress Development due to Inertia Friction Welding in Ti-6246
- 2012
-
Ingår i: Metallurgical and Materials Transactions A - Physical Metallurgy and Materials Science. - : Springer Science and Business Media LLC. - 1073-5623. ; 43A:9, s. 3149-3161
-
Tidskriftsartikel (refereegranskat)abstract
- A thorough investigation has been performed to assess the microstructural properties, mechanical properties (hardness and elastic modulus), and residual stress development in Ti-6Al-2Sn-4Zr-6Mo (Ti-6246) inertia friction welds in the as-welded and postweld heat-treated conditions. It was evident that the thermomechanical deformation in the weld region occurred above the beta transus, forming dynamically recrystallized beta grains and precipitating acicular alpha within the beta grains, which resulted in a localized hardness increase. In the heat-affected zone, a ghost microstructure of the base metal formed because of the absence of sufficient time for diffusion, resulting in Mo segregation in the prior primary alpha plates. Energy-dispersive synchrotron X-ray diffraction and neutron diffraction were used to assess the residual stress development in the three principal directions. The variation in the unstrained lattice parameters across the weld regions was established by imposing a stress balance on the axial stress component in the radial direction. It was found that the maximum stresses occurred in the hoop direction, with significantly lower stresses present in the radial and axial directions. The maximum tensile hoop stresses were located at similar to 4 mm from the weld centerline and not at the dynamically recrystallized beta-rich weld zone. This was associated with the alpha -> beta phase transformation and the subsequent acicular alpha precipitation within the region surrounding the weld centerline.
|
|
| 3. |
- Topping, Matthew, et al.
(författare)
-
The effect of iron on dislocation evolution in model and commercial zirconium alloys
- 2018
-
Ingår i: ASTM Special Technical Publication. - 0066-0558. ; STP 1597, s. 796-822
-
Konferensbidrag (refereegranskat)abstract
- Although the evolution of irradiation-induced dislocation loops has been well correlated with irradiation-induced growth phenomena, the effect of alloying elements on this evolution remains elusive, especially at low fluences. To develop a more mechanistic understanding of the role iron has on loop formation, we used state-of-the-art techniques to study a proton-irradiated Zr-0.1Fe alloy and proton- and neutron-irradiated Zircaloy-2. The two alloys were irradiated with 2-MeV protons up to 7 dpa at 350°C and Zircaloy-2 up to 14.7 × 1025n • m-2, approximately 24 dpa, in a boiling water reactor at approximately 300°C. Baseline transmission electron microscopy showed that the Zr3Fe secondary-phase particles in the binary system were larger and fewer in number than the Zr (Fe, Cr)2and Zr2(Fe, Ni) particles in Zircaloy-2. An analysis of the irradiated binary alloy revealed only limited dissolution of Ze3Fe, suggesting little dispersion of iron into the matrix, while at the same time a higher 〈a〉-loop density was observed compared with Zircaloy-2 at equivalent proton dose levels. We also found that the redistribution of iron during irradiation led to the formation of iron nanoclusters. A delay in the onset of 〈c〉-loop nucleation in proton-irradiated Zircaloy-2 compared with the binary alloy was observed. The effect of iron redistributed from secondary-phase particles because of dissolution on the density and morphology of 〈a〉 and 〈c〉 loops is described. The implication this may have on irradiation-induced growth of zirconium fuel cladding is also discussed.
|
|
