| 1. |
- Fomalont, E. B., et al.
(författare)
-
THE 2014 ALMA LONG BASELINE CAMPAIGN: AN OVERVIEW
- 2015
-
Ingår i: Astrophysical Journal Letters. - : American Astronomical Society. - 2041-8213 .- 2041-8205. ; 808:1
-
Tidskriftsartikel (refereegranskat)abstract
- A major goal of the Atacama Large Millimeter/submillimeter Array (ALMA) is to make accurate images with resolutions of tens of milliarcseconds, which at submillimeter (submm) wavelengths requires baselines up to similar to 15 km. To develop and test this capability, a Long Baseline Campaign (LBC) was carried out from 2014 September to late November, culminating in end-to-end observations, calibrations, and imaging of selected Science Verification (SV) targets. This paper presents an overview of the campaign and its main results, including an investigation of the short-term coherence properties and systematic phase errors over the long baselines at the ALMA site, a summary of the SV targets and observations, and recommendations for science observing strategies at long baselines. Deep ALMA images of the quasar 3C 138 at 97 and 241 GHz are also compared to VLA 43 GHz results, demonstrating an agreement at a level of a few percent. As a result of the extensive program of LBC testing, the highly successful SV imaging at long baselines achieved angular resolutions as fine as 19 mas at similar to 350 GHz. Observing with ALMA on baselines of up to 15 km is now possible, and opens up new parameter space for submm astronomy.
|
|
| 2. |
- Koundouri, P., et al.
(författare)
-
Methodology for Integrated Socio-economic Assessment of Multi-use Offshore Platforms.
- 2017
-
Ingår i: In: Koundouri P. (eds) The Ocean of Tomorrow. Environment & Policy, vol 56. Springer, Cham. - 9783319557700 ; , s. 11-26
-
Bokkapitel (övrigt vetenskapligt/konstnärligt)abstract
- This chapter presents the methodology employed for the Integrated Socio-Economic Assessment (MISEA) of different designs of Multi-Use Offshore Platforms (MUOPs). The methodology allows for the identification, the valuationand the assessment of the potential impacts and their magnitude. The analysis considers a number of feasible designs of MUOP investments, and the likely responsesof those impacted by the investment project. The approach provides decision-makers with a valuable tool to assess whether a MUOP project increases the overall social welfare and hence should be undertaken. This is performed under alternative specifications regarding platform design, the discount rate and the stream of net benefits, if a Cost-Benefit Analysis (CBA) is to be followed or a sensitivity analysis of selected criteria in a Multi-Criteria Decision Analysis (MCDA) framework. Themethodology can support the implementation of policies aiming at achieving a goodenvironmental status of the EU’s marine waters and the protection of the resource base upon which marine-related economic and social activities depend.
|
|
| 3. |
- Öjekull, Jenny, 1973, et al.
(författare)
-
Dissociative recombination of H+(H2O)3 and D+(D2O)3 water cluster ions with electrons: Cross sections and branching ratios
- 2007
-
Ingår i: The Journal of chemical physics. - : AIP Publishing. - 0021-9606 .- 1089-7690. ; 127, s. 194301-194309
-
Tidskriftsartikel (refereegranskat)abstract
- Dissociative recombination (DR) of the water cluster ions H+(H2O)3 and D+(D2O)3 with electrons has been studied at the heavy-ion storage ring CRYRING (Manne Siegbahn Laboratory, Stockholm University). For the first time, absolute DR cross sections have been measured for H+(H2O)3 in the energy range of 0.001–0.8 eV, and relative cross sections have been measured for D+(D2O)3 in the energy range of 0.001–1.0 eV. The DR cross sections for H+(H2O)3 are larger than previously observed for H+(H2O)n (n=1,2), which is in agreement with the previously observed trend indicating that the DR rate coefficient increases with size of the water cluster ion. Branching ratios have been determined for the dominating product channels. Dissociative recombination of H+(H2O)3 mainly results in the formation of 3H2O+H (probability of 0.95±0.05) and with a possible minor channel resulting in 2H2O+OH+H2 (0.05±0.05). The dominating channels for DR of D+(D2O)3 are 3D2O+D (0.88±0.03) and 2D2O+OD+D2 (0.09±0.02). The branching ratios are comparable to earlier DR results for H+(H2O)2 and D+(D2O)2, which gave 2X2O+X (X=H,D) with a probability of over 0.9.
|
|
| 4. |
- Öjekull, Jenny, 1973, et al.
(författare)
-
Dissociative recombination of NH4+ and ND4+ ions : Storage ring experiments and ab initio molecular dynamics
- 2004
-
Ingår i: Journal of Chemical Physics. - : AIP Publishing. - 0021-9606 .- 1089-7690. ; 120:16, s. 7391-7399
-
Tidskriftsartikel (refereegranskat)abstract
- The dissociative recombination (DR) process of NH4+ and ND4+ molecular ions with free electrons has been studied at the heavy-ion storage ring CRYRING (Manne Siegbahn Laboratory, Stockholm University). The absolute cross sections for DR of NH4+ and ND4+ in the collision energy range 0.001-1 eV are reported, and thermal rate coefficients for the temperature interval from 10 to 2000 K are calculated from the experimental data. The absolute cross section for NH4+ agrees well with earlier work and is about a factor of 2 larger than the cross section for ND4+. The dissociative recombination of NH4+ is dominated by the product channels NH3+H (0.85+/-0.04) and NH2+2H (0.13+/-0.01), while the DR of ND4+ mainly results in ND3+D (0.94+/-0.03). Ab initio direct dynamics simulations, based on the assumption that the dissociation dynamics is governed by the neutral ground-state potential energy surface, suggest that the primary product formed in the DR process is NH3+H. The ejection of the H atom is direct and leaves the NH3 molecule highly vibrationally excited. A fraction of the excited ammonia molecules may subsequently undergo secondary fragmentation forming NH2+H. It is concluded that the model results are consistent with gross features of the experimental results, including the sensitivity of the branching ratio for the three-body channel NH2+2H to isotopic exchange.
|
|
| 5. |
- Bender, Johanna, 1975, et al.
(författare)
-
Lipid cubic phases for improved topical drug delivery in photodynamic therapy.
- 2005
-
Ingår i: Journal of Controlled Release. - : Elsevier BV. - 0168-3659 .- 1873-4995. ; 106:3, s. 350-360
-
Tidskriftsartikel (refereegranskat)abstract
- We have evaluated the efficacy of lipid cubic phases, highly ordered self-assembly systems on the nanometer level, as drug delivery vehicles for in vivo topical administration of delta-aminolevulinic acid (ALA) and its methyl ester (m-ALA) on nude mice skin. ALA, a precursor of heme, induces the production of the photosensitizer protoporphyrin IX (PpIX) in living tissue. Measuring the PpIX fluorescence at the skin surface, after topical administration, makes indirect quantification of the penetration of ALA into the tissue possible. Cubic phases were formed of lipid (monoolein or phytantriol), water and drug. In some cases, propylene glycol was included in the cubic phase as well. The drug concentration was 3% (w/w, based on the total sample weight) in all investigated vehicles. When the formulations were applied for 1 h, the monoolein cubic systems and the three-component phytantriol sample showed higher fluorescence compared to the standard ointment during the 10 h of measurement. Both ALA and m-ALA yielded similar results, although the differences between the investigated vehicles were more pronounced when using m-ALA. For the 24-h applications, the monoolein cubic systems with m-ALA showed faster PpIX formation than the standard ointment, implying higher PpIX levels at short application times (less than 4 h). The systemic PpIX fluorescence of ALA was elevated by using the lipid cubic formulations. Notably, a small systemic effect was also observed for the monoolein cubic sample with m-ALA. These results imply improved PpIX formation when using the lipid cubic systems, most probably due to enhanced drug penetration.
|
|
| 6. |
- Berglund, Johan C, 1978, et al.
(författare)
-
On discovering relevant scales in surface roughness measurement : an evaluation of a band-pass method
- 2010
-
Ingår i: Scanning. - London : John Wiley & Sons. - 0161-0457 .- 1932-8745. ; 32:4, s. 244-249
-
Tidskriftsartikel (refereegranskat)abstract
- When characterizing surfaces and searching for correlations to functional properties, such as friction, finding the right scale of roughness for evaluation can improve correlations. However, in traditional roughness parameter analysis, a wide range of scales, or all scales of topography in the surface roughness measurements are evaluated together. In this study a multi-scale method using a series of band-pass filters is employed for finding scales of topography with strong correlations to friction.
|
|
| 7. |
- Dimkovski, Zlate
(författare)
-
Surfaces of Honed Cylinder Liners
- 2011
-
Doktorsavhandling (övrigt vetenskapligt/konstnärligt)abstract
- Cylinder liner surfaces are often on the agenda of engine developers because of their large influence on the frictional losses, oil consumption and emissions of internal combustion engines. Improving the liner function involves not only manufacturing new surfaces and checking their function but also characterising them as a necessary intermediate step for better understanding of the changes made. In the manufacturing of the liners, honing is a well adapted and widely used finishing process and along with the characterisation and function has been the subject of studies in this thesis. Regarding the liner’s function, three phenomena were monitored: wear, friction and oil passage rate (correlated with engine’s oil consumption). The first one was studied experimentally while the other two were simulated. Only the interactions with the twin land oil control ring were simulated as it has the greatest influence on the control of friction and oil consumption of all other rings. In the mid-stroke region of truck engine liners, the presence of axial wear scratches was observed and their relation with the removal of the cold worked material (“Blechmantel”) folded inside the deep honing grooves was investigated. Algorithms were developed for estimating the extent of Blechmantel, revealing that most of it remained on the surface whereas the engines still performed well. Other algorithms for characterising honing angle, balance of honing texture, width, height, distance between honing grooves/axial wear scratches, etc were developed for quicker and more objective inspection of unworn and worn surfaces from 3D interference measurements. Based on such 3D measurements, the algorithms were incorporated in a characterisation tool enabling rating of the surfaces and determining the number of measurements necessary to achieve stable roughness parameter values. In addition, it was found that interference measurements are more suitable for quantification of the deposits on the worn truck liner surfaces compared with scanning electron microscope measurements. The lubrication and friction of flat oil control ring lands and differently slide honed surfaces of truck liners were simulated. Friction mean effective pressure and oil passage rate were calculated for each surface showing in each case a reduction for the surfaces with smoother plateaus and smaller valleys. Such a liner surface was finished by using a low base honing pressure and a longer plateau honing time. In a car engine, the influence of different liner surfaces, ring land widths and tensions was examined by running simulations. The results suggest that a considerably improved function can be achieved if the ring land width and tension are reduced whereby the differences between the liner surfaces would reduce.
|
|
| 8. |
- Ding, Feng, 1970, et al.
(författare)
-
Graphitic encapsulation of catalyst particles in carbon nanotube production
- 2006
-
Ingår i: Journal of Physical Chemistry B. - : American Chemical Society (ACS). - 1520-5207 .- 1520-6106. ; 110:15, s. 7666-7670
-
Tidskriftsartikel (refereegranskat)abstract
- A new model is proposed for the encapsulation of catalyst metal particles by graphite layers that are obtained, for example, in low-temperature chemical vapor deposition production of carbon nanotubes (CNTs). In this model graphite layers are primarily formed from the dissolved carbon atoms in the metal-carbide particle when the particle cools. This mechanism is in good agreement with molecular dynamics simulations (which show that precipitated carbon atoms preferentially form graphite sheets instead of CNTs at low temperatures) and experimental results (e.g., encapsulated metal particles are found in low-temperature zones and CNTs in high-temperature regions of production apparatus, very small catalyst particles are generally not encapsulated, and the ratio of the number of graphitic layers to the diameter of the catalyst particle is typically 0.25 nm(-1)).
|
|
| 9. |
- Ericson, Marica B, 1974, et al.
(författare)
-
Bispectral fluorescence imaging combined with texture analysis and linear discrimination for correlation with histopathologic extent of basal cell carcinoma
- 2005
-
Ingår i: Journal of Biomedical Optics. - : SPIE-Intl Soc Optical Eng. - 1083-3668 .- 1560-2281. ; 10:3
-
Tidskriftsartikel (refereegranskat)abstract
- Fluorescence imaging has been shown to be a potential complement to visual inspection for demarcation of basal cell carcinoma (BCC), which is the most common type of skin cancer. Earlier studies have shown promising results when combining autofluorescence with protoporphyrin IX (Pp IX) fluorescence, induced by application of delta-5-aminolaevulinic acid (ALA). In this work, we have tried to further improve the ability of this technique to discriminate between areas of tumor and normal skin by implementing texture analysis and Fisher linear discrimination (FLD) on bispectral fluorescence data of BCCs located on the face. Classification maps of the lesions have been obtained from histopathologic mapping of the excised tumors. The contrast feature obtained from co-occurrence matrices was found to provide useful information, particularly for the ALA-induced Pp IX fluorescence data. Moreover, the neighborhood average features of both autofluorescence and Pp IX fluorescence were preferentially included in the analysis. The algorithm was trained by using a training set of images with good agreement with histopathology, which improved the discriminability of the validation set. In addition, cross validation of the training set showed good discriminability. Our results imply that FLD and texture analysis are preferential for correlation between bispectral fluorescence images and the histopathologic extension of the tumors.
|
|
| 10. |
- Ericson, Marica, 1974, et al.
(författare)
-
Photodynamic therapy of actinic keratosis at varying fluence rates : Assessment of photobleaching, pain and primary clinical outcome
- 2004
-
Ingår i: British Journal of Dermatology. - : Oxford University Press (OUP). - 0007-0963 .- 1365-2133. ; 151, s. 1204-1212
-
Tidskriftsartikel (refereegranskat)abstract
- Background: Although photodynamic therapy (PDT) is becoming an important treatment method for skin lesions such as actinic keratosis (AK) and superficial basal cell carcinoma, there are still discussions about which fluence rate and light dose are preferable. Recent studies in rodents have shown that a low fluence rate is preferable due to depletion of oxygen at high fluence rates. However, these results have not yet been verified in humans. Objectives: The objective was to investigate the impact of fluence rate and spectral range on primary treatment outcome and bleaching rate in AK using aminolaevulinic acid PDT. In addition, the pain experienced by the patients has been monitored during treatment. Patients/methods Thirty-seven patients (mean age 71 years) with AK located on the head, neck and upper chest were treated with PDT, randomly allocated to four groups: two groups with narrow filter (580-650 nm) and fluence rates of 30 or 45 mW cm-2, and two groups with broad filter (580-690 nm) and fluence rates of 50 or 75 mW cm-2. The total cumulative light dose was 100 J cm-2 in all treatments. Photobleaching was monitored by fluorescence imaging, and pain experienced by the patients was registered by using a visual analogue scale graded from 0 (no pain) to 10 (unbearable pain). The primary treatment outcome was evaluated at a follow-up visit after 7 weeks. Results: Our data showed a significant correlation between fluence rate and initial treatment outcome, where lower fluence rate resulted in favourable treatment response. Moreover, the photo-bleaching dose (1/e) was found to be related to fluence rate, ranging from 4.5 ± 1.0 J cm -2 at 30 mW cm-2, to 7.3 ± 0.7 J cm-2 at 75 mW cm-2, indicating higher oxygen levels in tissue at lower fluence rates. After a cumulative light dose of 40 J cm-2 no further photobleaching took place, implying that higher doses are excessive. No significant difference in pain experienced by the patients during PDT was observed in varying the fluence rate from 30 to 75 mW cm-2. However, the pain was found to be most intense up to a cumulative light dose of 20 J cm-2. Conclusions: Our results imply that the photobleaching rate and primary treatment outcome are dependent on fluence rate, and that a low fluence rate (30 mW cm-2) seems preferable when performing PDT of AK using noncoherent light sources.
|
|
